dallmeier VSC-1 Operating and maintenance instructions

English
Rev. 4.0.0 / 091223
Installation and Configuration
Video System Controller
VSC-1

VSC-1
www.dallmeier.com 2
Information about copyright, trademarks, design patents
© 2009 Dallmeier electronic
All rights reserved. This document may not be copied, photocopied, reproduced, translated,
transferred to an electronic medium or converted to a machine-readable form either whole or in
part without rst receiving written permission from Dallmeier electronic GmbH & Co.KG.
We reserve the right to make technical modications.
The manufacturer accepts no liability for damage to property or pecuniary damages arising due
to minor defects of the product or documentation, e.g. print or spelling errors, and for those not
caused by intention or gross negligence of the manufacturer.
Dallmeier electronic GmbH & Co.KG
Cranachweg 1
93051 Regensburg
Germany
www.dallmeier.com
[e-mail]

VSC-1
www.dallmeier.com 3
Table of Contents
1 Introduction ...................................................................................................5
1.1 Validity .............................................................................................................5
1.2 Documents ......................................................................................................5
1.3 Conventions ....................................................................................................5
2 Safety Instructions........................................................................................7
3 General Notes................................................................................................9
3.1 Scope of Delivery ............................................................................................9
3.2 Transportation and Packaging ........................................................................9
3.3 Appropriate Use ..............................................................................................9
3.4 Performance Features ....................................................................................9
3.5 Warranty .......................................................................................................10
3.6 Approvals/Certications ................................................................................10
4 Key Assignment and Connections ............................................................11
4.1 Key Assignment ............................................................................................11
4.1.1 PTZ Control...................................................................................................12
4.1.2 Play Control ..................................................................................................13
4.2 Connections ..................................................................................................14
5 Connection and Commissioning ...............................................................15
5.1 Connection ....................................................................................................17
5.1.1 VSC-1 and Recorder via USB.......................................................................17
5.1.2 VSC-1 and Recorder via DNI ........................................................................17
5.1.3 DNI and Dome Camera ................................................................................18
5.1.4 Connection DNI and Recorder ......................................................................18
5.1.5 Connection DNI network ...............................................................................19
5.2 Commissioning .............................................................................................19
6 Conguration ..............................................................................................20
6.1 Permissions on the Recorder........................................................................20
6.2 Connection DNI.............................................................................................21
6.2.1 Serial Interface ..............................................................................................21
6.2.2 Protocol DNI..................................................................................................21
6.3 Control Protocol VSC ....................................................................................23
6.4 Keyboard Functions ......................................................................................23
7 Operation .....................................................................................................25
7.1 PTZ Control...................................................................................................25
7.1.1 Selecting Cameras........................................................................................25
7.1.2 Camera Control.............................................................................................25
7.1.3 Functions ......................................................................................................26
7.1.3.1 Preset............................................................................................................26
7.1.3.2 Tour ...............................................................................................................26
7.1.3.3 Pattern ..........................................................................................................26
7.1.3.4 Scan ..............................................................................................................27

VSC-1
www.dallmeier.com 4
7.2 Replay Control ..............................................................................................27
7.2.1 Selecting a Track ..........................................................................................27
7.2.2 Control of Replay ..........................................................................................27
7.2.3 Search...........................................................................................................28
8 Maintenance ................................................................................................29
9 Technical Data .............................................................................................30

VSC-1
www.dallmeier.com 5
1 Introduction
1.1 Validity
This document applies to the Video System Controller VSC-1. It has been produced on the
basis of version D1.7 (software).
Pictures in this document may differ from the actual product.
1.2 Documents
Commissioning
The document entitled “Commissioning” contains the most important steps for the connec-
tion and commissioning of the device.
Installation and Conguration (this document)
The document entitled “Installation and Conguration” contains detailed descriptions of
the installation, connection, commissioning and conguration of the device. Safety instruc-
tions, general notes and technical data are additionally provided.
The target audience is exclusively specially trained and authorized professionals (install-
ers).
1.3 Conventions
This document contains various warning words and symbols that indicate potential sources
of danger.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
NOTICE
NOTICE indicates practices for preventing property damage, incorrect
congurations or faulty operations.
Instructions are indicated by arrows ().

VSC-1
www.dallmeier.com 6
Expressions in bold/italics generally indicate a control element on the device (switches or
labels) or on its user interface (buttons, menu entries).
Paragraphs in italics provide information on basic principles, special features and efcient
procedure as well as general recommendations.

VSC-1
www.dallmeier.com 7
2 Safety Instructions
Only use this unit if it is technically in proper working order, to the intended purpose and
while keeping safety and potential dangers in mind.
Qualied personnel
Installation, mounting, connection, commissioning and conguration of the unit may only
be carried out by qualied personnel. This also applies to the maintenance, testing and re-
pair, whereat the regulations of the DIN VDE 0701 series of standards (repair, modication
and inspection of electrical appliances) must be followed.
Regulations
The use of video and audio surveillance systems in general is strictly regulated. Inform
yourself about the applicable laws and regulations regarding data, working and environ-
mental protection before using the unit and ensure compliance with them.
System components
Only use internal components that have been tested and approved by Dallmeier. Inappro-
priate internal components can cause malfunctions, damages and data loss and can result
in loss of warranty.
Modications
Do not make any modications to the hardware or software that has not been tested and
approved by Dallmeier. Inappropriate modications can cause malfunctions, damages and
data loss and can result in loss of warranty.
Documentation
Carefully and completely read the documents included in delivery. Always observe the
contained instructions, notes and warnings.
Condensation water
If the unit is brought from a cold to a warm environment, resulting condensation water
can cause malfunctions and damages. In this case wait (up to 8 hours) until the unit has
reached room temperature before commissioning.
Operating conditions
Unfavourable operating conditions can shorten the life of the unit and can cause malfunc-
tions, damages and data loss and can result in loss of warranty. Observe the specications
given in the technical data, the operating condition requirements and the maintenance
instructions.
Shocks
Shocks can cause malfunctions and damages. The unit may not be moved while in opera-
tion.
Foreign bodies
If objects or liquids get into the unit, immediately disconnect it from the power supply (pull
out the power plug). Contact the sales partner responsible for your area.

VSC-1
www.dallmeier.com 8
Burnt smell
If you notice burnt smell or formation of smoke from the unit, immediately disconnect it from
the power supply (pull out the power plug). Contact the sales partner responsible for your
area.
Opening
The housing of the unit may only be opened by qualied personnel for commissioning,
inspection, maintenance and repair.
Disposal
Disconnect the unit from the power supply. Remove all connected devices. Return the unit
to your respective sales partner.

VSC-1
www.dallmeier.com 9
3 General Notes
3.1 Scope of Delivery
Included in the standard scope of delivery is:
1× Keyboard VSC-1
1× Power supply unit (12 V DC)
1× Weidmüller plug connector 8-pin
1× USB cable
1× Documentation “Installation and Conguration” (CD)
1× Documentation “Commissioning” (in print)
The scope of delivery may differ depending on the ordered equipment, the device variant
or the country of destination.
The functional range of the device depends on the ordered equipment or device variant
and may differ from this document’s content. Certain functions and features may require an
activation that is subject to costs.
3.2 Transportation and Packaging
Store the original packaging for transportation at a later date. Dallmeier electronic is not
responsible for damage resulting from unprofessional/improper transportation. The goods
should only be shipped in their original packaging.
If the original packaging is no longer available, ensure that the packaging used sufciently
protects the unit against damage, moisture, heat and cold.
3.3 Appropriate Use
The Dallmeier VSC-1 (Video System Controller) is a keyboard for the remote control and
display of up to 24 cameras. Its ergonomic design and compact conguration allow a user
friendly and efcient operation even when little room is available.
3.4 Performance Features
• Remote control of speed, pan/tilt, focus, zoom and iris functions of the PTZ dome cam-
eras
• Interface controller: RS422, RS485 and USB
• Control via recorder (at USB) up recorder version V6.3.0
• Baud rate 2.4 up to 57.6 kbps
• Supported protocols: Pelco D, Pelco P
• Control up to 24 PTZ dome cameras
• User friendly tri-axial joystick
• Integrated LCD display
• Marked function buttons
• Low-maintenance rubber keyboard
For detailed information see chapter “Technical Data” on page 30.

VSC-1
www.dallmeier.com 10
3.5 Warranty
The terms and conditions valid at the signing of the contract shall apply.
3.6 Approvals/Certications
Following approvals/certications were valid at the time of document compilation.
Refer to www.dallmeier.com for possible updates.
• CE
• FCC
• RoHs

VSC-1
www.dallmeier.com 11
4 Key Assignment and Connections
4.1 Key Assignment
Fig. 4-1
Fig. 4-2
ESC/PWR On / Off (push for more than 2 seconds), exit dialogue
Maustaste Switching DNI / USB function
Fig. 4-3
Number pad PTZ control: Selection – Camera, Preset, Scan, Pattern
Play control: Camera selection, Step size for search
CLR Correction button
ENT Enter button

VSC-1
www.dallmeier.com 12
4.1.1 PTZ Control
Function Buttons
Fig. 4-4
PSET/F1 Save and run presets (camera positions)
TOUR/F2 Run a saved tour
PATT/F3 Run a saved pattern (detailed tour)
SCAN/F4 Run a saved pan range
MENU/AUTO Dome camera conguration dialogue
Keyboard function buttons
Fig. 4-5
HOLD Lock keyboard. A password has to be entered for reactivation (default
password: 0000)
AUX Switching to live mode
OPEN SHIFT + button: open aperture;
Switching to play mode
CLOSE SHIFT + button: close aperture
SET Conguration dialogues
SHIFT/TURBO Accelerate camera movement (inactive)
Fig. 4-6
NEAR – FAR Focus in / out (focal length)

VSC-1
www.dallmeier.com 13
Fig. 4-7
TELE/L – WIDE/R Zoom in / out
4.1.2 Play Control
Function Buttons
Fig. 4-8
PSET/F1 Day
TOUR/F2 Hour
PATT/F3 Minute
SCAN/F4 Second
Keyboard Function Buttons
Fig. 4-9
AUX Switching to live mode
OPEN Switching to play mode
Fig. 4-10
FAR One image forward
NEAR One image reverse

VSC-1
www.dallmeier.com 14
Fig. 4-11
WIDE/R Play forward
TELE/L Play reverse
4.2 Connections
Joystick
Power USB interface Serial interface Data interface (inactive)
Fig. 4-12

VSC-1
www.dallmeier.com 15
5 Connection and Commissioning
The VSC-1 can be connected directly via a USB port or via a DNI (Dallmeier Network Inter-
face) to the recorder and to the dome cameras.
Dome cameras normally will be connected via a DNI to the recorder. A connection via the
serial interface is available for special Dallmeier dome cameras.
DNI Connections only (PTZ Control only)
Recorder
Keyboard
DNI slave
DNI slave
DNI master
Dome cameras
Fig. 5-1
VSC-1 and Dome are connected via a DNI. In this case searing is possible even if the re-
corder is switched off.

VSC-1
www.dallmeier.com 16
DNI and USB Connection (PTZ and Play Control)
DNI slave
DNI master
Recorder
Keyboard
Dome cameras
Fig. 5-2
The domes are connected via a DNI, the VSC-1 via the USB interface. The conguration of
the DNI for the VSC-1 is not required.
For further conguration examples refer to the DNI-1 documentation “Installation and Con-
guration”.
RS485 and USB Connection (PTZ and Play Control)
Dome cameras
Recorder
Keyboard
Fig. 5-3
The domes are connected via the serial interface, the VSC-1 via the USB interface. The
conguration of the DNIs is not required.
For information for connection of the dome cameras via the serial interface refer to the
recorder’s and dome’s documentation “Installation and Conguration”.

VSC-1
www.dallmeier.com 17
5.1 Connection
WARNING
Electris shock!
Risk of serious injury.
Ensure that all components are disconnected from power supply before
connecting.
5.1.1 VSC-1 and Recorder via USB
The VSC-1 can be connected directly via a USB port to the recorder.
Connect the VSC-1 to a recorder’s USB interface using a USB cable.
Fig. 5-4
No further settings have to be made.
5.1.2 VSC-1 and Recorder via DNI
Use a two-wire line to connect the DNI and the VSC-1.
Connect . . .
. . . Tx1+ (VSC-1) to data input A RxD+ (DNI)
. . . Tx1- (VSC-1) to data input B RxD- (DNI)
+Tx1- +Tx2- +Tx3- +TRx1-+Tx1-
+TxD- GND +RxD-
Fig. 5-5 VSC-1 plug connector for serial Connection assignment DNI plug connector
interface

VSC-1
www.dallmeier.com 18
Plug connector
Fig. 5-6 DNI front view
For detailed information refer to the DNI-1 documentation “Installation and Conguration”.
5.1.3 DNI and Dome Camera
Use a two-wire line to connect the second DNI interface and the dome camera.
Rx+ (Dome) to data input A TxD+ (DNI)
Rx- (Dome) to data input B TxD- (DNI)
Set the ID number at the camera.
NOTICE
Potential malfunction of automatic camera switching!
The camera’s ID number must correspond to the respective video input on
the recorder.
Set the relevant protocol (Pelco-P) at the camera.
For detailed information refer to the documentation “Installation and Conguration” of the
respective camera manual.
5.1.4 Connection DNI and Recorder
Connect the DNI master to the recoder’s serial interface using a serial cable (RS232 with
1:1 assignment).
Fig. 5-7

VSC-1
www.dallmeier.com 19
5.1.5 Connection DNI network
Connect the DNI slaves with the DNI master and to each other using a CAT5 patch cable
via the network interface (RJ-45/RS485).
Fig. 5-8
5.2 Commissioning
When commissioning observe the following order:
Connect the DNI master to power supply if required.
Connect the dome camera to power supply.
Connect the VSC-1 to power supply.
Connect the recorder to power supply.
Start the recorder.

VSC-1
www.dallmeier.com 20
6 Conguration
The relevant monitor (VGA or CVBS) and the permission to use the VSC-1 can be set on
the recorder independent from the type of connection (DNI or USB).
Conguration of the serial interface and the DNI protocol is only required if a DNI is used.
Observer the recorder’s documentation “Installation and Conguration”.
Login at the recorder as Administrator.
6.1 Permissions on the Recorder
The permission OtherPermissions / Cameracontrol of the relevant user group has to be
activated separately in the UserManagement.
Selection and control of the camera is done on the control station, displaying of the images
on a recorder’s monitor. The VideoSystemController dialogue allows the specication
of the monitor and the split type that will be used. These settings are valid in every mode
(with or without login).
Additionally the dialogue allows the specication of the permission to use the control sta-
tion in Sequencer / Live mode (without login). This is done by adopting the permissions of
a user group.
Open the VideoSystemController dialogue via Setup > System > VSC.
Fig. 6-1
Set the relevant Monitor.
Set the Splittype.