Davinci gliders Tango xs User manual

DAVINCI GLIDERS / TANGO

REV. 3

01 MAY 2020

Davinci Products Inc.

53 Sinchon-gil, Okcheon-myeon, Yangpyeong-gun, Gyeonggi-do, South Korea. (12505)

Tel. +82(0)10-9799-3472 Fax. +82(0)10-9799-3472

[email protected] , [email protected]

DAVINCI GLIDERS / TANGO

Congratulations!

Thank you for choosing the TANGO

The TANGO has been designed for who are willing to progress in

the sport safely, chasing their rst XC ights but who are also com-

fortable with the technical control of this type of glider.

The TANGO is an easy and fun paraglider with excellent glide and a

very ecient speed system designed as a EN-C class glider.

This manual will help you to get all information about your

glider. We strongly recommend that you read this manual

carefully in order to be aware of any general limitations,

performance characteristics, take o and ight character-

istics, landing procedures, dealing with emergency situa-

tions and general maintenance.

This is information about the design of the TANGO, advice how to

use it best and how to care for it to ensure it has a long life,We hope

that the TANGO will give you a lot of satisfactory ying times.

WARNING!

THIS IS NOT TRAINING MANUAL. ATTEMPTING TO FLY THIS

OR ANY OTHER PARAGLIDER WITHOUT PROPER INSTRUC-

TION FROM A CERTIFIED PROFESSIONAL INSTRUCTOR IS

EXTREMELY DANGEROUS TO YOURSELF AND BYSTANDERS.

DAVINCI GLIDERS are carefully manufactured and inspect-

ed at the factory. Please use the glider only as described in

this manual.

Do not make any modications to the glider.

As with any sport – without taking the necessary safety pre-

cautions, paragliding can be dangerous.

Congratulations!

-DAVINCI GLIDERS TEAM-

DAVINCI GLIDERS / TANGO

INDEX

1. Technical DATA

2. Materials DATA

3. Introduction and

Pilot Target

14. Packing your TANGO

15. Maintenance and

cleaning

16. Caring tips

13. Landing

17. Warrantee

18. Respecting nature

and environment

4. Harness

6. Lines

7. Accelerator system

5. Risers

8. Pre-ight check

9. Take-0

9.1 Tow launch

11.2 Frontal collapse

10. In ight characteristics

11. Deations

11.1 Asymmetric collapse

11.5 Asymmetrical stall

11.6 B stall

11.4 Deep stall

11.3 Full stall

12.2 Spiral dive

12. Descent Techniques

12.1 Big ears

11.7 Cravat

DAVINCI GLIDERS / TANGO

1. Technical DATA

TANGO XS S M L

CELLS NUMBER 66 66 66 66

CLOSED 12 12 12 12

FLAT

AREA m² 21.0 22.9 24.8 26.8

SPAN m 11.5 12.0 12.5 13.0

ASPECT RATIO 6.3 6.3 6.3 6.3

PROJECTED

AREA m² 18.0 19.7 21.3 23.0

SPAN m 9.43 9.85 10.25 10.66

ASPECT RATIO 4.93 4.93 4.93 4.93

FLATTENING %14 14 14 14

CHORD

MAX m2.21 2.31 2.41 2.50

MIN m 0.50 0.52 0.55 0.57

AVER m 1.83 1.91 1.98 2.06

LINES HEIGHT m 7.11 7.42 7.73 8.03

MAIN 3/4/3

RISERS

NUMBER 3 A,A’/B/C

TRIMS NO NO NO NO

ACCELERATOR 165 165 165 165

WEIGHT RANGE MIN-MAX KG 60-85 70-95 85-105 95-120

CERTIFICATION EN-926-1/2

LTF EN-C EN-C EN-C EN-C

GLIDER WEIGHT KG 3.84.1 4.5 4.8

DAVINCI GLIDERS / TANGO

2. Materials DATA

CANOPY FABRIC CODE SUPPLIER

UPPER SURFACE 20D MF(WR)

E3W

DOMINICO TEXTILE CO

PORCHER IND

BOTTOM SURFACE E3H PORCHER IND

PROFILES 30D MF(NON WR) DOMINICO TEXTILE CO

RISERS FABRIC CODE SUPPLIER

MATERIAL 12mm zero stretch polyester GUTH&WOLF GMBH

PULLEYS Ronstan ball bearing Ronstan

SUSPENSION LINES FABRIC CODE SUPPLIER

UPPER CASCADES 8000U 70/50/30 EDELRID

MIDDLE CASCADES 8000U 130/90/70 EDELRID

MAIN 8000U 280/230/190 EDELRID

UPPER STABLE 9200-30 EDELRID

MAIN STABLE 8000U 130 EDELRID

UPPER BRAKE 8000U 50 EDELRID

MIDDLE BRAKE 8000U 90/70 EDELRID

MAIN BREAK A10N-200 EDELRID

DAVINCI GLIDERS / TANGO

3. Introduction and Pilot Target

The TANGO is an EN-C high performance glider. It has been designed for high skilled pilots for the ultimate

XC ight in comfort.

The TANGO is an easy and fun paraglider with excellent glide and a very ecient speed system designed

as a EN-C class glider. Long brake travel and excellent passive safety, as well as the good stability make the

good ideal for progression.

TANGO will be the most comfortable glider designed for the pilot who wants XC. The Smart nose system is

applied to TANGO.

Tango has special riser system and Smart Nose System designed by unique idea of Davinci Gliders. We hope

you will enjoy a safe and enjoyable ight with the high quality and durable fabrics and materials in optimal

designing technology.

-LTF and EN certication

The TANGO is certied during ocial testing as LTF /EN-C.

The glider has been type-tested for“one-seated” use only.

-For the TANGO it has minimum of 65cm symmetrical travel length at maximum total-load.

It would be dangerous to use the brake travel according to those numbers, because it is

not practicable to measure the brake travel during ight, and in turbulences the stall might

occur with less brake travel. If you want to use the whole brake travel of your glider safely, it

is necessary to do many intended spins and full stalls to get a feeling for the stall behaviour.

The TANGO does not have the trimmer system.

4. Harness

The TANGO is certied for harnesses in Group GH(without rigid cross-bracing). The suspensiion points of

the chosen harness should ideally have a caraviner distance of approximately 43cm and a height of 46cm

(TANGO XS 44cm).

DAVINCI GLIDERS / TANGO

6. Lines

7. Accelerator system

They come in dierent diameters of Kevlar and Dyneema lines. They must to be inspected every 100 hours

or 12months maximum.

In case of Brake lines, it was cut a little longer, so every pilot can adjust it according to his

personal taste.

But you must always leave 10cm before the brakes line starts acting in order to avoid trailing

edge deformation when the wing is fully accelerated. In case the brake handle comes loose

during ight or any brake lines is cut you can use the C riser softly for directional control instead

of brake line.

The accelerator has being limited in travel up to a safety point, however you can gain 15-20 km of extra

speed.

You have to adjust the harness to the speed system so you can use all the speed travel.

To do so you have to be seated in the ground meanwhile you are in your harness and adjust

the lines by pulling up the risers with tension. Another person help to do this is recommended.

Make sure also that the speed bar is not pulling down the risers when you are not using it.

Once all the gear is rigged you have to test the whole speed travel in calm air. The use of the

speed system reduces the angle of attack and the canopy may be more sensitive to collapses

therefore do not use near the ground or in turbulent air and in case you are hit by turbulence

remove your feet o the speed bar as quickly as possible. Always far away from the ground

when using the speed bar.

5. Risers

TANGO has 3 risers. The A riser has a red cover to easy iden-

tication. There is another line with red mailon. There is A3

and is for the big ears.

< The dierence not more than ±5 mm>

Standard

[mm]

Accelerated

[mm]

Travel length

[mm]

A470 305 165

A3 470 388 82

B470 360 110

C470 470 0

C3 470 415 55

A3 B1,2,3,STB

C1,2

Wood handle

A1,2

DAVINCI GLIDERS / TANGO

8. Pre-ight check

9. Take-0

To know yourself with the glider it is a good idea to perform practice inations and ground handling in

advance. You should have no diculties ying the TANGO for the rst time in suitable conditions, but as

with all new equipment.

When you have the new glider, the below points should be inspected.

- Check the lines are clear and not twisted.

- Connection points between the glider and harness.

- All harness buckles are closed.

- The Karabiners are fully closed and not damaged.

- The sewing, condition of the lines and connection of the lines are right

- Internal demage to ribs and diagonal ribs.

- Demage to the top and bottom panels and seams between panels.

TANGO has easy ination behaviour at the forward/reverse launch because of its prole system.

To get the right wing shape for the take-o, pull the brake until the canopy shows at the perfect

banana shape on the at ground. While inating the TANGO, you should hold both of th A risers

on your hands. Smoothly and gradually inate the wing. It does not need excessive energy and

you feel the lift force very fast. It does not tend to over-shooting characteristics and provides a

9.1 Tow launch

TheTANGO is easy to launch using a winch and it has no any special skills.To practice this

launching technique special training is needed and you have to know the procedures

and dangers, which are specic for winching. We do not recommend using any special

towing device which accelerates the glider during the winch launch.

DAVINCI GLIDERS / TANGO

11.2 Frontal collapse

TANGO does not come out the symmetrical front collapse by itself. It has high internal

pressure with its well designed prole. However a symmetric collapse my occur in

strong turbulent condition, but It could be fast recovered, if you apply the brake down

to 15 to 20cm. Release the brake lines, you may recover to the normal ight.

10. In ight characteristics

11. Deations

11.1 Asymmetric collapse

Asymmetric collapse usually happens when the pilot has not foreseen this

possible reaction of the wing.

Asymmetric collapses should be controlled by weight shifting away from

the collapse and applying enough brake to control your direction. And you

should use the brake to re-inate the glider.

TANGO has the best stable glide performance in a normal position with no any brakes. In strong thermals

and turbulence, we recommend to gently pull both brakes without acceleration to increase stability. The

brakes provide feedback about the surrounding air, which is needed for active ying.

To familiarize yourself with the TANGO your rst turns should be gradual and progressive. To make ecient

and coordinated turns with theTANGO rst look in the direction you want to go and check that the airspace

is clear. Your rst input for directional change should be weight-shift, followed by the smooth application of

the brake until the desired bank angle is achieved. To regulate the speed and radius of the turn, coordinate

your weight shift and use the outer brake.

In the unlikely event that a brake line releases from the brake handle or breaks, the glider is

manoeuvrable using the C-risers. By pulling gently on the C-risers it is possible to steer the

glider and land safely.

Alternative Steering:

In the unlikely event, that a brake line releases from the brake handle, or breaks, or the brake-

lines are tangled up, the glider is manoeuvrable using the rear-risers. By pulling gently on the

rear-risers, it is possible to steer the glider and land safely. Don’t pull the rear-risers too much,

to avoid a deep stall!

In spite of the TANGO has great stability of the ight, strong turbulence or piloting error may cause a portion

of the wing suddenly to be a deation.

DAVINCI GLIDERS / TANGO

11.5 Asymmetrical stall

11.6 B stall

It can take place when you pull one of the brakes too hard, or while spiraling

at a small speed in turbulence you increase the angle of attack. Rotation in the

asymmetrical stall is called negative spiral. This is one of the most dangerous

ying situations. In order to get out of asymmetrical stall, just release the

brakes. There may follow side thrust forward with a following wing collapse.

The TANGO has a very clean stable B stall. To enter the B stall, the pilot has to pull the

rst 20cm slowly until the r glider loses forward speed and starts to descend at around

6 m/s vertically. Do not release the brake handles during B stall. If you pull too much

B-line the glider may horseshoe and move around a lot. If this happens, release the B

risers.

To exit the B-stall the B-risers should be released symmetrically and in one

smooth, progressive motion. The glider will resume normal forward ight

without further input. Check you have forward ight again before using the

brakes.

11.4 Deep stall

11.3 Full stall

It is possible for gliders to enter a state of deep stall. This can be caused by

several situations including; a very slow release from a B-line stall; ying the

glider when wet; very old glider; or after a front/symmetric deation.

When you meet this situation you should fully raise up the both brakes and

push the A-risers forwards or use the speed bar symmetrically to regain

normal ight.

Full stall can occur when you fully pull the both brakes enough long time. This

means that the wing loses its forward momentum. To recover to the normal

ight you must release both brakes. After this usually comes a front dive

with a possible front deation. An asymmetric recovery (one control released

faster than the other) from a full-stall can cause a big dynamic collapse. The

full-stall is a hazardous manoeuvre and as such outside the scope of this

manual. You should practice and learn this manoeuvre only on a SIV course

under professional instructor.

DAVINCI GLIDERS / TANGO

12.2 Spiral dive

The spiral dive is the most demanding descent technique and should be

learned at enough height, preferably during an SIV course.

When you hold one sided brake down for a long time, the glider goes into a fast sharp

turn and loses a lot of height. The sink rate could be more than 15 m/sec. To get out of

the spiral dive you must release the inner brake and use the outside brake to manage

your sink rate. Mind that TANGO may take one more turn after releasing the brake.

12. Descent Techniques

12.1 Big ears

Sink rate can be decreased in a controlled way by folding both wing tips. While

holding the brakes you should symmetrically pull the outermost A-risers.

In order to return to the normal ight, you should release the A-risers and

pull the brake short times until wing tips regain pressure.

Spiraling is not permitted with big ears, because of the increased load on the

remaining lines so that they can be physically deformed.

11.7 Cravat

In case a cravat should occur from an asymmetric collapse or other

manoeuvres, it is important to keep your ying direction by applying some

brake on the opposite side and weight shift.

You can also use strong deep pumps on the brake to the cravated side. If

a pull of the break line is unsuccessful, pulling the stable line which is the

outermost line on the B-riser may work.

If you can not do it and the rotation is increasing, you must use the parachute.

DAVINCI GLIDERS / TANGO

14. Packing your TANGO

15. Maintenance and cleaning

Spread the TANGO completely out on the ground. Separate the lines to the each side. The TANGO must be

folded cell to cell to keep the plastic reinforcement at the leading edge lie at on each other and don’t get

bent. Try to pack your TANGO as loosely as the rucksack allows, because every fold weakens the fabric.

Avoid packing the glider where it is wet or abrasive conditions(sand, asphalt pavement,

concrete)

Cleaning should be carried out with only pure water. If the glider comes in contact with salt

water, clean thoroughly with fresh water. Do not use solvents of any kind, as this may remove

the protective coatings and destroy the fabric.

13. Landing

We recommend to land with trimmers to the normal slow position. Don’t use the sharp turns

or radical maneuvers.

When you are 1-2m over the ground, you should face into wind and standing upright and ready

to run. Finally you may pull the brakes smoothly for minimize vertical speed.

Don’t hit the ground by your overtake the glider. If you in windy condition, as soon as you touch

the ground you have to turn around to face the glider and move towards it during full pulling

break symmetrically.

DAVINCI GLIDERS / TANGO

17. Warrantee

18. Respecting nature and environment

The producer guarantees the correctness of the declared characteristics and the paraglider’s

normal performance for One year after the purchase date. The producer conducts special, and

after warranty repairs and maintenance at the owners’request for an extra price.

We recommend to inspect your paraglider (including checking suspension line strength, line

geometry, riser geometry and permeability of the canopy material) one time at one years, or

every 100 hours of ying time (whichever comes rst); Those inspection must be made by

manufacturer, importer, distributor, dealer or other authorised persons. The checking must be

proven by a stamp on the certication sticker on the glider as well in the manual book.

Finally, we would ask each pilot to take care of nature and our environment. Respect nature and

the environment at all times but most particularly at take-o and landing places. Respect others

and paraglider in harmony with nature.

Do not leave marked tracks and do not leave rubbish behind. Do not make unnecessary noise

and respect sensitive biological areas.

The materials used on a paraglider should be recycled. Please send old Davinci gliders back to us

Davinci Gliders oce. We will undertake to recycle the glider.

16. Caring tips

- Do not expose your glider to the sun any longer than necessary

- Keep it away from water and other liquids

- Do not let the front edge hit the ground

- Keep your glider away from re

- Do not put anything heavy on your glider, do not pack it in a rucksack too tightly.

- Regularly inspect the canopy, lines, risers and harness. If you nd any defects,

contact your dealer or the manufacturer. Do not attempt to repair the paraglider by yourselves.

- If you detect a damaged line, inform the dealer or manufacturer about the line number

according to the line plan

- Keep your TANGO in a bag in a dry well-ventilated place under neutral temperature and

humidity conditions

- If you do not use the glider, then once a month you should unpack it, ventilate it well,

and then pack it back in the bag

DAVINCI GLIDERS / TANGO

A B C D Brake

17037 7000 7078 7157 7342

27011 6974 7050 7131 7111

36980 6942 7017 7096 6965

46986 6948 7023 7100 6891

56930 6893 6964 7037 6806

66906 6869 6938 7011 6672

76867 6831 6894 6961 6684

86869 6834 6893 6957 6783

96839 6809 6873 6670

10 6781 6758 6821 6683

11 6679 6667 6721 6709

12 6670 6660 6710 6864

13 6607 6606 6648

14 6610 6609 6646

15(stable) 6430 6440 6521

16(stable) 6406 6433 6509

XSmall size

Checked line sheet(with riser)

The measured values at the lower surface of the tailing edge, cll depth and

spacing of the articulation points were determined under tensile load of 50N.

The length dierence is not more than ±10 mm.

DAVINCI GLIDERS / TANGO

A B C D Brake

17343 7305 7386 7469 7657

27317 7279 7358 7442 7417

37286 7247 7324 7406 7265

47292 7253 7331 7411 7190

57234 7196 7271 7348 7102

67209 7172 7245 7320 6963

77170 7133 7200 7269 6976

87172 7136 7199 7266 7078

97139 7110 7178 6963

10 7079 7056 7123 6977

11 6971 6961 7018 7005

12 6962 6954 7007 7165

13 6899 6898 6942

14 6901 6901 6939

15(stable) 6714 6724 6808

16(stable) 6689 6717 6796

Small size

DAVINCI GLIDERS / TANGO

Large size

Medium size A B C D Brake

1 7618 7580 7660 7741 7949

2 7592 7552 7631 7713 7702

3 7560 7520 7597 7677 7546

4 7567 7527 7604 7682 7470

5 7508 7468 7543 7617 7359

6 7482 7443 7515 7589 7215

7 7441 7403 7468 7535 7228

8 7444 7406 7468 7532 7335

9 7410 7380 7451 7216

10 7348 7324 7394 7230

11 7237 7225 7285 7259

12 7227 7218 7273 7438

13 7160 7159 7205

14 7162 7161 7202

15(stable) 6966 6977 7065

16(stable) 6940 6969 7052

A B C D Brake

1 7921 7881 7965 8049 8304

2 7893 7853 7935 8021 8049

3 7861 7820 7901 7984 7888

4 7869 7828 7909 7990 7812

5 7808 7768 7846 7923 7707

6 7781 7742 7817 7894 7558

7 7739 7700 7769 7838 7573

8 7741 7703 7768 7835 7683

9 7707 7676 7751 7560

10 7643 7618 7692 7574

11 7527 7516 7579 7604

12 7517 7508 7566 7779

13 7447 7447 7496

14 7449 7449 7492

15(stable) 7255 7257 7348

16(stable) 7218 7248 7335

DAVINCI GLIDERS / TANGO

Line plan

DAVINCI GLIDERS / TANGO

Serial Number

Date of Production

Dealer

Date of sales

Check and repair information

AIR TURQUOISE SA | Rte du Pré-au-Comte 8 | CH-1844 Villeneuve | +41 (0)21 965 65 65

Test laboratory for paragliders, paraglider harnesses and paraglider reserve parachutes

Line and Riser Measurements of flight test Paraglider (1)

Report No. : Sample name: Date measure: Place:

Manufacturer: S/N: Responsible: Linked:

Total line length including risers [mm] Main brake line with diff color than A,B,C main line? Yes

+strap

Manu (2) Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Sample

Center 17037 7041 47000 6995 -5 7078 7074 -4 7157 7146 -11 6430 6427 -3 7342 7347 5

27011 7014 36974 6969 -5 7050 7045 -5 7131 7119 -12 6406 6405 -1 7111 7115 4

36980 6984 46942 6936 -6 7017 7010 -7 7096 7087 -10 6440 6438 -2 6965 6970 5

46986 6992 66948 6946 -2 7023 7019 -4 7100 7089 -11 6433 6433 06891 6896 5

56930 6934 46893 6894 16964 6963 -1 7037 7029 -8 6521 6519 -2 6806 6805 -1

66906 6911 56869 6869 06938 6936 -2 7011 7004 -8 6509 6506 -3 6672 6674 2

76867 6872 56831 6832 16894 6892 -2 6961 6953 -8 6684 6684 0

86869 6872 36834 6833 -1 6893 6890 -3 6957 6946 -11 6783 6784 1

96839 6832 -7 6809 6801 -8 6873 6864 -9 6670 6670 0

10 6781 6778 -4 6758 6751 -7 6821 6816 -5 6683 6682 -1

11 6679 6675 -4 6667 6661 -6 6721 6716 -5 Stab line to riser: 6709 6711 2

12 6670 6664 -6 6660 6654 -6 6710 6705 -5 B6864 6865 1

13 6607 6599 -8 6606 6600 -6 6648 6643 -5

Wing 14 6610 6604 -6 6609 6602 -7 6646 6639 -7

tip 15 Number Cell: 64

16 Weight of the glider [kg]: 3.84

18 Tolerance [mm]

(4)

:±15

Riser measurement - total length (inner edge) [mm] (3) Acc system configuration max travel Test Atmosphere AGL

Risers Std Acc Trim Risers Std Acc No. of risers 3 Pressure [hPa] 971.6

A499 333 n/a A471 305 Tolerance [mm] 5 Humidity [%] 30

A' 497 359 n/a A' 469 331 Temperature [°C] 22.4

B497 386 n/a B469 358 Carabiner [mm] 28

C' 496 439 n/a C' 468 411 Tolerance [mm] 2

C' 499 498 n/a C' 471 470 Plausibility check :

Acc 166 *[mm] Acc 166 *[mm] *Travel range (distance [mm] 500 500

Trimmer n/a [mm] Trimmer n/a [mm] between A and rear riser) Another trim configuration No [mm] 10000 10003

If yes (description): Remark:

Instrument validity date

Laser distance meter 07.09.2023 Uncertainty of instrument [mm] 3

Line measurements system 07.09.2023

Villeneuve

ISO 91.20

A B C D E Stab Brake

PG_1676.2020

Davinci Product Tango XS

KTF-XS11230-GRBL 22.04.2020

Claude Thurnheer

(3) Risers, Std=Trim speed, Acc=Accelerated, AND if trimmer: Open=trimmer open, Closed=trimmer closed, Trim=measured at this position. (4)Tolerance line and riser is +/-15 [mm]

Total

length

(incl.

Carabiner

connect)

Total

length

(no cara-

biner or

con-

nect)

Present inspection’s scope only extends to the conformity of a given sample, on a given date and in a given place – as mentioned here above. The validation of this report is given by the signature of the test manager on inspection certificate 71.8.1

(1)Total length measured from the underside of the glider to the inner edge of the risers with a tenstion of 50 [N]. Measured values do not include the uncertainty/The uncertainty stated is the expanded uncertainty obtained by multiplying the standard uncertainty

by the coverage factor k = 2. The measured values lies within the assigned range of values with a probability of 95%. (2) Manu=Values from manufacturer, Sample=Measured by inspector.

RE | rev 17 | 11.10.2019 Page 1 | 1 ISO | 91.24

AIR TURQUOISE SA | Rte du Pré-au-Comte 8 | CH-1844 Villeneuve | +41 (0)21 965 65 65

Test laboratory for paragliders, paraglider harnesses and paraglider reserve parachutes

Line and Riser Measurements of flight test Paraglider (1)

Report No. : Sample name: Date measure: Place:

Manufacturer: S/N: Responsible: Linked:

Total line length including risers [mm] Main brake line with diff color than A,B,C main line? Yes

+strap

Manu (2) Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Sample

Center 17343 7341 -2 7305 7301 -4 7386 7383 -3 7469 7459 -10 6714 6714 07657 7664 7

27317 7317 -1 7279 7276 -3 7358 7354 -4 7442 7431 -11 6689 6690 17417 7428 11

37286 7287 17247 7248 17324 7321 -3 7406 7397 -9 6724 6724 07265 7274 9

47292 7297 57253 7254 17331 7326 -5 7411 7400 -11 6717 6715 -2 7190 7198 8

57234 7238 47196 7199 37271 7269 -2 7348 7340 -8 6808 6806 -2 7102 7107 5

67209 7215 67172 7171 -1 7245 7244 -1 7320 7311 -9 6796 6796 06963 6978 15

77170 7174 47133 7133 07200 7198 -2 7269 7259 -10 6976 6983 7

87172 7177 57136 7137 17199 7196 -3 7266 7255 -11 7078 7083 5

97139 7130 -9 7110 7101 -9 7178 7171 -7 6963 6966 3

10 7079 7073 -6 7056 7049 -7 7123 7118 -5 6977 6981 4

11 6971 6965 -6 6961 6955 -6 7018 7012 -6 Stab line to riser: 7005 7008 3

12 6962 6955 -7 6954 6947 -7 7007 7001 -6 B7165 7170 5

13 6899 6892 -7 6898 6892 -6 6942 6939 -3

Wing 14 6901 6895 -6 6901 6893 -8 6939 6932 -7

tip 15 Number Cell: 64

16 Weight of the glider [kg]: 4.14

18 Tolerance [mm]

(4)

:±15

Riser measurement - total length (inner edge) [mm] (3) Acc system configuration max travel Test Atmosphere AGL

Risers Std Acc Trim Risers Std Acc No. of risers 3 Pressure [hPa] 971.4

A497 331 n/a A469 303 Tolerance [mm] 5 Humidity [%] 30

A' 497 357 n/a A' 469 329 Temperature [°C] 22.8

B498 386 n/a B470 358 Carabiner [mm] 28

C' 497 440 n/a C469 412 Tolerance [mm] 2

C500 500 n/a D472 472 Plausibility check :

Acc 166 *[mm] Acc 166 *[mm] *Travel range (distance [mm] 500 500

Trimmer n/a [mm] Trimmer n/a [mm] between A and rear riser) Another trim configuration No [mm] 10000 10003

If yes (description): Remark:

Instrument validity date

Laser distance meter 07.09.2023 Uncertainty of instrument [mm] 3

Line measurements system 07.09.2023

(3) Risers, Std=Trim speed, Acc=Accelerated, AND if trimmer: Open=trimmer open, Closed=trimmer closed, Trim=measured at this position. (4)Tolerance line and riser is +/-15 [mm]

Total

length

(incl.

Carabiner

connect)

Total

length

(no cara-

biner or

con-

nect)

by the coverage factor k = 2. The measured values lies within the assigned range of values with a probability of 95%. (2) Manu=Values from manufacturer, Sample=Measured by inspector.

Villeneuve

ISO 91.20

A B C D E Stab Brake

PG_1677.2020

Davinci Product Tango S

KTG-S11240-BRW 22.04.2020

Claude Thurnheer

RE | rev 17 | 11.10.2019 Page 1 | 1 ISO | 91.24

AIR TURQUOISE SA | Rte du Pré-au-Comte 8 | CH-1844 Villeneuve | +41 (0)21 965 65 65

Test laboratory for paragliders, paraglider harnesses and paraglider reserve parachutes

Line and Riser Measurements of flight test Paraglider (1)

Report No. : Sample name: Date measure: Place:

Manufacturer: S/N: Responsible: Linked:

Total line length including risers [mm] Main brake line with diff color than A,B,C main line? Yes

+strap

Manu (2) Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Manu Sample Diff Sample

Center 17618 7613 -5 7580 7573 -8 7660 7654 -6 7741 7734 -7 6976 6962 -14 7969 7947 -23

27592 7587 -5 7552 7544 -8 7631 7627 -4 7713 7710 -4 6950 6936 -14 7722 7703 -19

37560 7558 -2 7520 7511 -9 7597 7593 -4 7677 7671 -6 6987 6967 -20 7566 7546 -20

47567 7567 07527 7520 -7 7604 7599 -5 7682 7678 -4 6979 6958 -21 7490 7467 -23

57508 7507 -1 7468 7465 -3 7543 7541 -2 7617 7615 -2 7075 7056 -19 6159 7366 1207

67482 7483 17443 7438 -5 7515 7512 -3 7589 7590 17062 7041 -21 7215 7224 9

77441 7442 17403 7398 -5 7468 7464 -4 7535 7532 -3 7228 7235 7

87444 7445 17406 7403 -3 7468 7466 -2 7532 7530 -2 7335 7344 9

97410 7398 -12 7380 7367 -14 7451 7437 -14 7216 7220 4

10 7348 7335 -13 7324 7312 -12 7394 7380 -14 7230 7230 0

11 7237 7224 -13 7225 7212 -14 7285 7272 -13 Stab line to riser: 7259 7260 1

12 7227 7216 -11 7218 7206 -12 7273 7260 -14 B 7438 7425 -13

13 7160 7158 -2 7159 7155 -4 7205 7207 2

Wing 14 7162 7160 -2 7161 7159 -2 7202 7202 0

tip 15 Number Cell: 64

16 Weight of the glider [kg]: 4.56

18 Tolerance [mm]

(4)

:±15

Riser measurement - total length (inner edge) [mm] (3) Acc system configuration max travel Test Atmosphere AGL

Risers Std Acc Trim Risers Std Acc No. of risers 3 Pressure [hPa] 973.9

A496 329 n/a A468 301 Tolerance [mm] 5 Humidity [%] 34

A' 495 354 n/a A' 467 326 Temperature [°C] 21.4

B495 383 n/a B467 355 Carabiner [mm] 28

B' 495 437 n/a B' 467 409 Tolerance [mm] 2

C495 495 n/a C467 467 Plausibility check :

Acc 167 *[mm] Acc 167 *[mm] *Travel range (distance [mm] 500 500

Trimmer n/a [mm] Trimmer n/a [mm] between A and rear riser) Another trim configuration No [mm] 10000 10003

If yes (description): Remark:

Instrument validity date

Laser distance meter 07.09.2023 Uncertainty of instrument [mm] 3

Line measurements system 07.09.2023

Villeneuve

ISO 91.20

A B C D E Stab Brake

PG_1623.2020

Davinci Tango M

KTG-M11050-BRW 10.02.2020

Claude Thurnheer

(3) Risers, Std=Trim speed, Acc=Accelerated, AND if trimmer: Open=trimmer open, Closed=trimmer closed, Trim=measured at this position. (4)Tolerance line and riser is +/-15 [mm]

Total

length

(incl.

Carabiner

connect)

Total

length

(no cara-

biner or

con-

nect)

by the coverage factor k = 2. The measured values lies within the assigned range of values with a probability of 95%. (2) Manu=Values from manufacturer, Sample=Measured by inspector.