Datastor Dt51uws-p User manual

Installation Guide

Packing List - Check Contents Prior To Installation:

1) 1 - 5.25" Plastic 68pin Frame

2) 1 - 3.5" Plastic 68pin Tray

3) 1 - Screw/Key Pack

3) 1-Installation Guide

Electrostatic Discharge

Many components on your hard disk are susceptible to electrostatic

discharge. To prevent damage to these components, take careful

precautions before handling your hard disk.

Remove the Casing for your Tower/Enclosure

1. Unplug the computer, as well as all peripheral devices and cables.

2. Referring to the owner's manual for your computer or enclosure,

remove the outer casing.

3. Referring to the owner's manual for your computer or enclosure,

removeanyfrontpanelorbezel onthe5.25"bay youplanoninstalling

your tray & frame in.

Install the Frame

1. Place the Frame into the 5.25" Bay with the backplane of the Frame

toward the rear of the bay. To determine which side of your frame is

the top, view the frame from the back (Figure 2) if the fan is on the

left side, you are holding the frame right side up.

2. Line up the four bracket holes in the frame with the corresponding

holesin your 5.25" bay. Using the screwswhich can be foundinside

of your tray (along with the keys to the tray lock), fasten the frame

into the bay.

3. With the frame securly fastened, slide the tray into the

frame to ensure that the tray fits snugly but smoothly

into the frame. Be sure that the tray is right side up by

viewing the front (handle side) of the tray. If the tray is

right side up, the lock will be visible on the right side of

the tray. As the tray is slid into the frame, apply even

pressure to both sides of the tray to ensure a proper

connection.

4. Removethe traybygentlylifting ontheFORCE-LESSTM

handleuntilthe tray is dislodged from the frame. Then,

gently pull on the tray with the handle until the tray is

completely removed from the frame assembly.

Make Wire Connections Between Frame and Enclosure

1. With the frame mounted in the enclosure, turn the

enclosure so that you have a clear view of the

backplane of the frame. Connect the 68 pin HDD

controller cable and the power cable.

SCSI III 68pin Removable Tray & Frame, Plastic

Figure 1

Top

Bottom

Figure 2

2. Referring to Figure 3, as well as the documentation

provided with your enclosure, connect the SCSI ID

cables to the five connectors as shown in Figure 3.

Installation Guide - DataTrans 68 pin Plastic Removable Tray&Frame, Rev 1.0 - July 1998 - P/N DT51UWS-P

(MORE)

Figure 3 68 pin HDD

Controller Power

Connector

8 Signal8 Signal

8 Signal

4 Signal4 Signal

4 Signal

2 Signal2 Signal

2 Signal

1 Signal1 Signal

1 Signal

GroundGround

Ground

Install Hard Drive into tray

NOTE: Please reference the documentation that came with your

hard drive for diagrams which show the SCSI pin location(s) on

yourdrive.

1. Open your DataTrans tray by gently pulling the “open” tab on

the cover of the tray away from the tray side and then slide

the cover toward the rear of the tray. You will find the tab on

the front left corner of the tray cover.

2. Inside your tray you will find several sets of cabling, including

afour-pinpowerconnector,a 68pin HDD controller connector,

a set of 5 wires for SCSI ID, and a set of two wires for the

Drive Activity LED (See Figure 4).

3. Referencing the manual that came with your drive, plug the

SCSI ID cables into the back of the drive. Figure 5 provides a

nomenclature color diagram for the SCSI ID cabling inside

the tray. Figure 6 provides a sample jumper configuration

4. Ifyou desire, plugtheDrive Activity Cable into theappropriate

connector on your drive.

5. Plugthe four-pinpowerconnector andthe68pinHDD controller

connector into the drive.

6. Mount the drive into the tray using the four screws provided.

7. Replace the cover by following the reverse procedure for

removing it in step 1.

Install Tray into Frame

1. Prior to replacing the cover on your enclosure, be sure to set

your SCSI ID using the rotary switch located on the bottom

rightof the tray(Figure 7). Do not confusethe SCSI IDcables

with the Drive Activity Cable, which is a paired cable on the

same terminal which consists of one Black wire and one Red

wire (Red is signal, Black is ground).

2. Insert a key from the set provided into your tray lock, and turn

the key counter clockwise to lock the tray - the drive is now

ready to receive power, and should power up normally when

your system is on.

Replace Enclosure Cover

1. Followingthe documentation providedby the manufacturer of

your enclosure, replace the cover of the enclosure.

Figure 4 Wiring (Inside Tray)

Copyright1999byDataStor,Inc. Allrightsreserved. NopartofthisdocumentmaybereproducedinanyformwithoutpriorwrittenconsentfromDataStor. Theinformationandspecificationsinthisdocumentaresubjecttochangewithout

notice. Changestothisdocumentareincorporatedinnewversions. DataStor,andtheDataStorlogoarereqisteredtrademarks ofDataStor,Inc. Othertrademarksusedhereinarethepropertyoftheirrespectiveowners. Thisdocument

wasprintedintheUnitedStatesOfAmerica.