Datalogic Jet User manual

TECHNICAL FEATURES
Datalogic Jet™ Single Cradle Desk
Electrical Features
Power Supply* from 12 to 14 VDC± 5%
Consumption Max. 2.5 A
Indicators Power on LED (green)
Spare battery charge LED (bi-colored)
Charge Time Li-Ion Battery: max. 2.5 hours
Communication Features
Interface RS232, USB 1.1 version
Baud Rate RS232 = up to 115200 b/sec; USB = up to 12 Mb/sec
Environmental Features
Working Temperature** 0° to +50 °C / +32° to +140 °F
Storage Temperature -20° to +70 °C / -4° to +158 °F
Humidity 90% non condensing
Degree of Protection IP20
Mechanical Features
Dimensions 137 x 127 x 65 mm / 5.39 x 5 x 2.56 in
Weight (about) 500 g / 17.6 oz
* Recommended power supply: 94ACC4595 FPS18 W/O POWER CORD.
** Battery must be charged at a temperature ranging from 0° to +45 °C (+32° to +113 °F).
WEEE COMPLIANCE
822000572 (Rev. E)
Datalogic Jet™ Single Cradle Desk
The Datalogic Jet™ Single Cradle Desk paired with one Datalogic Jet™ PDA builds a Reading System for
the collection, decoding and transmission of barcoded data.
The communication between PDA and host PC through the Datalogic Jet™ Single Cradle Desk may
occur also by using the standard ActiveSync® connection.
Figure 1 – Datalogic Jet™ Single Cradle Desk
A) LED Indicators
B) PDA Contacts
C) Spare Battery Slot
D) USB Type B Connector
E) RS232 Connector
F) Power Jack
The Datalogic Jet™ Single Cradle Desk is a serial communication adapter between the host computer
and the Datalogic Jet™ PDA, and as such, no power supply is required to be connected to the Cradle for
communications.
Since the Datalogic Jet™ Single Cradle Desk also functions as a battery charger, a power supply is
required for battery recharging operations, both for PDA and spare battery pack recharging.
A
C
B
F
ED

By inserting the Datalogic Jet™ PDA into the cradle, data can be transmitted to the host and its battery
begins charging if the power supply is connected. In addition, an extra battery can be charged by inserting
it into the slot at the back of the Datalogic Jet™ Single Cradle Desk as shown in the following figure.
Figure 2 – Datalogic Jet™ Single Cradle Desk Charging
The LEDs positioned on the front part of the Datalogic Jet™ Single Cradle Desk (see figure below)
indicate the cradle and extra battery charger status:
Figure 3 - LED Indicators
LED STATUS
Charger Red Constant: charging
Green Constant: charge completed
Orange Blinking: error
Power Green: it is constant when the cradle is powered
The Datalogic Jet™ Single Cradle Desk can be connected to a host by means of an RS232 interface, or a
USB interface.
RS232 CONNECTION
A single Datalogic Jet™ Single Cradle Desk can be connected to the host by means of any standard null
modem cable. The 9-pin female D-Sub connector must be connected to the RS232 port of the cradle.
Once the host has been turned on, insert the Datalogic Jet™ PDA into the cradle.
Figure 4 - RS232 Connection
A) Host Computer B) Standard Null Modem Cable
C) Datalogic Jet™ Single Cradle Desk D) *Power Supply (only necessary for battery charging)
* Recommended power supply: 94ACC4595 FPS18 W/O POWER CORD.
USB CONNECTION
Datalogic Jet™ Single Cradle Desk can be connected to the host by means of a CAB-381 cable (USB
straight cord).
Once the host has been turned on, insert the Datalogic Jet™ PDA into the cradle.
Figure 5 - USB Connection
A) Host Computer B) 94A051550 CAB-381 USB Type A-B Straight Cable
C) Datalogic Jet™ Single Cradle Desk D) *Power Supply (only necessary for battery charging)
* Recommended power supply: 94ACC4595 FPS18 W/O POWER CORD.
Extra Battery
Charge Slot Data Transmission and
PDA Battery Charging
Extra Battery
Charger LED
Power LED
A
B
C
D*
A
B
C
D*