DCS ADR24 User manual

THE PROFESSIONAL ACCESS DRAWERS
Installation Guide
MODELS:
ADR48 ADR30
ADR36 ADR24

1
Thank you for selecting these DCS by Fisher & Paykel Professional Access Drawers. Because of this product’s
unique features we have developed this Installation Guide. It contains valuable information on how to properly
install and maintain your new Professional Access Drawers for years of safe and enjoyable use.
To help serve you better, please fill out and submit your Product Registration by visiting our website at
www.dcsappliances.com and selecting “Customer Care” on the home page and then select “Product
Registration”. In addition, keep this guide handy, as it will help answer questions that may arise as you use your
new Access Drawers.
For your convenience, product questions can be answered by a DCS by Fisher & Paykel Customer Care Represen-
tative by phone at 1-888-936-7872, or email: customer[email protected].
FOR YOUR SAFETY
1 .Do not allow children or pets to play in or around the Access Drawers.
2 .Clean the Access Drawers regularly using a mild dish washing liquid and
water.
3 .To maintain the exterior appearance, apply a stainless steel polish to the
outside surfaces on a regular basis.
4 .Sanitize the Access Drawers surfaces each season as necessary.
5 .To prevent the formation of mold or mildew, do not store cloth napkins
or tablecloths in the Access Drawers for long periods.
6 .Cooking utensils that are stored in the Access Drawers should be stored
in sealable plastic bags and/or washed each time before re-use.
7 .Topreventpersonal injuryor damage to the drawers, do not overload
them. The maximum rating per drawer is 75 pounds.
AMESSAGE TO OUR CUSTOMERS
WARNING
1 .Do Not store or use gasoline or other flammable vapors and liquids inside or in the vicinity of this or any other
appliance.
2. An LP cylinder not connected for use shall not be stored inside or in the vicinity of this unit.
•Closing drawers may cause injury to
your hands or fingers.
• Always close or open drawers using
their handles.
• Be sure to keep hands away from
drawer edges when opening or
closing drawers.
WARNING
NOTE: Please write the Model, Code, and Serial Numbers on this page for references (located on the inside, top
right of the back wall. See Fig. 02.)
MODEL NUMBER CODE SERIAL NUMBER
NOTE: Inspect the product to verify that there is no shipping damage. If any damage is detected, call the shipper
and initiateadamage claim. DCS by Fisher & Paykel is not responsible for shipping damage.
DO NOT discard any packing material (box, pallet, straps) until the unit has been inspected.

2
TABLE OF CONTENTS
SAFETY PRACTICES AND PRECAUTIONS
1. Begin by insuring proper installation and servicing.
2. Follow the installation instructions in this manual.
3. Toextend the service life of your product, be sure to follow the use and care guidelines in this manual.
WARNING:
Do not store items of interest to children above or on the inside of any appliance. Children could be seriously injured
if they should climb ontoor into the appliance to reach these items.
SAFETY PRACTICES & PRECAUTIONS 2
MODEL IDENTIFICATION & DIMENSIONS 3
SHIPPING INSPECTION 3
INSTALLATION
Make Cutout and Installing Support Structure 4
Removing Drawers 5
Slide in Access Drawers and Mount to Support Structure 5
Re-installing Drawers 6-7
CARE & MAINTENANCE 8
WARRANTY 9-10

3
MODEL IDENTIFICATION & DIMENSIONS
SHIPPING INSPECTION
Fig. 1
Fig. 2
1. Inspect the Access Drawers to verify that there is no
shipping damage.
2. Ifany damage is detected, call the shipper and initiate
adamage claim. DCS by Fisher & Paykel is not
responsible for shipping damage.
NOTE: Donot discard any packing material (box, pallet,
straps) until the unit has been inspected.
■Operate the drawers to be sure they glide smoothly.
■Examine the drawer fronts tobe sure there are no
dents or scratches.
DIMENSIONS
MODEL D W H F
ADR48 24-1/4” 48” 22” 1-1/2”
ADR36 24-1/4” 36” 22” 1-1/2”
ADR30 24-1/4” 30” 22” 1-1/2”
ADR24 24-1/4” 24” 22” 1-1/2”
W
F
H
D
Fig. 1a
model and serial
number tag

4
INSTALLATION
MAKE CUTOUT AND INSTALL SUPPORT STRUCTURE
1. Make a cut-out in your cabinet or island with the following dimensions (Fig. 3):
2. Place 2 X 4s to provide support for the Access Drawers structure in the locations indicated in the figure below
(Fig. 4).
3. Board lengths are provided in the table below (Fig. 5).
Fig. 5
A
90º
B
C
Vent*
Vent*
Vent*
Optimal support
locations
Fig. 4
C
B
A
8-3/4” 8-3/4”
CUTOUT DIMENSIONS
MODEL A
(+0,-1/8)
B
(+1/8,-0) C
ADR48 46” 20”
24-1/2” min.
(all models)
ADR36 34” 20”
ADR30 28” 20”
ADR24 22” 20”
Note:
The cutout of each corner should be 90º for the Access Drawers to fit properly.
SUPPORTBOARD DIMENSIONS
MODEL A B C
48” 44” 1-1/2” 3-1/2”* min.
36” 32” 1-1/2” 3-1/2”* min.
30” 26” 1-1/2” 3-1/2”* min.
24” 20” 1-1/2” 3-1/2”* min.
Toensure proper drawer operation, be sure your
supportboards areflat&level.
* Island installation to use minimum of 3 vents
providing 10 sq. in. per vent (typical).
Optimal support locations.
*Dependent on application.
Fig. 6
4. When installing your support boards,
be sure they are level.
5. Check to be certain that the top
edges of your boards are level with
the bottom edge of the cut-out
(Fig. 6).
For proper support &
drawer operation, insure
that support boards are
level front to back & side
to side.
Support Board (typical) Support Boards (typical)
Front View (typical) End View (typical)
Fig. 3

5
INSTALLATION
Fig. 7
REMOVING DRAWERS
1. Once the unit has been inspected, remove the left drawers by pulling them out until their slider latch is visible.
Carefully push the latch down on the left side while pulling up on the right side and pull the drawers completely
out of the frame (Fig. 7).
2. To remove the LP tank drawer on the right, pull the drawer out and lift the end by the handle to disengage the
rollers (Fig. 8).
3. To prevent damage to surfaces, place the drawers on a stable surface on a protective towel or tablecloth.
SLIDE IN FRAME AND MOUNT TO SUPPORT STRUCTURE
1. With the help of an assistant, lift the unit off of the pallet and slide it into the cabinet cutout. Adjust for level and
fit.
2Locate mounting holes on the frame (Fig. 9 and views). Secure the unit using screws suited for the type of
cabinet material.
NOTE: Depending on the wall thickness and location of mounting holes, an additional board may be required to properly
receive the screws.
Fig. 9
Slider latch
Fig. 8
Lift
3/16"
TO 1/2"
8"
VIEW SHOWING HOLES ON
LEFT AND RIGHT SIDES
AVAILABLEFOR MOUNTING
3/4"
3/4"
VIEW SHOWING HOLES ON TOP AND BOTTOM
OF FRAMEAVAILABLE FOR ADDITIONAL SUPPORT
MOUNTING SCREWS
(not provided)
LOCATIONS

6
INSTALLATION
Fig. 10 Fig. 11
Fig. 12
3. While holding the drawer up by the handle, pull the glides from the drawer cavity out over the drawer glide until
they click (Fig. 12).
4. As you push the drawers in, you will encounter moderate resistance. Continue to push the drawer all the way in
to completethe engagement process. The drawer will now glide smoothly in & out with light effort (Fig. 13).
Drawer Cavity Glide
Drawer Glide properly Engaged.
RE-INSTALLING DRAWERS
1. Re-install the drawers by extending their guides as shown in fig. 10.
2. While holding the drawer parallel to the cabinet, carefully align & engage the ends of the glides. Slide the drawer
about an inch so that the glides are supporting the back of the drawer (Fig. 11).
Fig. 13

7
INSTALLATION
7. When connecting the LP tank to the gas line be certain that the gas pipe is routed through the recess provided
on the top of the rightside (Fig.15). Do not route the gas pipe through the opening in the back of the Access
Drawers. Once gas connections are made, test for gas leaks.
8. On models so equipped,install the two(2) racks provided intothe opening bysliding them onto the rollers on
the sidewalls of the center cavity(Fig. 16).
Fig. 14
Tank Receptacle
6. Your LP tank will be installed in the recess provided in the bottom of the right compartment (Fig. 14).
Fig. 15 Fig.16
Drain drawer
Rack & Rack Cover
Gas Pipe Recess

All parts of the Professional Access Drawers can be cleaned with hot soapy water, rinsed, dried and buffed to a shine
with a soft, heavy cloth. Always try this first, as it is the mildest cleaning procedure.
1. Use the mildest cleaning procedure first. Some brands of cleaners of the same type are harsher than others, read
their directions. A scent or a propellant can make a difference in the product, read the ingredients. Try on a small
area first.
2. To avoid marring the surface always rub metal finishes in the direction of the stainless steel polish lines (grain). The
cleaner will be more effective when used in the direction of the polish lines.
3. Use only clean sponges, soft cloths, paper towels, plastic non-metal soap pads for cleaning or scouring as
recommended in this section. (Use only soap pads with soap still in them. An empty pad can scratch.)
4. Be sure to rinse all parts thoroughly and to wipe dry to avoid water marks.
BRAND NAME CLEANERS
In this section on cleaning, the use of name brands is intended only to indicate a type of cleaner. This does not
constitute an endorsement. The omission of any name brand cleaner does not imply its adequacy or inadequacy.
Many products are regional in distribution and can be found in local markets and department stores.
MAINTENANCE
After cleaning, use a stainless steel polish, such as Stainless Steel
Magic® applied to the drawer and handle surfaces.
To maintain the smooth operation of the drawers, spray the
bearing areas with silicone spray lubricant annually .
(Fig. 17).
FREEZER PACK (OPTIONAL, KIT #70696A)
Proper Handling:
1. Placefreezer pack in freezer,layit flat.
2. Freeze overnight or a minimum of 8 hours.
3. Place frozen Freezer Pack in the steel tray on the second shelf, in
appropriate cavity of Access Drawer (Fig. 18).
The Freezer Pack is dishwasher safe. Or wash with warm soapy
water, rinse and air dry. Store flat in dry storage or in freezer.
Fig. 17
Lubrication points
(Use silicone spray
annually)
8
CARE & MAINTENANCE
Freezer Pak (optional)
Kit # 70696A
Fig.18

9
SERVICE
For warranty service, please contact your local service provider or DCS Customer Care
Representative at [phone]. Before you call, please have the following information ready:
■Model Number (located on the inside, top right of the back wall. See Fig. 02.)
■Serial Number (located on the inside, top right of the back wall. See Fig. 02.)
■Code (located on the inside, top right of the back wall. See Fig. 02.)
■Date of installation
■Abrief description of the problem
Your satisfaction is of the utmost importance to us. If a problem cannot be resolved to your
satisfaction, please write or email us at:
Write:
Fisher & Paykel Appliances, Inc.
Attention: DCS Customer Care
5900 Skylab Road
Huntington Beach, CA 92647
email: [e-mail]

10
WARRANTY
LIMITED WARRANTY
When you purchase a new DCS by Fisher & Paykel Professional Access Drawers, you automatically receive a One
Year Limited Warranty covering parts and labor for the entire product, and a Five Year Limited Warranty on all
stainless steel assemblies (parts only) for servicing within the 48 mainland United States, Hawaii, Washington
D.C. and Canada. In Alaska, the Limited Warranty is the same except that you must pay to ship the Product to the
service shop or for the service technician’s travel to your home. Products for use in Canada must be purchased
through the Canadian distribution channel to ensure regulatory compliance. Surface corrosion and discoloration
is not covered under warranty.
FISHER & PAYKEL UNDERTAKES TO:
Repair without cost to the owner either for material or labor any part of the Product, the serial number of which
appears on the Product, which is found to be defective. In Alaska, you must pay to ship the Product to the
service shop or for the service technician’s travel to your home. If we are unable to repair a defective part of the
Product after a reasonable number of attempts, at our option we may replace the part or the Product, or we may
provide you a full refund of the purchase price of the Product (not including installation or other charges).
This warranty extends to the original purchaser and any succeeding owner of the Product for products purchased
for ordinary single-family home use. All service under this Limited Warranty shall be provided by Fisher & Paykel
Appliances Inc. or its Authorized Service Agent during normal business hours.
HOW LONG DOES THIS LIMITED WARRANTY LAST?
Our liability under this Limited Warranty for the entire product expires One Year from the date of purchase of the
Product by the first consumer.
Our liability under any implied warranties, including the implied warranty of merchantability (an unwritten
warranty that the Product is fit for ordinary use) also expires One Year (or such longer period as required by
applicable law) from the date of purchase of the Product by the first consumer. Some states do not allow
limitations on how long an implied warranty lasts, so this limit on implied warranties may not apply to you.
THIS WARRANTY DOES NOT COVER:
A. Service calls that are not related to any defect in the Product. The cost of a service call will be charged if the
problem is not found tobe a defect of the Product. For example:
1. Correct faulty installation of the Product.
2. Instruct you how to use the Product.
3. Correct fault(s) caused by the user.
4. Change the set-up of the Product.
5. Unauthorized modifications of the Product.
6. Correcting damage caused by pests, for example, rats, cockroaches etc.
7. Discoloration or rust stains.
B.Defects caused by factors other than:
1. Normal domestic use or
2. Use in accordancewith the Product’s Use and Care Guide.
C. The cost of repairs carried out by non-authorized repairers or the cost of correcting such unauthorized repairs.
D. Travel Fees and associated charges incurred when the product is installed in a location with limited or restricted
access (i.e. airplane flights, ferry charges, isolated geographic areas).
E. Normal recommended maintenance as set forth in the Product’s Care & User Guide.
F. Defects to the Product caused by accident, neglect, misuse, fire, flood or Act of God.

11
WARRANTY (continued)
If you have an installation problem contact your dealer or installer. You are responsible for providing adequate
electrical, exhausting and other connection facilities. We are not responsible for consequential or incidental
damages (the cost of repairing or replacing other property damaged if the Product is defective or any of your
expenses caused if the Product is defective). Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
HOW TO GET SERVICE
Please read your Use and Care Guide. If you then have any questions about operating the Product, need the
name of your local DCS Authorized Service Agent, or believe the Product is defective and wish service under this
Limited Warranty, please contact your dealer or call us at:
TOLL FREE 1-888-936-7872 or contact us through our web site: www.dcsappliances.com.
You may be required to provide reasonable proof of the date of purchase of the Product before the Product will
be serviced under this Limited Warranty.
COMMERCIAL USE
This warranty applies to appliances used in residential applications; it does not cover their use in commercial
situations.
NO OTHER WARRANTIES
This Limited Warranty is the complete and exclusive agreement between you and Fisher & Paykel Appliances Inc.
regarding anydefectin the Product. None of our employees (or our Authorized Service Agents) are authorized to
make anyaddition or modification tothis Limited Warranty.
Warrantor: Fisher & Paykel Appliances, Inc.
Ifyou need further help concerning this Limited Warranty, please call us at the above number, or write to:
Fisher & Paykel Appliances, Inc.
Attention: DCS Customer Care
5900 Skylab Road,Huntington Beach, CA92647
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
Fisher & Paykel Appliances Inc. is a leading manufacturer of premium quality cooking and specialty appliances
under the Fisher & Paykel and DCS by Fisher & Paykel brands.

12
NOTES

LES TIROIRS PROFESSIONNELS
Guide d'installation
MOD È LES :
ADR48 ADR30
ADR36 ADR24

1
Nous vous remercions d'avoir choisi ces tiroirs professionnels DCS by Fisher & Paykel. Nous avons conçu ce
Manuel d'installation pour expliquer les fonctions uniques de ce produit. Ce manuel contient des informations
extrêmement utiles sur la façon correcte d'installer vos nouveaux tiroirs professionnels et d'en faire l'entretien.
Vous pourrez ainsi en profiter pendant des années en toute sécurité.
Aidez-nous à mieux vous servir en remplissant l'enregistrement de produit et en nous le soumettant depuis notre
site Web à www.dcsappliances.com. Sélectionnez « Customer Care » sur la page d'accueil puis « Product
Registration ». De plus, gardez ce manuel à portée de main afin de rapidement trouver réponse à vos questions
durant l'utilisation de vos nouveaux tiroirs.
Si vous avez des questions au sujet de notre produit, communiquez avec un représentant du service à la clientèle
DCS par téléphone : 1-888-936-7872, ou par email: [e-mail].
REMARQUE :Inspecter le produit pour vérifier qu’il n’a pas été endommagé pendant l’expédition. En cas de
dommages, contacter le transporteur et entamer une déclaration pour dommage. DCS by Fisher & Paykel n’est en
aucun cas responsable des dommages pendant l’expédition.
Ne pas jeter le matériau d’emballage (boîte,palette,sangles) avant d’avoir inspecté l’unité.
POUR VOTRE SÉCURITÉ
1. Ne laissez pas des enfants ou des animaux de compagnie jouer à l'intérieur ou autour des tiroirs.
2. Nettoyez les tiroirs périodiquement avec un détergent liquide pour
vaisselle doux et de l'eau.
3. Pour préserver l'aspect extérieur, appliquez un produit à polir pour acier
inoxydable sur les surfaces extérieures sur une base régulière.
4. Désinfectez les surfaces des tiroirs à chaque saison au besoin.
5. Pour éviter la formation de moisissure, évitez de ranger des serviettes de
table en tissu ou des nappes dans les tiroirs pendantdes périodes
prolongées.
6. Les ustensiles de cuisson rangés dans les tiroirs doivent être placés dans
des sacs en plastique scellables ou lavés chaque fois avantd'êtreréutilisés.
7. Pour éviter des blessures corporelles ou ne pas endommager les tiroirs,
évitez de les surcharger. Le poids maximum par tiroir est de 34 kg (75 lb).
AL'INTENTION DE NOS CLIENTS
AVERTISSEMENT
1. Évitez de stocker ou d'utiliser de l'essence ou tout autre liquide et vapeur inflammable à l'intérieur ou à proximité de
cet appareil ou de tout autre.
2. Évitez de ranger une bouteille de gaz propane (qui n'est pas connectée car non utilisée) à l'intérieur ou à proximité de
cet appareil ou de tout autre.
.
• Closing drawers may cause injury to
your hands or fingers.
• Always close or open drawers using
their handles.
• Be sure to keep hands away from
drawer edges when opening or
closing drawers.
WARNING
REMARQUE : Veuillez noter les numéros de modèle, code, et de série sur cette page pour information (Voir Fig. 02.)
NUMÉRO DE MODÈLE CODE NUMÉRO DE SÉRIE

2
TABLE DES MATIERES
MESURES DE SECURITE ET DE PRECAUTION
1. Commencez par vous assurer que l'installation et l'entretien sont effectués correctement.
2. Suivez les instructions d'installation du manuel.
3. Pour prolonger la durée de vie utile du produit, suivez les consignes d'utilisation et d'entretien de ce manuel.
AVERTISSEMENT :
Évitez de ranger au-dessus ou à l'intérieur d'un quelconque appareil des articles pouvant attirer les enfants. Ceux-ci
peuventse blesser sérieusement s'ils grimpent sur ou à l'intérieur de l'appareil pour atteindre l'objet en question.
MESURES DE SECURITE ET DE PRECAUTION 2
IDENTIFICATION DU MODELE ET DIMENSIONS 3
INSPECTION APRES LIVRAISON 3
INSTALLATION
Effectuer la découpe et installer la structure de support 4
Retrait des tiroirs 5
Enfoncer les tiroirs et les monter sur la structure de support 5
Réinstallation des tiroirs 6-7
ENTRETIEN ET MAINTENANCE 8
GARANTIE 9-10

3
IDENTIFICATION DU MOD È LE ET DIMENSIONS
INSPECTION APRES LIVRAISON
Fig. 1
Fig. 2
1. Inspectez les tiroirs pour vous assurer qu'ils n'ont subi
aucun dommage durant le transport.
2. Lecas échéant, appelez le transporteur et soumettez
une réclamation pour dommages. DCS by Fisher &
Paykel n'est pas responsable des dommages subis
durantle transport.
REMARQUE : Ne jetez aucun matériel d'emballage (boîte,
palette, sangles) avant d'avoir inspecté l'appareil.
■Faites fonctionner les tiroirs pour vous assurer qu'ils
glissent correctement.
■Examinez le devantdes tiroirs pour vous assurer qu'il
n'yaaucune bosse ou égratignure.
DIMENSIONS/COTES
MODELE PLHC
ADR48 54 cm 121,9 cm 56 cm 3,8 cm
ADR36 54 cm 91,4 cm 56 cm 3,8 cm
ADR30 54 cm 76,2 cm 56 cm 3,8 cm
ADR24 54 cm 61 cm 56 cm 3,8 cm
W
F
H
D
Fig. 1a
Numérodemodèle
et de série

4
INSTALLATION
EFFECTUER LA DECOUPE ET INSTALLER LA STRUCTURE DE SUPPORT
1. Effectuez une découpe dans votre armoire ou îlot avec les dimensions suivantes (Fig. 3) :
2. Placez des pièces 2 x 4 pour fournir un support à la structure des tiroirs aux emplacement indiqués sur la figure
ci-dessous (Fig. 4).
3. La longueur des planches est indiquée dans le tableau ci-dessous (Fig. 5).
Fig. 5
A
90º
B
C
Vent*
Vent*
Vent*
Optimal support
locations
Fig. 4
C
B
A
8-3/4” 8-3/4”
DIMENSIONS DES DECOUPES
MODELE A
(+0,-0,3)
B
(+0,3,-0) C
ADR48 116,8 cm 50,8 cm 62 cm
(24 1/2 po)
min.
(tous les
modèles)
ADR36 86,4 cm 50,8 cm
ADR30 71,2 cm 50,8 cm
ADR24 56 cm 50,8 cm
Remarque :
La découpe de chaque coin doit être à 90º pour que les tiroirs rentrent correctement.
DIMENSIONS DES PLANCHES DE SUPPORT
MODELE A B C
48” 121,9 cm 3,8 cm 8,9 cm* min.
36” 91,4 cm 3,8 cm 8,9 cm* min.
30” 76,2 cm 3,8 cm 8,9 cm* min.
24” 61 cm 3,8 cm 8,9 cm* min.
Afin d'assurer le bon fonctionnementdes tiroirs, assurez-vous
que les planches de supportsontplates et de niveau.
* Prévoir pour l'installation en îlot 3 évents
minimum à raison de 64 cm2(10 po2)par évent
(installation typique).
Emplacement de support
optimal.
*En fonction de l'application.
Fig. 6
4. Lors de l'installation des planches de
support, assurez-vous qu'elles sont
de niveau.
5. Vérifiez que les bords supérieurs des
planches sont au même niveau que
le bord inférieur de la découpe.
(Fig. 6).
Pour permettre un
support et un fonction-
nement adéquat des
tiroirs, assurez-vous que
les planches de support
sont de niveau de l'avant à
l'arrière et d'un côté à
l'autre.
Planche de support (typique)
Planches de support
(typique)
Vue de face (typique) Vue de l'extrémité (typique)
Fig. 3

5
INSTALLATION
Fig. 7
RETRAIT DES TIROIRS
1. Une fois l'appareil inspecté, retirez les tiroirs gauches en tirant jusqu'à ce que le verrou de glissière soit visible.
Enfoncez soigneusement le verrou du côté gauche tout en soulevant du côté droit, et tirez les tiroirs pour les
sortir complètement du châssis (Fig. 7).
2. Pour enlever le tiroir du réservoir de propane sur le droit côté, tirez le tiroir et soulevez l'extrémité par la poignée
pour dégager les roulettes (Fig. 8).
3. Pour éviter d'endommager les surfaces, placez les tiroirs sur une surface stable sur une serviette ou une nappe de
protection.
ENFONCER DANS LE CADRE ET MONTER SUR LA STRUCTURE DE SUPPORT
1. Avec l'aide d'un assistant, soulevez l'appareil de la palette et glissez-le dans la découpe d'armoire. Effectuez
l'ajustement nécessaire.
2Repérer les trous de montage sur le cadre (Fig. 9 et illustrations). Fixez l'appareil à l'aide de vis appropriées pour
le type de matériau des armoires.
REMARQUE : Selon l'épaisseur du mur et l'emplacement des trous de montage, ajoutez au besoin une planche supplé-
mentairepour permettre une bonne prise des vis.
Fig. 9
Verrou de glissière
Fig. 8
Soulevez
0,5 à1,3 cm
(3/16 à1/2 po)
8"
TROUS DE MONTAGE
DU CÔTÉGAUCHE
ET DROIT
1,9 cm
(3/4 po)
1,9 cm
(3/4 po)
TROUS DE SUPPORT SUPPLÉMENTAIRE SUR
LE HAUT ET LE BAS DU CADRE
VIS DE MONTAGE
(non fournies)
EMPLACEMENTS