DataStor Compaq Proliant Ultra2 SCA User manual

PackingList-CheckContentsPriorToInstallation:
1) 1 - SCA 80 pin Hot Plug Tray
2) 1 - 1.6” Tray Cover Grill
3) 1 - 1.0” Tray Cover Grill
4) 1 - Screw Pack
ElectrostaticDischarge
Manycomponentsonyour harddisk aresusceptible
to electrostatic discharge. To prevent damage to these
components, take careful precautions before handling
your hard disk.
CompatibilityDisclaimer
NOTE: This Hot Plug tray is only compatible with the
following models of Compaq
®
Proliant
TM
:
3000, 1600, 6000, 6500, 7000, 5500, 1600R,
1850R, 2500, 6200H, 1200, 850R
NOTE: Drives used with this Hot Plug tray should
be verified as compatible with one of the above
server models prior to attempting installation.
DriveTerminationWarning
NOTE: You MUST disable any automatic or
passive drive termination features on your hard
drive prior to using a drive in this tray.
RemoveCoverGrill from Tray
1. Thiskitcomes with twocover grills forthe tray,
a 1”Low Profile cover, and a 1.6”Full Height
cover. Remove whichever of these two
covers is attached to the tray by sliding the
coverback and thenlifting it upandaway from
thetray.
Install Drive into Tray
1. Make sure your drive is oriented correctly on
the tray so that the SCA 80pin connector side
of the drive is pointed toward the Rear of the
Tray. (Figure 2).
2. Fasten the drive to the bottom of the tray via
the four mounting holes (Figure 2).
Installation Guide
Compaq
®
ProliantTM Ultra2 SCA 80pin Hot Plug Tray
(MORE)
Figure 2
Installation Guide - Hot Plug Tray, Ultra2 SCA 80pin, Compaq Proliant , Rev 1.0 - August 1999 - P/N CQPTSCA
Compaq
®
and Proliant
TM
are both Trade Marks of Compaq Computer Corporation.
Figure 1
SCA 80pin
Connector
Tray
Cover
Slots
(Both
Sides)
Drive Mount
Holes
Tray
Release Levers
Power, Activity,
and Error LED’s
Rear of Tray
(Connector)

ConnectDrivetoSCA 80pin connector
1. Connect the SCA 80pin connector on your drive to the SCA
80pin connector in the tray
2. Referencing the documentation that came with your
drive, be sure to
Disable any automatic or passive drive
termination features on the drive itself.
Select and Attach Cover Grill to Tray
1. Select andattachthe appropriate covergrillto your tray. This
selection will depend on the format of drive you are using as
well as your current ProliantTM tray receiver configuration.
2. The cover grill attaches by inserting the four feet on the
bottom of the cover through the Tray Cover Slots (Figure 2) and then sliding the cover forward so that the
front, beveled part of the cover is flush with the beveled portion of the tray.
3. The cover can be further secured by mounting two screws through the side mounting holes on the sides of
the cover to the appropriate mounting holes in your drive, if available.
Insert Tray into Receiving Cage
1. Referencing Figure Four, apply pressure between your thumb and forefinger on the tray release levers on
the front of the tray. This should allow the levers to swing out, thus allowing you to slide the tray into the
receiver on your server.
2. Gently slide the tray into the receiver until you feel the PCB connector on the back of the tray touch the
connector.
3. Rotate the Release Levers back into the locked position. You should hear and feel a click when the levers
lockinto place. This should force thetray completelyinto the receiver connector andsnugly lockthe tray into
the server.
Copyright1999byDataStor,Inc. Allrightsreserved. NopartofthisdocumentmaybereproducedinanyformwithoutpriorwrittenconsentfromDataStor. Theinformationandspecificationsinthisdocumentaresubjecttochange
withoutnotice. Changestothisdocumentareincorporatedinnewversions. DataStor,andtheDataStorlogoarereqisteredtrademarksofDataStor,Inc. Othertrademarksusedhereinarethepropertyoftheirrespectiveowners.
ThisdocumentwasprintedintheUnitedStatesOfAmerica.
DataStor, 12601 Monarch Street, Garden Grove, CA 92841-3918
Phone [phone] / Fax: [phone] / Web Site: www.dstor.com
Figure 7
Figure 3 TrayRelease Levers
Close-Up View
Installation Guide - Hot Plug Tray, Ultra2 SCA 80pin, Compaq Proliant , Rev 1.0 - August 1999 - P/N CQPTSCA
Compaq
®
and Proliant
TM
are both Trade Marks of Compaq Computer Corporation.