DCG GH05 User manual

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
16
FOR YOUR SAFETY PLEASE READ THIS MANUAL CAREFULLY
AND OPERATE THE APPLIANCE ACCORDING TO THE TO THESE
INSTRUCTIONS. PLACE INSTRUCTIONS IN A SAFE PLACE FOR
FUTURE REFERENCE. ONLY USE IN A WELL VENTILATED AREA
THIS PRODUCT IS NOT SUITABLE FOR PRIMARY HEATING
PURPOSES
WARNING:IFTHEINFORMATIONINTHISMANUALISNOTFOLLOWED
EXACTLY. A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY
DAMAGE. PERSONAL INJURY OR LOSS OF LIFEWARNING: IF THE
INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY. A
FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE.
PERSONAL INJURY OR LOSS OF LIFE
TECHNICAL CHARACTERISTICS
Type:
Infrared Space Heater, mobile, equipped with
Atmosphere sensing system and fame ailure
Device.
Dimensions: 40 x 40 x 72 ( D x W x H )
Category: I 3+(28-20/37)
COUNTRIES OF DESTINATION: CH, ES, GR, RO, SK, IT and PT
Pressure: Butane at 28-30mbar and Propane at 37mbar
Heater input: Minimum : 1.50kW,
Medium : 2.9kW
Maximum: 4.20kW
Consumption: Minimum: 110g/h,
Medium: 207g/h
Maximun: 305g/h
Regulator outlet pressure:30mbar
POWER: 220-230V/50-60HZ
Electric input: 1.5kW

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
17
Injector size: 0.60mm
Ignition system:Piezo Electric
Cylinder Type:
UP to 15kg cylinders (at maximum 32 cm (dia.) x 620 cm (H)
Weight (kg) 9.5 kg
Weight (kg) 9.5 kg
SAFETY PRECAUTIONS
1. Always use Heater in
accordance with instructions
supplied with each heater.
Keep instructions in a safe place.
3.DO NOT position heater close
furniture.
4.DO NOT move heater from
room to room when lit.
2. DO NOT place clothes or
other material on the heater.
This could cause a re risk/
or aect the eciency othe
appliance.

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
18
5. DO NOT position heater close
to walls, furniture, net curtains,
bed linen or any fammable
materials as this could result
in a risk o re. The ollowing
minimum distances should
be respected: 50 cm from the
sides and 100cm from the front.
ALWAYS face the heater towards
the centre of the room. The
heater should be positioned on a
level surface at all times.
6. If a leak is suspected. DO
NOT disconnect the regulator.
Turn off the gas supply at the
gas bottle or gas regulator.
Take the appliance outdoors in
a fame ree atmosphere.Turn
on the gas supply and Check all
the connections.Slowly brush the
connections with soapy water,or
a leak detection spray a gas
leak will form bubbles.If a leak is
found turn the gas off.DO NOT
use the heater again until it has
been checked by a competent
person in accordance with the
Gas Safety(installations and use)
Regulations 1998

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
19
Note: Minimum distance from mobile heater to the ceiling at least
1000mm.
USING ENVIRONMENT
Your heater consumes oxygen while it is in use. For this reason,
adequate ventilation should be provided in rooms in which the
heater is used. This ensures the removal of products of combustion
and allows the entry of replacement air.
Adequate ventilation should considerably reduce condensation
occurring. The following table shows the smallest sizes of room
suitable for each heat setting and the ventilation, which should be
provided.

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
20
FOR INFRARED MODELS:
1. This appliance requires a hose and a regulator.
2. Only use in well ventilated areas.
3. Do not use in vehicles, caravans or auto caravans.
4.
Do not attempt to use in high rise fats, basements, bathroom or bedrooms.
5. This appliance should be tested for leaks before initial use and
whenever the cylinder is re-connected.
6. It is important that all gas connections have been correctly made
to prevent any leakage. Do not use a naked fame to test or leaks.
Use soapy water or a leak detection spray.
7. Always use your cylinder in an upright position.
8. Always turn off the appliance at the regulator when not in use.
9. When lighting your heater or the rst time or ater a period o
time has passed since the last use, light the heater outside and
burn outdoors for 15 minutes.
10.Do not use your heater while sleeping.
11.Do not use your heater in high-rise fats.
12.Do not use your heater in basements ,bathrooms or bedrooms.
13.This appliance requires a hose and a regulator, check with your
gas supplier for the correct type according to the cylinder being
used and any regulations at that time.
14.The guard on the appliance is to prevent risk o re or injury rom
burns and no part of it should be permanently removed. It does
not give ull protection or young children or the inrm. We would
recommend a reguard to BS 8423 be tted.
Number of Radiant
Continuously IN USE
1
2
3
OTHER ROOM SIZE
15cubic meters-
say 1.5m*4m*2.5m
28cubic meters-
say 2.8m*4m*2.5m
42cubic meters-
say 4.2m*4m*2.5m
LIVING ROOM SIZE
28 cubic meters-
say 2.8m*4m*2.5m
58 cubic meters-
say 5.2m*4m*2.5m
84 cubic meters-
say 8.4m*4m*2.5m
VENTILATION
Low level High level
105cm2 105cm2
105cm2 105cm2
105cm2 105cm2

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
21
Use only regulator and hose approved for LP Gas at the correct
pressures.
The pressure adjuster should comply with the standard EN12864 and
current regulations in the country where it is installed,which may be
found at your nearest retailer of gas items,Refer to the technical date.
It is strictly prohibited to use adjustable pressure.
The life expectancy of the regulator is estimated as 10 years.It is
recommended that the regulator is changed within 10 year of the
date of manufacture or the national conditions require it.
The type of replaceable hose should meet the standard of EN1763-1
Class 3.
The hose used must conform to the relevant standard for the country
of use.The length of the hose must be 0.5m (maximum).Worn
or damaged hose must be replaced.Ensure that the hose is not
obstructed,kinked,or in contact with any part of the appliance other
than at its connection.It is recommended that the hose is changed
within 1 year of the date of manufacture or the national conditions
require it.
How to choose proper regulator:
37 mbar regulator with butane,propane or their mixtures @ category
I3B/P(37)
30 mbar regulator with butane,propane or their mixtures @ category
I3B/P(30)
Warning
Perform a leak test on all connections every time you reconnect the
cylinder, or ithe heater has not used or a signicant period.
Don’t twist the fexible tube or the hose.
Don’t move the appliance when lit

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
22
FAULT FINDLING CHART:
REPAIRS TO BE CONDUCTED BY AUTHORSED
SYMPTOMS
1.Pilot will not light
automatically No spark across electrode gap
(a)Ensure that piezo-electric
switch is functioning correctly.
(b)Check that electrical lead is
not damaged.
2.Pilot will not light automatically
but points(a) to (e) are satisfactory
and the pilot will light with a match
Incorrect position of spark in
relation to pilot gas fow. Re-position spark plug so that spark jumps across gas fow.
3.Heater will not remain
alight when pressure is
released from ignition button
Electro-magnetic valve
closes while heater is alight.
(a)Ensure that thermocouple
probe is located in pilot fame.
(b)Ensure good connection
between thermocouple and valve.
(c)Check thermocouple.
(d)Check electromagnetic valve.
4.After changing to maximum
position with all three plaques
alight one or more plaques
appear below normal intensively
(a)Blocked jets.
(b)Partially blocked supply tube. (a)Remove and clean blocked jet. (b)Remove supply tube, remove
jets and blow through the tube.
5.Diculty in cross lighting
from position 1 to position
2 or 3
(a)Air draught directed away
rom rst plaque.
(b)Position othe pilot fame.
(a)Change the location of
the appliance so that it is not
adversely affected by air draught.
(b)Position pilot so that impinges
across bottom corner of 2nd
plaque as well as 1st plaque.
6.Smell of combustion Missing piece of ceramic
reclay.
Inspect perimeter of each plaque
and locate place where some
reclay has been displaced.
Repair with PYRUMA and leave to
sot for approx.24 hours.
FAULT REMEDY

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
23
CONSTRUCTION AND FUNCTION
CONNECTING THE CYLINDER
1.Place the gas lled cylinder into the back othe heater.
2.Clip on the gas regulator to the gas cylinder,connect the regulator
to fexible tubing and the valve.
3.Turn the cylinder and the regulator on.
4.Where the regulator is not supplied or is missing please contact
your gas dealer to advise of the correct type for the gas cylinder
being used.
5.IMPORTANT TEST FOR LEAKS:
Thismustbecarriedoutinawellventilated area,ree romnakedfames
• 1.Piezoelectric ignitor
• 2.Gas control knob
• 3.Switch for fan heater
• 4.Thermostat of fan heater
• 5.Fan heater
• 6.Grid
• 7.Burner group
• 8.Pilot system
• 9.Rear cover

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
24
and any other sources of ignition.With the regulator connected to
the cylinder turn on the regulator control. Brush all hose connections,
pipe connections to the valve and gas cylinder with a 50;50 solution
of detergent and water or a leak detection spray. A stream of bubbles
forming indicates a leak.If a leak is found turn off at the regulator and
disconnect the regulator from the bottle and remove the gas cylinder
outdoors or to a well ventilated area. Contact your gas supplier for
assistance. DO NOT USE THE HEATER..
Fix the rear cover after leakage test.
HOW TO CHANGE A CYLINDER
1.Turn off at the regulator and allow the heater to cool fully before
removing and replacing the cylinder. Do not attempt to replace
the cylinder whilst the heater is still in use.
2.Cylinders must be replaced in a fame ree environment.
3.Do not smoke while changing the cylinder
4.When you need to replace your empty cylinder, turn the gas off
at the valve or regulator and take the empty cylinder out of the
heater.
5.Remove the regulator from the empty cylinder.
6.Follow the steps described under “Connecting the Cylinder”,
connect a new cylinder.
FUNCTION INTRODUCE:
1.Gas and Electric Function
This product’s design keeps warm from gas burnr and electric used.
2.Multiple protection function
*Oxygen Depletion protection function (ODS): This product equip
with ODS, once appearing the circumstance of oxygen shortage, this
ODS device will cut off the Gas Supply for protection.
*Over-Heat protection function: This electric heater equip
with Thermostat, if the product is not used correctly to make the

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
25
temperature risen high, The heating element will stop working
remaining the motor fan.You should take out the power cord until the
temperature is down to normal, then you could connect the power
code to turn on it, the Heating element will recover a normal work.
*Non-self-resetting thermal cut-out protection function: This
product equip with Non-self-resetting thermal cut-out device. Once
appearing accident, like short circuit, the function will permanently
cut off the power, preventing from the occurrence of trouble.
*Regulating the thermostat for fan heater: You could regulate the
room temperature by the thermostat.The thermostat is designed to
control the room temperature rougly from 0-32 degree.
*Anti-dumping function for fan heater: When the heater fall down
during the fan heater working,the anti-tilt switch will be activated to
turn off the heating element.
3. Used in Cold breeze or Hot Breeze two function
The breeze machine of this product can choose to blow cold breeze
or blow hot breeze.

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
26
OPERATION GUIDE
LIGHTING INSTRUCTION
The heater is designed to be used gas and electric together.
a.The gas heater has three settings. Lighting and Minimum(Pos.1);
Medium (Pos.2) and Maximum(Pos.3).
b.The electric heater has two function:cold breeze and heating element.
1.GAS KNOB CONTROL
LIGHTING:
Turn on the gas by turning the gas regulator to the on position.
The heater can be regulated to three different heat intensities
Pos.1,Pos.2,Pos.3.
• Press down and turn the control knob to and hold for 10
seconds.
• Whilst still pressing down the control knob press the ignition button
until the pilot light (at the bottom of the burner) ignites. Continue

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
27
to hold the control knob down for 10-15 seconds more. Release
the button ithe pilot fame goes out repeat the above operation
HEAT SETTINGS
To change from minimum to maximum gently press control button
and turn it position 3.
To change from maximum to medium gently press control button
and turn it position 2.
Turn off heater at cylinder or turn the switch on the regulator to the
“OFF” position. If the heater is not be used for a period of time
disconnect the regulator from the cylinder and replace any value
protection plug or cover
Attention!
Please do not forcefully turn the control knob, the button should be
pushed down before changing the heat control settings. The control
button will not turn without pushing downwards. Ensure the button
is locked into the heat setting /position required.
2.HEATING FAN OPERATION:
Importan:The fan heater could start to work after the thermostat turn
on.
1) Control knob of thermostat
To use the fan heater,you should regulate the temperature by the
thermostat rst.Turn the thermostat knob clockwise,once you hear
a “Click”,that means the thermostat start to work.You could set up
the temperature from 0-32 degree roughly,then to turn on the fan
heater.To turn off the fan heater,you could turn the thermostat knob
anti-clocksise until you hear a “Click” or by the button of the fan
heater.

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
28
2) The electric combination switches operation method
a. Breeze machine switch
Press on the button for turbo fan only,the turbo fan will work and can
blow cold breeze.
b. Heating element switch
Turn on the turbo an rst, then press on the button or heating
element. The heating element will begin to work,at the same time,
the turbo fan blows hot breeze. If the the turbo fan does not work,
heating element can not work.There are two buttons for heating
element,press one button is 750 Watts. Two buttons be connected,
the power is totally 1500 Watts.
Atention:
The fan heater is with overheating protection.If the fan heater is too
hot,the heating element will not work.You should disconnect the
power code to wait for some minutes until the heater is cold,then it
could be restarted again.
WARNING
1. Never attempt to light if the hose appears loose or damaged in
any way.
2. Do not press the ignition button for more than 40 seconds.
3. Never disconnect the regulator while cylinder valve or regulator
is open.
4. Don’t change cylinders with in area in which open re exists.
5. Don’t expose your cylinder to extreme heat.
6. Do not store any other cylinders in the room in which your heater
is being used.
7. Do not insert your nger or any other material through the ront
panel of the heater.
8. Leave at lease 1 meter distance between your heater and any
other heat source.
9. Do not let unauthorized persons tamper with your heater.

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
29
10. Do not use appliance under electrical socket outlets.
11. Do not use the heater in bathrooms, showers of swimming pool,
leisure vehicles such as caravans or auto caravans.
12. This heater must not be used without a gas cylinder tted or
stability purposes.
13. Do not cover your heater. Fabrics, clothing, hangings, net
curtains, bed lines and other fammable materials may ignite i
placed against the outlets of your heater.
14. In the event of leakage, the appliance should be turned off either
at the gas container valve or at the regulator switch-on valve and
the regulator disconnected from the cylinder.
15. After use, turn off the appliance at the regulator switch on valve
and the regulator disconnected from the cylinder.Turn off the
appliance from the container by means of the LPG container
isolating valve.
16. Only use in a well ventilated areas
17. The guard on this appliance is to prevent risk o re or injury
from burner and no part of it should be permanently removed.
IT DOES NOT GIVE PROTECTION FOR YOUNG CHILDREN OR
THE INFIRM.
18. Do not move the appliance when operating,shocks and bumps
may activate the safety device.
19. Do not use this heater with a programmer,timer,separate remote-
control system or any other device that switches the heater on
automatically,since a re risk exists ithe heater is covered or
positioned incorrectly.
20. The reguard othis heater is intended to prevent direct access
to heating elements and must be in place when the heater is i
us.The reguard does not give ull protection or young children
and or inrm persons.

Instruction Manual GH05 GAS HEATER WITH TURBO
dcg16.it
30
STORAGE
1. Disconnect the cylinder and remove from the appliance.
2. Store cylinders in a well-ventilated area away from combustible
material. Storage should preferably be outdoors. Cylinders must
not be stored be in a basements or in high-rise fats.
3. The heater should be covered in a dry, dust-free area in its original
packaging.
CLEANING
1. Use a damp soapy wrung out cloth to clean the exterior and
cylinder storage area of your heater.
2. Make sure that no water gets onto the burners or pilot/light area.
Wipe the heater completely dry before use.
3. Don’t use abrasive cleaners as they may damage the quality of
paint nish.
MAINTENANCE
1. Check fexible tubing between regulator and heater regularly and
replace If perished, worn or damaged,
2. It is recommended that the heater be serviced every year by a
competent person in accordance with the Gas Safety (installations
and use) Regulations 1998.
3. If any parts need replacing, they should be replaced only with the
correct parts as supplied by the original manufacturer.
4. If no use after a long time term,user should check it if mobile
heater does work normally,or example,fexible tubing and
regulator are till in valid time,the gas connection from cylinder to
heater is without any leakage,the heater can be ignited without
light-back,without big noise inside heater.

Manuale d’istruzioni GH05 STUFA A GAS CON TURBO
dcg16.it
31
INFORMAZIONI AGLI UTENTI
ai sensi del Decreto Legislativo N° 49 del 14 Marzo 2014
“Attuazione della Direttiva 2012/19/UE sui riuti di apparecchiature
elettriche ed elettroniche (RAEE)”
Il simbolo del cassonetto barrato riportato sull’apparecchiatura indi-
ca che il prodotto alla ne della propria vita utile deve essere raccol-
to separatamente dagli altri riuti. L’utente dovrà, pertanto, conerire
l’apparecchiatura integra dei componenti essenziali giunta a ne vita
agli idonei centri di raccolta dierenziati a seconda dei riuti elet-
tronici ed elettrotecnici, oppure riconsegnarla al rivenditore al mo-
mento dell’acquisto di nuova apparecchiatura di tipo equivalente, in
ragione di uno a uno, oppure 1 a zero per le apparecchiature aventi
lato maggiore inferiore a 25 cm. L’adeguata raccolta differenziata
per l’invio successivo dell’apparecchiatura dismessa al riciclaggio, al
trattamento e allo smaltimento ambientale compatibile contribuisce
ad evitare possibili effetti negativi sull’ambiente e sulla salute e fa-
vorisce il riciclo dei materiali di cui è composta l’apparecchiatura.
Lo smaltimento abusivo del prodotto da parte dell’utente comporta
l’applicazione delle sanzioni amministrative di cui al Decreto Legisla-
tivo N ° 49 del 14 Marzo 2014.

Manuale d’istruzioni GH05 STUFA A GAS CON TURBO
dcg16.it
32
GARANZIA
Per l’apparecchio da noi messo in commercio ci assumiamo una ga-
ranzia di 24 mesi dalla data di acquisto (scontrino) solo per la parte
motore. Per la garanzia è suciente lo scontrino di acquisto. Senza
questo non sussiste il diritto né ad una sostituzione né ad una ripara-
zione gratuita.
Nel caso si ricorra alla garanzia, restituire al rivenditore l’apparecchio
completo in ogni sua parte, nell’imballaggio originale unitamente
allo scontrino.
La riparazione e/o la sostituzione di pezzi soggetti a logoramento
(*), come anche operazioni di pulizia e manutenzione non rientrano
nella garanzia e quindi sono a pagamento! La garanzia perde la sua
validità se l’apparecchio è sottomesso all’intervento di terzi.
(*): cursori, ganci impastatori, cinghie di trasmissione, telecomandi di
ricambio, spazzolini di ricambio, lame di seghe, manopole, guarni-
zioni, timer, ltri ecc.
DOPO LA GARANZIA
Quando la garanzia è scaduta, le riparazioni devono essere effettuate da
un negozio od un servizio specializzato, contro pagamento.
DCG SRL
Via G. Garibaldi 68 - 20861 Brugherio (MB)
MADE IN CHINA