Supermicro 6038R-DE2CR16L User manual

USER’S MANUAL
1.0a
SUPER STORAGE SYSTEM
6038R-DE2CR16L

iii
Preface
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the 6038R-DE2CR16L. Instal-
lation and maintainance should be performed by experienced technicians only.
The 6038R-DE2CR16L is a high-end storage server solution based on the SC937
3U rackmount chassis and the X10DRS dual processor serverboard.
Manual Organization
Chapter 1: Introduction
The rst chapter provides a checklist of the main components included with the
server system and describes the main features of the X10DRS serverboard and
the SC937ETS-R1200NDBP chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the 6038R-DE2CR16L into a
rack and check out the server conguration prior to powering up the system. If your
server was ordered without processor and memory components, this chapter will
refer you to the appropriate sections of the manual for their installation.
Chapter 3: System Interface
Refer here for details on the system interface, which includes the functions and
information provided by the control panels on the chassis as well the HDD carrier
LEDs.
Chapter 4: Standardized Warning Statements
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
6038R-DE2CR16L.
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu-
mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harm-
ful interference, in which case you will be required to correct the interference at your own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn-
ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro-
ductive harm.
Manual Revision 1.0a
Release Date: May 20, 2016
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America

SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
iv
Notes
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X10DRS serverboard, including the
locations and functions of connections, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconguring the
serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC937 server chassis. You should
follow the procedures given in this chapter when installing, removing or recongur-
ing SAS/SATA or peripheral drives and when replacing system power supply units
and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed informa-
tion on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: System Specications
Preface
v

vi
Table of Contents
Chapter 1 Introduction
1-1 Overview ......................................................................................................... 1-1
1-2 Serverboard Features ..................................................................................... 1-2
Processors ...................................................................................................... 1-2
Memory ........................................................................................................... 1-2
SAS Disk Controller ........................................................................................ 1-2
SAS Expander................................................................................................. 1-2
SATA .............................................................................................................. 1-2
NTB Connectivity ............................................................................................ 1-2
PCI Expansion Slots ....................................................................................... 1-3
Rear Chassis Ports ......................................................................................... 1-3
Graphics Controller ......................................................................................... 1-3
1-3 Server Chassis Features ................................................................................ 1-3
System Power................................................................................................. 1-3
SAS Subsystem .............................................................................................. 1-3
Front Control Panel......................................................................................... 1-3
Cooling System............................................................................................... 1-3
1-4 Contacting Supermicro.................................................................................... 1-5
1-5 SBB: Storage Bridge Bay ............................................................................... 1-6
Chapter 2 Server Installation
2-1 Overview ......................................................................................................... 2-1
2-2 Unpacking the System .................................................................................... 2-1
2-3 Preparing for Setup......................................................................................... 2-1
Choosing a Setup Location............................................................................. 2-1
2-4 Warnings and Precautions.............................................................................. 2-2
Rack Precautions............................................................................................ 2-2
Server Precautions.......................................................................................... 2-2
Rack Mounting Considerations ....................................................................... 2-3
Ambient Operating Temperature ................................................................ 2-3
Reduced Airow ......................................................................................... 2-3
Mechanical Loading ................................................................................... 2-3
Circuit Overloading..................................................................................... 2-3
Reliable Ground ......................................................................................... 2-3
2-5 Installing the System into a Rack ................................................................... 2-4
Installing the Inner Rack Rails ........................................................................ 2-4
Installing the Outer Rack Rails ....................................................................... 2-5
Installing the Chassis into a Rack................................................................... 2-6
vii
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
Chapter 3 System Interface
3-1 Overview ......................................................................................................... 3-1
3-2 Control Panel Button....................................................................................... 3-1
Power .............................................................................................................. 3-1
3-3 Control Panel LEDs ........................................................................................ 3-1
Power Fail ....................................................................................................... 3-1
Overheat/Fan Fail: .......................................................................................... 3-2
NIC1 ................................................................................................................ 3-2
NIC2 ................................................................................................................ 3-2
Heartbeat......................................................................................................... 3-2
Power .............................................................................................................. 3-3
3-4 Drive Carrier LEDs.......................................................................................... 3-3
Chapter 4 Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements....................................................... 4-1
Warning Denition ........................................................................................... 4-1
Installation Instructions.................................................................................... 4-4
Circuit Breaker ................................................................................................ 4-5
Power Disconnection Warning........................................................................ 4-6
Equipment Installation..................................................................................... 4-8
Restricted Area................................................................................................ 4-9
Battery Handling............................................................................................ 4-10
Redundant Power Supplies .......................................................................... 4-12
Backplane Voltage ........................................................................................ 4-13
Comply with Local and National Electrical Codes........................................ 4-14
Product Disposal........................................................................................... 4-15
Hot Swap Fan Warning................................................................................. 4-16
Power Cable and AC Adapter ...................................................................... 4-18
4-2 Presence Condition of the Restricted Substances Marking ......................... 4-20
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard ............................................................................... 5-1
Precautions ..................................................................................................... 5-1
5-2 Cable and Device Connectiions...................................................................... 5-2
Power Connections .................................................................................... 5-2
Fan Cabling................................................................................................ 5-2
Control Panels............................................................................................ 5-2
5-3 Installing the Processor and Heatsink ............................................................ 5-3
Installing an LGA2011 Processor.................................................................... 5-3
Installing a CPU Heatsink ............................................................................... 5-6
Removing the Heatsink................................................................................... 5-6
Table of Contents

viii ix
5-4 Installing Memory............................................................................................ 5-7
Memory Support.............................................................................................. 5-7
DIMM Installation ............................................................................................ 5-7
5-5 Installing PCI Add-On Cards........................................................................... 5-9
5-6 Serverboard Details ...................................................................................... 5-10
X10DRS Quick Reference .............................................................................5-11
5-7 Connector and Port Denitions .................................................................... 5-12
5-8 Jumper Settings ............................................................................................ 5-14
5-9 Onboard Indicators........................................................................................ 5-16
5-10 Serial ATA Ports ............................................................................................ 5-17
5-11 Installing Software......................................................................................... 5-18
SuperDoctor® 5 ............................................................................................ 5-19
5-12 Onboard Battery............................................................................................ 5-20
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices.................................................................................. 6-1
Precautions ..................................................................................................... 6-1
Unpacking ....................................................................................................... 6-1
6-2 Control Panel .................................................................................................. 6-2
6-3 System Fans ................................................................................................... 6-2
System Fan Failure......................................................................................... 6-3
Replacing System Fans .................................................................................. 6-3
6-4 Drive Bay Installation/Removal ....................................................................... 6-5
Accessing the Drive Bays ............................................................................... 6-5
Hard Drive Midplane ....................................................................................... 6-5
SAS 3.0 Controller .......................................................................................... 6-5
SAS Drive Installation ..................................................................................... 6-5
6-5 Midplane.......................................................................................................... 6-8
6-6 Power Supply.................................................................................................. 6-9
Power Supply Failure...................................................................................... 6-9
Replacing the Power Supply........................................................................... 6-9
Chapter 7 BIOS
7-1 Introduction...................................................................................................... 7-1
Starting BIOS Setup Utility.............................................................................. 7-1
How To Change the Conguration Data ......................................................... 7-1
How to Start the Setup Utility ......................................................................... 7-2
7-2 Main Setup...................................................................................................... 7-2
7-3 Advanced Setup Congurations...................................................................... 7-4
7-4 Event Logs .................................................................................................... 7-32
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
7-5 IPMI............................................................................................................... 7-34
7-6 Security Settings ........................................................................................... 7-36
7-7 Boot Settings................................................................................................. 7-39
7-8 Save & Exit ................................................................................................... 7-41
Appendix A BIOS Error Beep Codes
Appendix B System Specications
Table of Contents

SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
x
Notes

Chapter 1
Introduction
1-1 Overview
The 6038R-DE2CR16L is a high-end Super Storage Bridge Bay (SBB) system
comprised of two main subsystems: the SC937ETS-R1200NDBP chassis and two
X10DRS dual processor serverboards. Please refer to our website for informa-
tion on operating systems that have been certied for use with the system (www.
supermicro.com).
In addition to the serverboard and chassis, various hardware components have
been included with the 6038R-DE2CR16L, as listed below. Quantities indicate the
number included in the whole system (two nodes).
• Four passive CPU heatsinks (SNK-P0048PS)
• Twelve sets of counter-rotating 4-cm fans (FAN-0157L4)
• SAS/SATA Accessories
One SAS midplane (BPN-SAS3-937)
Sixteen hard drive carriers (MCP-220-93703-0B)
• Two riser cards for PCI-Express 3.0 expansion cards (RSC-R2US-3E8R)
• Two SAS controller mezzanine cards (one per node) (AOM-S3008-L8-SB)
• One set of rackmount hardware (MCP-290-00057-0N)
Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.
• Supermicro product manuals: http://www.supermicro.com/support/manuals/
• Product drivers and utilities: ftp://ftp.supermicro.com
• Product safety info: http://www.supermicro.com/about/policies/safety_informa-
tion.cfm
• If you have any questions, please contact our support team at:
[email protected]m
Chapter 1: Introduction
1-1

1-2 1-3
Chapter 1: Introduction
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
1-2 Serverboard Features
The 6038R-DE2CR16L is built around two X10DRS serverboards for a dual-node
system that shares storage resources as well as features a dedicated PCI-E bus
between server nodes for High Availability (HA), Cluster in a Box (CiB) applications
The X10DRS is a dual processor serverboard based on the Intel® PCH C612
chipset. Below are the main features of the X10DRS. (See Figure 1-1 for a block
diagram of the chipset).
Processors
The X10DRS supports single or dual Intel® Xeon E5-2600 v3/v4 series processors
in LGA 2011 R3 type sockets. Two X10DRS boards are included in the storage
system. Please refer to the serverboard description pages on our website for a
complete listing of supported processors (www.supermicro.com).
Memory
Each X10DRS has eight DIMM slots that can support up to 1 TB of LRDIMM (Load
Reduced) or 512 GB of Registered (RDIMM) ECC DDR4-2400/2133/1866/1600
memory. See Chapter 5 for details.
SAS Disk Controller
Two external SAS 3.0 ports are supported by a disk controller on a mezzanine
included on each X10DRS (for a total of four in the system).
SAS Expander
An IR mode SAS controller is located on a mezzanine card included in each of the
server nodes. One 40-port SAS expander is integrated into each X10DRS board.
SATA
Each X10DRS has two SATA 3.0 ports with power headers to support two SATA
Disk-on-Module (SATA DOM) devices per node. RAID 0 and 1 are supported by
the PCH.
NTB Connectivity
Non Transparent Bridge connectivity featuring 8 lanes of PCI-E 3.0 between server
nodes.
PCI Expansion Slots
Each X10DRS features one PCI-E 3.0 x24 slot for riser card support.
Rear Chassis Ports
The rear of each serverboard includes two mini SAS HD ports, two 10 Gb Ethernet
ports and a KVM connector (includes USB, VGA and COM ports).
Graphics Controller
The X10DRS features an integrated ASpeed AST 2400 BMC video controller.
1-3 Server Chassis Features
System Power
The 6038R-DE2CR16L features a redundant Titanium Level 1200W power supply
composed of two separate power modules. This power redundancy feature allows
you to replace a failed power module without shutting down the system.
SAS Subsystem
The 6038R-DE2CR16L supports up to 16 3.5" SAS drives. These drives are
hot-swappable units and are connected to a midplane that provides power and
control.
Front Control Panel
Two control panels are included on each end of the 6038R-DE2CR16L to provide
you with system monitoring and control. LEDs indicate system power, network (NIC)
activity, system overheat and power supply failure. Each set of LEDs are associated
with the node/serverboard on the same side of the chassis. A single power button
is located on the right side control panel. When pressed, both nodes will power on
or off according to the BIOS setup settings.
Cooling System
The SC937ETS-R1200NDBP chassis has 12 back-to-back, 4-cm counter-rotating
fans: three at the front and another three at the rear of each node. This counter-
rotating action works to dampen vibration levels while generating exceptional airow.
Each power supply module also includes a cooling fan.

1-4 1-5
Chapter 1: Introduction
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
Figure 1-1. Intel C602J Chipset:
System Block Diagram
Note: This is a general block diagram and may not exactly represent the features
on your motherboard. Please see Chapter 5 for details.
1-4 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [email protected] (General Information)
[email protected] (Technical Support)
[email protected] (Customer Support)
Asia-Pacic
Address: Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 23511
Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [email protected]
Tel: [phone]
PE1B[7..4]
PE2A[15..0] PE3A[7..0]
PE3C[15..8]
PCIe GEN3 16-lane
PCI-E X8
USB 0,1
VGA
BMC
COM1 External
VGA CONN
USB 0-1
JKVM
BMC ETH DATA LINK
LPC
TPM HDR
USB
USB TypeA
SATA0
AIRMAX SBB MIDPLANE
DUAL-PORTED
SAS DRIVES
PE2C [15:8]
PE3A[3:0]
MEZZANINE
LSI3008
8 PORTS
RJ45 LAN1
10G LAN
X540
PE3B[7:4]
PE1A[3..0]
PCI-E X8
PCI-E G2 X8
PCI-E X24 230 PINS
LSI SASX40
24 PORTS:PHY12~27
SAS3 EXPD
EXT1
EXT0
PEX
8717
NTB X8
SAS3
REDRIVER
M1
FRONT
PANEL
PWR
SWAP
BACK PLANE
POWER
GPIO
LED
E
F
G
1#UPC2#UPC
A
B
C
DDR4 DIMM
DDR4 DIMM
P0
QPI 9.6G
P1
DDR4
DMI2
DMI2
SFF-8644
SFF-8644
RJ45 LAN2
SATA1
4 PORTS:PHY4~7
4 PORTS:PHY8~11
COM1
COM2
COM1
COM2
D
H
1333/2133
1333/2133
1P0P QPI 9.6G
5 PHASE
145W
VR12.5
PCH
6.0
Gb/S
USB
USB 2.0
AST2400
PHY
RTL8211E-VB-CG
NVME 4 PORTs
M7
:PHY32~39
8 PORTS:PHY0~3
PHY28~31
DDR4
X4
X4
MUX
SPI
BIOS
SPI
MUX
PCIeX1 Gen2
USB2.0
DDR3
RMII/NCSI
RMII/NCSI
PE3C [8]
100M LAN
I-210
PCI-E G1 X1
5 PHASE
145W
VR12.5
PE3CD [15:8]
6.0
Gb/S
(SATA0/1: SATA DOM supported)
Connector
PE2A[7:0]
3.0
PE2A[0,1; 4,5; 8,9; 12,13] for NEME
PE2A[2,3; 6,7; 10,11; 14,15] for Empty

1-6
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
1-5 SBB: Storage Bridge Bay
The 6038R-DE2CR16L Super SBB was designed to function as a fully redundant,
fault-tolerant "cluster-in-a-box" system. The standard support for 16 3.5" hot-swap
HDDs (SAS2 or SAS3) may be expanded to support additional storage with the
optional SBB JBOD SSG-937R-E2CJB conguration.
The Super SBB provides hot-swappable canisters for all active components. Each
of the two serverboard canisters support dual-processors, 8 DIMM slots, 3 PCI-E
Gen3 slots and 12 Gbps SAS (SAS3). The 6038R-DE2CR16L features eight lanes
of PCI-E 3.0 connecting the left server module with the right server module. This
connection is used for high speed data transfers between nodes for High Avail-
ability/server fail-over. This fail-over capability is fully dependent on the software/
OS installed and how the chosen software uses the connection (Active-Active or
Active-Passive). 6038R-DE2CR16L hardware is supplied without a storage OS or
fail-over software.
Equipped with 1200W 80PLUS Titanium Level redundant power supplies and re-
dundant cooling fans, the 6038R-DE2CR16L offers fully redundant high-availability
while maintaining energy efcient operation.

Chapter 2: Server Installation
2-1
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get the 6038R-DE2CR16L up and
running. Following these steps in the order given should enable you to have the
system operational within a minimum amount of time. This quick setup assumes
that your system has come to you with the processors and memory preinstalled. If
your system is not already fully integrated with a serverboard, processors, system
memory etc., please turn to the chapter or section noted in each step for details on
installing specic components.
2-2 Unpacking the System
You should inspect the box the 6038R-DE2CR16L was shipped in and note if it was
damaged in any way. If the server itself shows damage you should le a damage
claim with the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the 6038R-DE2CR16L.
It should be situated in a clean, dust-free area that is well ventilated. Avoid areas
where heat, electrical noise and electromagnetic elds are generated. You will also
need it placed near a grounded power outlet. Read the Rack and Server Precau-
tions in the next section.
2-3 Preparing for Setup
The box the 6038R-DE2CR16L was shipped in should include two sets of rail
assemblies, two rail mounting brackets and the mounting screws you will need to
install the system into the rack. Follow the steps in the order given to complete the
installation process in a minimum amount of time. Please read this section in its en-
tirety before you begin the installation procedure outlined in the sections that follow.
Choosing a Setup Location
• Leave enough clearance in front of the rack to enable you to open the front door
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for sufcient airow and ease in servicing.

Chapter 2: Server Installation
2-32-2
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
• This product is for installation only in a Restricted Access Location (dedicated
equipment rooms, service closets and the like).
• This product is not suitable for use with visual display work place devices
acccording to §2 of the the German Ordinance for Work with Visual Display Units.
2-4 Warnings and Precautions
Rack Precautions
• Ensure that the leveling jacks on the bottom of the rack are fully extended to
the oor with the full weight of the rack resting on them.
• In single rack installation, stabilizers should be attached to the rack. In multiple
rack installations, the racks should be coupled together.
• Always make sure the rack is stable before extending a component from the
rack.
• You should extend only one component at a time - extending two or more si-
multaneously may cause the rack to become unstable.
Server Precautions
• Review the electrical and general safety precautions in Chapter 4.
• Determine the placement of each component in the rack before you install the
rails.
• Install the heaviest server components on the bottom of the rack rst, and then
work up.
• Use a regulating uninterruptible power supply (UPS) to protect the server from
power surges, voltage spikes and to keep your system operating in case of a
power failure.
• Allow any hot plug drives and power supply modules to cool before touching
them.
• Always keep the rack's front door and all panels and components on the servers
closed when not servicing to maintain proper cooling.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating tempera-
ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera-
ture (Tmra).
Reduced Airow
Equipment should be mounted into a rack so that the amount of airow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec-
tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:
• This unit should be mounted at the bottom of the rack if it is the only unit in
the rack.
• When mounting this unit in a partially lled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, install the stabilizers before
mounting or servicing the unit in the rack.

Chapter 2: Server Installation
2-52-4
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
2-5 Installing the System into a Rack
This section provides information on installing the SC937 chassis into a rack unit
with the quick-release rails provided. There are a variety of rack units on the market,
which may mean the assembly procedure will differ slightly. You should also refer to
the installation instructions that came with the rack unit you are using.
Installing the Inner Rack Rails
Installing the Inner Rails
1. Extend the inner rail toward the front of the rail assembly as far as possible,
then depress the locking tab to pull it completely out.
2. Place the inner rail on the side of the chassis aligning the hooks of the chas-
sis with the rail extension holes.
3. Slide the extension toward the front of the chassis.
4. You may secure the chassis with screws if desired.
5. Repeat steps 1-3 for the other inner rail.
Figure 2-1. Installing the Outer Rack Rails
1
2
1
3
Figure 2-2. Outer Rack Rails
Figure 2-3. Outer Rack Rail Install
Installing the Outer Rack Rails
Outer rails attach to the server rack and hold the server in place. The outer rails for
the SC937 chassis extend between 30 inches and 33 inches.
Installing the Outer Rails
1. Attach the right outer rail to the rack by inserting the hooks included on the
rails into the holes provided on the rack.
2. If desired, screw the rails to the chassis for added support.
3. Repeat these steps for the left outer rail.
Warning: Do not pick up the server with the front handles. They are de-
signed to pull the system from a rack only.
Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the oor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.

2-6
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
Figure 2-3. Installing the Chassis into the Rack
Installing the Chassis into a Rack
Installing into a Rack
1. Conrm that the inner and outer rails are properly installed.
2. Line up the inner (chassis) rails with the front of the outer (rack) rails.
3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click" into position.
4. (Optional) Insert and tighten the thumbscrews that hold the front of the server
to the rack.
Note: Figure is for illustrative purposes only. Always install servers to the bottom
of a rack rst.

Chapter 3: System Interface
3-1
Chapter 3
System Interface
3-1 Overview
There are several LEDs on two control panels as well as others on the drive carriers
to keep you constantly informed of the overall status of the system as well as the
activity and health of specic components. A main power button is also located on
the right side (only) control panel.
3-2 Control Panel Button
Power
The single button located on the right control panel is the power on/off button.
Depressing this button will either power both nodes on or off.Turning off system
power with this button removes the main power but keeps standby power supplied
to the system.
3-3 Control Panel LEDs
The two control panels located on the front of the chassis have several LEDs. With
the exception of the power fail LED, these LEDs provide you with critical information
related to the node on the same side of the chassis. This section explains what each
LED indicates when illuminated and any corrective action you may need to take.
Power Fail
Indicates a power supply module has failed. The second power supply module will
take the load and keep the system running but the failed module will need to be
replaced. Refer to Chapter 6 for details on replacing the power supply. This LED
should be off when the system is operating normally.

Chapter 3: System Interface
3-2 3-3
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
1
2
Overheat/Fan Fail:
When this LED ashes, it indicates a fan failure. When on continuously it indicates
an overheat condition, which may be caused by cables obstructing the airow in
the system or the ambient room temperature being too warm. Check the routing of
the cables and make sure all fans are present and operating normally. You should
also check to make sure that the chassis covers are installed. Finally, verify that
the heatsinks are installed properly (see Chapter 5). This LED will remain ashing
or on as long as the indicated condition exists.
NIC1
Indicates network activity on the LAN1 port when ashing.
NIC2
Indicates network activity on the LAN2 port when ashing.
Heartbeat
On the 6038R-DE2CR16L, this is a serverboard heartbeat LED and indicates that
power is being supplied to the serverboard.
Power
Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.
3-4 Drive Carrier LEDs
Each drive carrier has two LEDs:
• Green: When illuminated, the green LED on the drive carrier indicates the drive
is powered on. If this LED is not lit, it means no power is being provided for the
drive. Please refer to Chapter 6 for instructions on replacing failed drives.
• Red: A steady red LED indicates a drive failure. If one of the drives fails, you
should be notied by your system management software. Please refer to Chapter
6 for instructions on replacing failed drives. If this LED ashes ~ once per second
(1 Hz) it indicates RAID rebuilding activity.

3-4
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
Notes

4-1
Chapter 4: Warning Statements for AC Systems
Chapter 4
Standardized Warning Statements for AC Systems
4-1 About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certied technicians should attempt to install or congure
components.
Read this appendix in its entirety before installing or conguring components in the
Supermicro chassis.
These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.
Warning!
This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
Warning Denition
警告の定義
この警告サインは危険を意 味します。
人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、
電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。
此警告符号代表危险。
您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。
此警告符號代表危險。
您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸
電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。

4-2
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
4-3
Warning Statements for AC Systems
Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie benden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.
GUARDE ESTAS INSTRUCCIONES.
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la n de chaque avertissement.
CONSERVEZ CES INFORMATIONS.
안전을 위한 주의사항
경고!
이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.
해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.
BEWAAR DEZE INSTRUCTIES
.   !




ןונקת תורהצהאהרהז
ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח
ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק
רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר
אורקל שי .ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא

4-4 4-5
Chapter 4: Warning Statements for AC Systems
SUPERSTORAGESYSTEM 6038R-DE2CR16L User's Manual
Installation Instructions
Warning!
Read the installation instructions before connecting the system to the power source.
Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.
¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.
Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.
Circuit Breaker
Warning!
This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.
設置手順書
システムを電源に接続する前に、設置手順書をお読み下さい。

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.
시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.
Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.
サーキット・ブレーカー
この製品は、短絡（過電流）保護装置がある建物での設置を前提としています。
保護装置の定格が250 V、20 Aを超えないことを確認下さい。
Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-
bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.
¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)
del edicio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.
Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit
dépend de l'installation électrique du local. Vériez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.
יכ
אדוול שי .ילמשח רצק תעינמל םינבמב תנקתומה הנגה לע ךמתסמ הז רצומ
60VDC, 20A-מ רתוי אל אוה ילמשחה רצקה ינפמ ןגמה רישכמה
يف
اه ت ي بثت مت يتلا ةري ص ق لا رئ اود لا ه م ت ي ام حلا ثاد ع م ىلع د م ت ع ي ج ت ن م لا اذ ه
ىنب م لا
20A, 250VDC :نم رثك أ سي ل يئاقولا زاهجلا ميي ق ت نأ نم د ك أت
警告
将此系统连接电源前,请先阅读安装说明。
警告
將系統與電源連接前，請先閱讀安裝說明。
警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。
警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。