Danfoss TP9 User manual

Fig.1
Space for additional
logo if required TP9
User Instructions
Fig.2
Before programming the thermostat press the + & – AND ▲& ▼ buttons
simultaneously to reset the unit (Fig.1)
Setting the Clock and Day
1) CLOCK - Press PROG (Fig.2) to begin programming
Use + or – buttons (Fig.3) to adjust the TIME (Fig.4)
2) DAY - Press PROG again(Fig.2)
Use + or – buttons (Fig.3) until correct DAY is shown (MO = Monday) (Fig.5)
Accepting the Factory Pre-settings
The TP9 has pre-set times already programmed in for controlling the heating
and hot water, which often suit most people (see Table below & Fig.12 over).
To accept these settings press the PROG button until the time appears in the
display and colon begins to flash - the unit is now in RUN mode (Fig.6).
If you wish to alter these settings follow instructions below.
Your installer will have set your unit to operate in one of the following modes:
5/2 day -one set of programmes for weekdays and another for weekends
24 hour - one set of programmes for the whole week
ProgrammingyourCENTRALHEATING
For Days 1-5 (weekdays)
a) Press PROG (Fig.2) 3 times to show the 1st pre-set time and temperature
(Event 1 Days 1,2,3,4,5) (Fig.7)
b) Use + or – buttons to adjust the TIME (press and hold to change in 10 min
increments)
c) Use ▲or ▼buttons to adjust the TEMPERATURE (Fig.8)
d) Press PROG (Fig.2) to move to next preset time & temp (Event 2) (Fig.9)
e) Repeat steps b, c & d for programming Events 3, 4 5 & 6
For Days 6-7 (weekends)
●Press PROG (Fig.2) to show 1st pre-set time and temperature (Event 1 Days
6-7) (Fig.10)
●Repeat steps b, c and d above to programme time and temperatyure
events for the weekend
NB. Left hand LED will be lit when the Central Heating programme is running
Fig.7
Fig.5
Fig.3
Fig.4
Fig.8
Mon-Sun (24 hour mode)
Mon-Fri (5/2 day mode) Sat-Sun (5/2 day mode)
Event Time Temp°C Event Time Temp°C
1 06.30 20 1 07.00 20
2 08.30 16 2 10.00 16
3 12.30 19 3 12.00 19
4 13.30 16 4 14.00 16
5 17.30 21 5 17.00 21
6 22.30 16 6 22.30 16 Fig.6
Fig.9
Fig.10

Danfoss Randall Ltd
Ampthill Road
Bedford, MK42 9ER
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.danfoss-randall.co.uk
Fig.15
Fig.12
Fig.13
Fig.11
For 24 hour mode (same set of programmes for each day of the week)
a) Press PROG (Fig 2) 3 times to show the 1st pre-set time and temperature
(Event 1) (Fig.11)
b) Use + or – buttons (Fig.3) to adjust the TIME (press and hold to change in
10 min increments)
c) Use ▲or ▼buttons (Fig.8) to adjust the TEMPERATURE
d) Press PROG (Fig.2) to move to next preset time & temperature (Event 2)
e) Repeat steps b, c & d for programming Events 3, 4 5 & 6
Programmingyour HOTWATER
To set the hot water programme press the PROG button (Fig.2) until Event A (1st
ON) appears on the display (Fig.13).
b) Use + or – buttons (Fig.3) to adjust the TIME (press and hold to change in 10
minute increments)
c) Use ▲or ▼buttons (Fig.8) to adjust the TEMPERATURE
d) Press PROG (Fig.2) to move to Event b - 1st OFF
e) Repeat steps b, c & d for programming Events C & d (2nd ON & 2nd OFF)
NB. Right hand LED will be lit when the Water programme is running
Returning to RUN mode
Press PROG until the colon in the LCD display starts to flash (Fig.14)
Temporary User Overrides
The TP9 has several useful overrides which can be selected without affecting
the thermostat programming
•Temporary override of programmed temperature – press ▲ or ▼ (Fig.8)
until required temperature is displayed (override will automatically cancel at
beginning of next programmed event)
•+1HR = if pressed while the programme is on, the hot water will remain on
for an extra hour. If it is pressed whilst the programme is off, the hot water
will come on immediately for 1 hour then go off (Fig.15)
•Frost Protection – a constant low temperature can be selected whilst away
from home - press ▲ ▲
▲ ▲
▲ & ▼ ▼
▼ ▼
▼ together (Fig.16) until display resembles (Fig.17)
•Hot Water only (during summer) - press ▲ ▲
▲ ▲
▲ & ▼ ▼
▼ ▼
▼ together (Fig.16) until
display resembles (Fig.18)
Summer Time / Winter Time Clock
•To change from Summer to Winter (clocks back) - press and hold - (Fig.19)
•Tochange fromWinter toSummer(clocks forward)- press andhold + (Fig.19)
Low Battery
If the unit is disconnected from the mains supply a low battery symbol will flash
in the LCD display (Fig.20). Programmes will be retained for 15 days. On the
16th day of continuous disconnection the display will show just a colon. When
powere is eventually restored your programmes will be remebered - you will
only need to reset the time and the day of the week.
Domestic Hot Water Times
Setting Function Pre-set
A On 6:30AM
b Off 8:30AM
C On 5:30PM
d Off 10:30PM
Fig.14
Fig.17
Fig.18
Fig.19
Fig.20
Clocksback
(Autumn)
Clocksforward
(Spring)
Fig.16