DataStor Compaq Proliant Ultra2 SCSI III User manual

Packing List - Check Contents Prior To
Installation:
1) 1 - HD 68 pin Hot Plug Tray
2) 1 - 1.6” Tray Cover Grill
3) 1 - 1.0” Tray Cover Grill
4) 1 - Screw Pack
ElectrostaticDischarge
Manycomponentsonyourharddiskaresusceptible
to electrostatic discharge. To prevent damage to these
components, take careful precautions before handling
your hard disk.
CompatibilityDisclaimer
NOTE: This Hot Plug tray is only compatible with the
following models of Compaq
®
Proliant
TM
:
3000, 1600, 6000, 6500, 7000, 5500, 1600R,
1850R, 2500, 6200H, 1200, 850R
NOTE: Drives used with this Hot Plug tray should
be verified as compatible with one of the above
server models prior to attempting installation.
DriveTerminationWarning
NOTE: You MUST disable any automatic or
passive drive termination features on your hard
drive prior to using a drive in this tray.
RemoveCover Grill from Tray
1. Thiskitcomeswithtwo cover grills forthetray,
a 1”Low Profile cover, and a 1.6”Full Height
cover. Remove whichever of these two
covers is attached to the tray by sliding the
coverback and then liftingitup and awayfrom
thetray.
Install Drive into Tray
1. Make sure your drive is oriented correctly on
the tray so that the HD 68 pin connector side
of the drive is pointed toward the Rear of the
Tray. (Figure 2).
2. Fasten the drive to the bottom of the tray via
the four mounting holes (Figure 2).
Installation Guide
Compaq
®
ProliantTM Ultra2 / SCSI III 68pin Hot Plug Tray
(MORE)
Figure 2
Installation Guide - Hot Plug Tray, HD 68pin, Compaq Proliant , Rev 1.0 - March 1999 - P/N CQPTUWS
Compaq
®
and Proliant
TM
are both Trade Marks of Compaq Computer Corporation.
Figure 1
HD 68 Pin I/O
Connector
SCSI ID &
LED Block
Drive Power
Connector
Tray
Cover
Slots
(Both
Sides)
Drive Mount
Holes
Tray
Release Levers
Power, Activity,
and Error LED’s
Rear of Tray
(Connector)

ConnectTray Cables toDrive
NOTE: Please reference the documentation that came with your
hard drive for identification of proper connections on your drive.
1. Connect the HD 68pin I/O cable from the tray to the back of
thedrive.
2. Connectthe four-pin power connector tothebackofthe drive.
3. Connect the SCSI/Activity Jumper connector to the rear of
the drive. Orient the connector so that Pin 1 (The Red Wire
on the connector) orients with Pin 1 on the rear of your drive.
Normally, Pin 1 is the upper-right most pin on the rear of the
drive, and may be labeled “Pin 1”, “A0”, “ID 1”, “1-Signal”etc.
(See Figure 3 for Sample Configuration)
4. Referencing the documentation that came with your
drive, be sure to
Disable any automatic or passive drive
termination features on the drive itself.
NOTE:If you are unable to match the SCSI/Activity Jumper
connector to the drive, than your drive is NOT compatible with
this model of Compaq
®
Proliant
TM
.
Select and Attach Cover Grill to Tray
1. Select andattachthe appropriate covergrillto your tray. This
selection will depend on the format of drive you are using as
well as your current ProliantTM tray receiver configuration.
2. The cover grill attaches by inserting the four feet on the bottom of the cover through the Tray Cover Slots
(Figure 2) and then sliding the cover forward so that the front, beveled part of the cover is flush with the
beveled portion of the tray.
3. The cover can be further secured by mounting two screws through the side mounting holes on the sides of
the cover to the appropriate mounting holes in your drive, if available.
Insert Tray into Receiving Cage
1. Referencing Figure Four, apply pressure between your thumb and forefinger on the tray release levers on
the front of the tray. This should allow the levers to swing out, thus allowing you to slide the tray into the
receiver on your server.
2. Gently slide the tray into the receiver until you feel the PCB connector on the back of the tray touch the
connector.
3. Rotate the Release Levers back into the locked position. You should hear and feel a click when the levers
lockintoplace. This should force the tray completely into the receiver connector and snugly lock the tray into
the server.
Figure 3
Copyright1999byDataStor,Inc. Allrightsreserved. NopartofthisdocumentmaybereproducedinanyformwithoutpriorwrittenconsentfromDataStor. Theinformationandspecificationsinthisdocumentaresubjecttochange
withoutnotice. Changestothisdocumentareincorporatedinnewversions. DataStor,andtheDataStorlogoarereqisteredtrademarksofDataStor,Inc. Othertrademarksusedhereinarethepropertyoftheirrespectiveowners.
ThisdocumentwasprintedintheUnitedStatesOfAmerica.
DataStor, 12601 Monarch Street, Garden Grove, CA 92841-3918
Phone [phone] / Fax: [phone] / Web Site: www.dstor.com
Figure 7
Figure 4 TrayRelease Levers
Close-Up View
SCSI/ActivityJumper
Configuration
Pin 1 (Red Wire)
DriveJumper Block
TraySCSI
Activity
Connector
Installation Guide - Hot Plug Tray, HD 68pin, Compaq Proliant , Rev 1.0 - March 1999 - P/N CQPTUWS
Compaq
®
and Proliant
TM
are both Trade Marks of Compaq Computer Corporation.