Datalogic Dragon User manual

DRAGON™
Reference Manual
90ACC1855
DLL6000-R/OM6010-R Compatibility
AUDIN - 7 bis rue de Tinqueux - 51100 Reims - France
Tel : [phone] - Fax : [phone]
Web : http: www.audin.fr - Email : [email protected]

Web : http: www.audin.fr - Email : [email protected]

DRAGON™
REFERENCE MANUAL
DLL6000-R/OM6010-R COMPATIBILITY
Web : http: www.audin.fr - Email : [email protected]

DATALOGIC S.p.A.
Via Candini 2
40012 - Lippo di Calderara di Reno
Bologna - Italy
DRAGON™ REFERENCE MANUAL
DLL6010-R/OM6010-R Compatibility
Ed.: 10/2002
This manual refers to
compatibility with DLL6010-R/OM6010-R
software version: SW 1.08
ALL RIGHTS RESERVED
Datalogic reserves the right to make modifications and improvements without prior notification.
Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor for incidental or
consequential damages resulting from the use of this material.
Product names mentioned herein are for identification purposes only and may be trademarks and or registered
trademarks of their respective companies.
© Datalogic S.p.A. 2002
Rev. A
Web : http: www.audin.fr - Email : [email protected]

iii
CONTENTS
HOW TO USE THIS MANUAL ......................................................... vi
1 INITIAL SETUP.................................................................................. 1
1.1 Set Compatibility................................................................................. 1
1.2 DLL6000-R/OM6010-R Compatibility SetUp...................................... 2
1.2.1 Using Multiple Guns With Same Cradle............................................. 5
1.2.2 Gun Default Configuration.................................................................. 6
1.2.3 Cradle Default Settings ...................................................................... 7
2 CONFIGURATION ............................................................................. 8
RS232 PARAMETERS..................................................................... 10
WEDGE PARAMETERS.................................................................. 14
PEN EMULATION PARAMETERS .................................................. 19
CRADLE OPERATING PARAMETERS........................................... 23
BATTERY CHARGING .................................................................... 26
NETWORK PARAMETERS ............................................................. 28
GUN OPERATING PARAMETERS ................................................. 31
READING PARAMETERS ............................................................... 35
DECODING PARAMETERS ............................................................ 39
GUN DISPLAY PARAMETERS ....................................................... 42
CODE SELECTION.......................................................................... 45
3 REFERENCES................................................................................. 55
3.1 RS232 Parameters........................................................................... 55
3.1.1 Handshaking .................................................................................... 55
3.1.2 Radio RX Lock ................................................................................. 55
3.1.3 RX Timeout ...................................................................................... 56
3.2 Wedge Parameters .......................................................................... 56
3.2.1 IBM AT - Alt Mode Interface............................................................. 56
3.2.2 Inter-character Delay........................................................................ 56
3.3 Pen EMULATION Parameters ......................................................... 57
3.3.1 Minimum Output Pulse ..................................................................... 57
3.3.2 Overflow ........................................................................................... 57
3.3.3 Output and Idle Levels ..................................................................... 58
3.4 Cradle and Gun Operating Parameters ........................................... 58
3.4.1 ACK from Host ................................................................................. 58
3.4.2 Radio Timeout .................................................................................. 59
Web : http: www.audin.fr - Email : [email protected]

iv
3.4.3 Output Data Format..........................................................................59
Header/Terminator Selection.........................................................60
Gun/Cradle Address Stamping......................................................61
Gun/Cradle Address Delimiter.......................................................61
Time Stamping Format ..................................................................61
Time Stamping Delimiter ...............................................................61
Code Identifier ...............................................................................62
3.5 Reading Parameters ........................................................................ 62
3.5.1 Trigger Signal ................................................................................... 62
3.5.2 Trigger Timeout................................................................................ 63
3.5.3 Reads per Cycle ............................................................................... 63
3.5.4 Safety Time ...................................................................................... 63
3.5.5 Single-Store...................................................................................... 63
3.5.6 Power-Off Timeout ........................................................................... 64
3.6 Decoding Parameters....................................................................... 64
3.6.1 Ink-Spread........................................................................................ 64
3.6.2 Overflow Control............................................................................... 65
3.6.3 Interdigit Control ............................................................................... 65
3.7 GUN Display Parameters ................................................................. 65
3.7.1 Display Mode.................................................................................... 65
3.8 Software Release ............................................................................. 66
4 COMMUNICATION AND MESSAGE FORMATTING.......................... 67
4.1 Messages from Host to Gun ............................................................ 67
4.1.1 Cursor Control .................................................................................. 68
4.1.2 Font Selection .................................................................................. 69
4.1.3 Clearing Display ............................................................................... 69
4.1.4 LED and Beeper Control ..................................................................70
4.1.5 Setting RTC...................................................................................... 70
4.2 Messages from Gun Command Keys .............................................. 71
A HOST CONFIGURATION STRINGS............................................... 73
B C6010 CONFIGURATION ............................................................... 82
C HEX AND NUMERIC TABLE........................................................... 83
Web : http: www.audin.fr - Email : [email protected]

v
HOW TO USE THIS MANUAL
This volume was written for the sole purpose of providing complete
configuration for DRAGON™ M readers and OM-DRAGON™ cradles used
as DLL6000-R/OM6010-R compatible readers and cradles for existing
DLL6000-R/OM6010-R applications.
If you are not using these products as DLL6000-R/OM6010-R
compatible readers/cradles, then use the Standard Reference Manual
for configuration.
Your DRAGON™ M/OM-DRAGON™ is supplied with its own Quick
Reference Manual which provides connection diagrams, reading diagrams,
basic application parameter settings, default values, and specific technical
features. You can use either your reader's Quick Reference Manual or this
Manual for initial configuration in order to set the default values and select
the interface for your application.
This manual can be used for complete setup and configuration of your
DRAGON™ M reader and OM-DRAGON™ cradle as DLL6000-R/OM6010-R
compatible products.
To use this manual for initial setup see chapter 1.
If you wish to change the default settings, this manual provides complete
configuration of your reader in an easy way.
To configure your reader:
1) Open the folded page in Appendix C with the hex-numeric table and
keep it open during the device configuration.
2) Read the Enter Configuration code ONCE, available at the top of
each page of configuration.
3) Modify the desired parameters in one or more sections following the
procedures given for each group.
4) Read the Exit and Save Configuration code ONCE, available at the
top of each page of configuration.
Web : http: www.audin.fr - Email : [email protected]

vi
Reference notes describing the operation of the more complex parameters
are given in chapter 3.
For communication between Host and gun, refer to chapter 4.
DL Sm@rtSet
DL Sm@rtSet is a Windows-based utility program providing a quick and
user-friendly configuration method via the RS232 interface.
It also allows upgrading the software of the connected device (see the DL
Sm@rtSet User's Manual for more details).
Sending Configuration Strings from Host
An alternative configuration method is provided in Appendix A using the
RS232 interface. This method is particularly useful when many devices need
to be configured with the same settings. Batch files containing the desired
parameter settings can be prepared to configure devices quickly and easily.
Web : http: www.audin.fr - Email : [email protected]

INITIAL SETUP
1
1
1 INITIAL SETUP
To start the system up, perform the operations represented in the flow-chart
below, following the given sequence.
Begin Setup by reading the Set
Compatibility code in par. 1.1
Follow the Compatibility Setup
procedure in par. 1.2
The system is ready to operate
according to the DLL6000-R/OM6010-R
default configurations
1.1 SET COMPATIBILITY
Set DLL6000-R compatibility
i#:+k
i#:+k
i#:+k
The reader will automatically be switched off and restarted and four high
tones will be emitted.
At this point, the DRAGON™ M scanner is ready to be configured using the
DLL6000-R procedure in par. 1.2.
To restore the DRAGON™ M standard configuration read the following code,
then follow the DRAGON™ M configuration procedure.
Restore DRAGON™ M standard configuration
i#:&k
i#:&k
i#:&k
Web : http: www.audin.fr - Email : [email protected]

DLL6000-R/OM6010-R COMPATIBILITY
2
1
1.2 DLL6000-R/OM6010-R COMPATIBILITY SETUP
When the cradle is connected and powered, configure the gun by reading the
following codes in the given sequence and follow the instructions.
Note: Open the folded page at the end of this Manual for the Numeric code
selections.
Restore DLL6000-R default
1. GcCgCmCgCjGgGjCgCgCgCjGgGgCjCgCjMcCcGjJcCcG
Default parameter settings are listed in par. 1.2.2.
Enter configuration
2. GcCgCmCgCjGgGjCgCgJcGgCgGjJcCcG
Set Date
3.
GcCgCmGjCcCjCjGcCjCcGgJgGjJcCcG
+
six digits for Day, Month and Year (DDMMYY).
Set Time
4.
GcCgCmGjCcCjCcGjCjGgCjCgGjJcCcG
+
four digits for Hours and Minutes (HHMM).
Set Gun Address
5.
GcCgCmGjCcCjCjGjCcCgGgJcGjJcCcG
+
three digits for the DLL6000-R Address (from 000 to 126).
All guns used in the same area must have different addresses.
Web : http: www.audin.fr - Email : [email protected]

INITIAL SETUP
3
1
Exit and Save configuration
6. GcCgCmCgCjGgCgGcJgGcGjGcGjJcCcG
7.
Read the Bind code to pair the DLL6000-R to the OM6010-R:
The reader is dedicated to the cradle. Any previously bound reader
will be excluded.
To connect several guns to the same cradle see the following
paragraph ‘Using Multiple Guns with Same Cradle'.
Bind
GcCgCmCgCjGgGjCgCgGjCcCjCcJjGcCgJcGgCgCjGgCgGcJgGjCgCgGjJcCcG
The green LED on the gun will blink: the scanner is ready to be
inserted into the cradle.
8.
Firmly insert the scanner into the cradle within 10 seconds, a beep
will be emitted, signaling that the cradle has been paired to the gun.
9.
Read the Restore Cradle default code
Restore Cradle default
GcCgCmCgCjGgGjCgCgGjCcCjJjCcGcCgJcGgCgCjGgCgGcJgGcJcCjGjJcCcG
Default parameter settings are listed in par.1.2.3.
Web : http: www.audin.fr - Email : [email protected]

DLL6000-R/OM6010-R COMPATIBILITY
4
1
10.
Read the Interface Selection code for your particular application:
RS232 Interface
GcCgCmCgCjGgGjCgCgCjCjGcJcJcGcCgJcGgCgCjGgCgGcJgCgCjGgGjJcCcG
PEN EMULATION
Interface
GcCgCmCgCjGgGjCgCgCjCjGcJcJcGcGgJcCgCgCjGgCgGcJgCjCcGjGjJcCcG
WEDGE Interface
IBM AT or PS/2 PCs
GcCgCmCgCjGgGjCgCgCjCjGcJcJcGcGcJgCgCgJcGgCgJcGgCgCjGgCgGcJgCgCcGmGjJcCcG
IBM AT - Alt Mode *
IBM XT
GcCgCmCgCjGgGjCgCgCjCjGcJcJcGcGcJgCgCgJcGgJcGcJcCgCjGgCgGcJgGjCgCgGjJcCcG
GcCgCmCgCjGgGjCgCgCjCjGcJcJcGcGcJgCgCgJcGgGgCcJgCgCjGgCgGcJgMcCgCgGjJcCcG
IBM SURE1
IBM Terminal 3153
GcCgCmCgCjGgGjCgCgCjCjGcJcJcGcGcJgCgCgJcGgGgJcCgCgCjGgCgGcJgCgCjGgGjJcCcG
GcCgCmCgCjGgGjCgCgCjCjGcJcJcGcGcJgCgCgJcGgGgCgJcCgCjGgCgGcJgCcCjMcGjJcCcG
IBM Terminals: 31xx, 32xx, 34xx, 37xx
KEY TRANSMISSION
make-only keyboard
or make-break keyboard
GcCgCmCgCjGgGjCgCgCjCjGcJcJcGcGcJgCgCgJcGgGgJgCcCgCjGgCgGcJgCjMcCcGjJcCcG GcCgCmCgCjGgGjCgCgCjCjGcJcJcGcGcJgCgCgJcGgCgJgGcCgCjGgCgGcJgCgGmCcGjJcCcG
KEYBOARD TYPE
advanced keyboard
GcCgCmCgCjGgGjCgCgCjGjCcCcGjJcCgJgGcCgCjGgCgGcJgJcCcMcGjJcCcG
typewriter keyboard
GcCgCmCgCjGgGjCgCgCjGjCcCcGjJcCgJcGgCgCjGgCgGcJgCcMjCcGjJcCcG
You can change any interface selection by simply reading another interface selection code.
RS232 and WEDGE interface selection codes automatically restore header and terminator
default values (see par. 3.4.3).
* See par. 3.2.1.
Web : http: www.audin.fr - Email : [email protected]

INITIAL SETUP
5
1
11. Test
CgCcGcGcCcGcCgCcCcGcCcGgCcCcGcGcGgCcCcCcCcCgGcCcGcGcCgGcCcCcCcGgGcCcCcCgCcGcGcCc
123456
Test O.K.: two short beeps
Test Failure: no beep or a long high-tone beep followed by a long
low-tone beep.
1.2.1 Using Multiple Guns With Same Cradle
If you want to use several guns associated with the same cradle, you must
first Bind the cradle with one of the guns (see the previously described
configuration procedure).
Successive guns can be associated with this same cradle by following the
configuration procedure substituting the Bind command with Join.
In this case the procedure ends with step
8 .
7.
Join
GcCgCmCgCjGgGjCgCgGjCcCjCcJjGcCgJgGcCgCjGgCgGcJgCgJcGgGjJcCcG
WARNING
If the cradle is not Bound to a gun, its address
assumes a random value which can cause conflicts
and malfunctions to other cradles within its range.
Web : http: www.audin.fr - Email : [email protected]

DLL6000-R/OM6010-R COMPATIBILITY
6
1
1.2.2 Gun Default Configuration
Reading Parameters
Trigger Signal level
Trigger Timeout 10 sec.
Reads per Cycle one
Safety Time .5 sec
Single-Store disabled
Power-off Timeout 8 hours
Beeper Intensity high
Beeper Tone 2
Good Transmission Beep enabled
Decoding Parameters
Ink Spread enabled
Overflow Control enabled
Interdigit Control enabled
Decoding Safety one read
Gun Operating Parameters
Code Identifier disabled
Time Stamping Format disabled
Time Stamping Delimiter none
ACK from Host disabled
* Radio Timeout 1/2 sec.
Display parameters
Font Size small
Display Timeout 8 sec.
Backlight off
Contrast normal
Display Mode normal
Code Selection
EAN 8/EAN 13 / UPC A/UPC E Check digit transmission, no conversions.
Interleaved 2/5 Check digit control and transmission,
variable length code: 4-99 characters.
Standard Code 39 No check digit control,
variable length code: 1-99 characters.
Code 128
Code 93; Codabar Disabled
* The restore default command does not affect the selection made for this parameter.
Web : http: www.audin.fr - Email : [email protected]

INITIAL SETUP
7
1
1.2.3 Cradle Default Settings
RS232 Parameters
Baud Rate 9600
Parity disabled
Data Bits 8
Stop Bit 1
Handshaking disabled
Radio RX Lock disabled
Inter-character Delay disabled
Rx Timeout 5 sec.
Pen Emulation Parameters
Conversion to Code 39 and
Code 128 Conversion to Code 39
Output Level normal
Idle Level normal
Minimum Output Pulse 600
µ s
Overflow medium
Wedge Parameters
Keyboard Nationality USA
Caps Lock off
Delays disabled
Num Lock off
Control Character Emulation Ctrl+Shift+Key
Cradle Operating Parameters
* Header none
* Terminator CR-LF (RS232), CR (Wedge)
Address Stamping disabled
Address Delimiter disabled
Battery Parameter
Battery Type auto-detect
Network Parameter
Echelon Network disabled
* The restore default command does not affect the selection made for these parameters.
Web : http: www.audin.fr - Email : [email protected]

DLL6000-R/OM6010-R COMPATIBILITY
8
2
2 CONFIGURATION
The DLL6000-R and OM6010-R default parameters can be changed by
following the procedure below.
1. Open the folded page in Appendix C with the Hex-Numeric table and
keep it open during configuration.
2. Go to the section of the group to modify.
3. Follow the procedure for that section.
System parameters are grouped according to the following figure:
Cra dle Pa ra me te rs
RS232
Parameters
WEDGE
Parameters
PEN Emulation
Parameters
Cradle Operating
Parameters Battery
Parameters
Network Parameters
G un Pa ra m e te rs
Reading
Parameters
Gun
Operating Parameters
Decoding
Parameters
Gun Display
Parameters
Code
Selection
Web : http: www.audin.fr - Email : [email protected]

9
CRADLE
PARAMETERS
Web : http: www.audin.fr - Email : [email protected]

10
RS232 PARAMETERS
= Choose only one code from each selected group
= Follow the procedure given for this code group
2.
Read configuration codes from the desired groups
1.
Read the Enter Configuration code ONCE, available at the top of each page.
3.
Read the Exit and Save Configuration code ONCE, available at the top of
each page.
TO CHANGE THE DEFAULT VALUES
PARAMETERS DEFAULT
9600
disabled
8
1
disabled
disabled
disabled
5 sec.
PARITY
DATA BITS
STOP BITS
HANDSHAKING
BAUD RATE
INTER-CHARACTER DELAY
RX TIMEOUT
RADIO RX LOCK
Web : http: www.audin.fr - Email : [email protected]

Enter configuration
ik
ik
RS232
Exit & Save configuration
i k
i k
11
BAUD RATE
150 baud
GcCgCmCjCjGcCcGjCjCgJcGgGcJcJcGjJcCcG 2400 baud
300 baud
GcCgCmCjCjGcCcGjCjGgCgJcCgCcGmGjJcCcG
GcCgCmCjCjGcCcGjCjCgJgGcJjCcGcGjJcCcG 4800 baud
600 baud
GcCgCmCjCjGcCcGjCjGcJgCgCmCgGcGjJcCcG
GcCgCmCjCjGcCcGjCjGgJgCcJjGcCcGjJcCcG 9600 baud
1200 baud
GcCgCmCjCjGcCcGjCjGgJcCgCgGcCmGjJcCcG
GcCgCmCjCjGcCcGjCjGgCcJgMjCcCcGjJcCcG 19200 baud
GcCgCmCjCjGcCcGjCjJcGcJcCmGgCcGjJcCcG
PARITY
disabled
GcCgCmCjCjGcCjCjGcCgJcGgGcJcCjGjJcCcG
even parity
odd parity
GcCgCmCjCjGcCjCjGcCgJgGcJcCcGjGjJcCcG
GcCgCmCjCjGcCjCjGcGgJgCcJcGcCjGjJcCcG
Web : http: www.audin.fr - Email : [email protected]

Enter configuration
ik
ik
RS232
Exit & Save configuration
i k
i k
12
DATA BITS
7 bits
GcCgCmCjCjGcCcCjGjCgJcGgCjJcGcGjJcCcG
8 bits
9 bits
GcCgCmCjCjGcCcCjGjCgJgGcGjCcJcGjJcCcG
GcCgCmCjCjGcCcCjGjGgJgCcGcJcJcGjJcCcG
STOP BITS
1 stop bit
GcCgCmCjCjGcCjCcGjCgJcGgGcCjJcGjJcCcG
2 stop bits
GcCgCmCjCjGcCjCcGjCgJgGcGcJjCcGjJcCcG
HANDSHAKING
disabled
GcCgCmCjCjGcCjGcCjCgJcGgJcCjGcGjJcCcG hardware (RTS/CTS)
software (XON/XOFF)
GcCgCmCjCjGcCjGcCjCgJgGcJcGjCcGjJcCcG
GcCgCmCjCjGcCjGcCjGgJgCcGgCmCcGjJcCcG RTS always ON
i$&Ak
i$&Ak
i$&Ak
See par. 3.1.1 for details.
Web : http: www.audin.fr - Email : [email protected]