Decofire Milano Series Maintenance and service guide

DÉCOFIRE
Page 1
–Milano Series FIRE TABLES –
Assembly, Safety & Operating Instructions
FOR OUTDOOR USE ONLY
READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY
OR USE. KEEP INSTRUCTIONS IN A SAFE PLACE
FOR FUTURE REFERENCE. THIS APPLIANCE IS NOT
DESIGNED FOR COMMERCIAL USE
WARNING
Improper installation, adjustment, alteration, service
or maintenance can cause injury or property damage.
Read the owner’s manual thoroughly before installing or
servicing this equipment. If the information in this manual is
not followed exactly, a re or explosion may result causing
property damage, personal injury or loss of life.
WARNING
Do not store or use any ammable liquids or gases in the
vicinity of this appliance. An LP gas cylinder not connected
for use must not be stored in the vicinity of this appliance.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open ame or ignition source
3. If odour continues, keep away from the appliance and
immediately call your local re department
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide, which has no
odour. Using it in an enclosed space can kill you. Never use
this appliance in an enclosed space such as a tent, car or
basement. Do not bring this appliance indoors.
WARNING
The glass ame tube may break if it is wet while in use;
never use the appliance while it’s raining or wet conditions
are present. Do not splash any liquid on the appliance while
it is operating or hot.

990mm
500mm
500mm
405mm
85mm
260mm
350mm
490mm
358mm
730mm
990mm
880mm 880mm
405mm
215mm
260mm
350mm
490mm
535mm
730mm
990mm
610mm
1220mm
435mm
260mm
260mm
350mm
490mm
872mm
297mm
730mm
Page 2
Specifications & Dimensions
Décofire (XXXXXX) Series Fire Tables
Specifications DF102040
Fire Column DF102041 Fire Table DF102042 Fire Table
Gas type LPG - ONLY LPG - ONLY LPG - ONLY
Gas consumption 24 MJ/Hr 36 MJ/Hr 452 MJ/Hr
Operating pressure 2.75kPa 2.75kPa 2.75kPa
Injector size 1.38 mm 1.68 mm 2.09 mm
Fire Column - DF102040
FireTable - DF102041
FireTable - DF102042

Page 3
IMPORTANT SAFETY WARNINGS
• THIS APPLIANCE IS DESIGNED AND INTENDED FOR OUTDOOR USE ONLY!
• This appliance shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
• This appliance shall not be installed or used indoors, inside buildings, sheds or garages or any other enclosed area.
• DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
• DO NOT place, use or store any ammable liquid or gas fuels or fuel containers within the vicinity of this appliance and
always ensure that any fuel containers or cylinders nearby are sealed or shut off to prevent escaping vapour.
• This appliance is designed and approved for use with LPG / Propane Gas Only. (Cylinder and gas sold separately)
• This appliance is NOT approved for use with Natural Gas. Do Not attempt to convert this appliance to Natural Gas.
Converting this appliance to Natural Gas is dangerous. Unauthorised conversion of this appliance will void the
manufacturer’s warranty.
• DO NOT place any article on or against this appliance. NEVER hang clothes or ammable items over or on this appliance.
• Children & adults must be alerted to the hazards of high surface temperatures and risk of burns and igniting of clothing.
• Children should be carefully supervised when they are in the area of the appliance.
• DO NOT operate this appliance unless it is fully assembled.
• This appliance must be maintained and serviced in accordance with the instructions and recommended service intervals
supplied in this instruction manual. Any repairs should be undertaken by a qualied service technician.
• This appliance should be inspected and serviced at least every 3 years by a qualied service technician.
• It is important that all control compartments, burners and circulating air passages of the appliance be kept clean for
continued safe operation.
• Only use the regulator and hose assembly provided with this appliance. Use only genuine replacement parts.
All replacement parts used must be of the same specication as originally supplied with this appliance.
GENERAL SAFETY WARNINGS
• Ensure this appliance is placed on a rm, level surface.
• Do Not use the appliance if it has been exposed to rain or water. Always allow appliance to dry before operating.
• Check the weather forecast before using this appliance. Don’t use your appliance during high winds. Avoid installing or
operating this appliance, where a direct draft may affect or fan the ames.
• Make sure that the re is completely extinguished before you leave this appliance unattended.
• Do not disassemble or modify this appliance in any manner other than as described within these instructions.
• Installation clearance requirements must be adhered to. Please read the section on installation clearances before installing
or placing this appliance.
• Do not cover or surround this appliance with insulating materials.
• The installation of this appliance must adhere to local codes or AS/NZS: 5601
• Never remove or reinstall a gas cylinder from this appliance while it is in use - always turn off all valves and controls before
changing over the gas supply cylinder.
• Never use a naked ame to check for gas leaks.
• Discontinue use if any part of the gas cylinder is damaged. Rust and dents may be hazardous and should be inspected by a
gas supplier or cylinder inspection station.
• Do not operate appliance until all parts are fully assembled.
• Do not paint or color any part of this appliance.
• Never leave this appliance unattended while in use.
• Keep a safe distance to avoid burning skin or clothing.
• Do not sit on or rest hands or feet on this appliance.
• Never use the appliance in spaces which may contain volatile or airborne combustibles.
• If the ame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial lighting procedure.
Once you have a ame started, hold down the control knob for 1 minute.
• Do not spray appliance with water when it is operating. Do not operate appliance if any part has been submerged in water.
• Do not disconnect any part of this appliance while it is in use.
• If this appliance is being stored indoors, detach the gas cylinder and store in a safe place -ensure all gas valves and controls
are turned to the off position.
• Do not install or operate this on a boat or vehicle.
• Always remove any protective cover (polyester, vinyl or other type of cover).
• Do not set the protective cover over the appliance until it is turned off and completely cooled down.
• Always check for leaks if the appliance has not been used for an extended period.
• Inspect the gas hose and all connections to the gas cylinder prior to each use.
• In case of high winds, you may be required to secure this appliance to the ground to prevent the unit falling over.

Page 4
OPERATING SAFETY WARNINGS
• Always follow lighting instructions carefully.
• This appliance is not intended for cooking.
• Appliance may be hot while in use, do not attempt to move it while in use.
• Always observe any local or state re warnings.
• Do Not use gasoline, petrol, ethanol, alcohol, turpentine, kerosene, lighter uids or any other liquid fuels in conjunction
with this appliance.This is dangerous and may result in an explosion.
• While this appliance is operating or hot, do not touch the main heating surface or immediate surroundings as these areas
may be hot and could cause burns.
• Do not use this appliance for any purpose other than its intended use.
• To prevent accidental re and / or smoke damage, remove all packaging before lighting or operating this appliance.
• Do not heat any unopened plastic, glass or metal containers on or in this appliance. Pressure may build up and cause the
container to burst, resulting in serious personal injury or death, property damage or damage to this appliance.
• Never move this appliance when it is operating or hot.
• Do not use this appliance while under the inuence of alcohol, prescription or non-prescription drugs or any substance
that may impair sound judgment.
• Avoid wearing loose clothing while operating this appliance.
CHILD & PET SAFETY WARNING
• Never let children operate this appliance without close supervision. Children must be supervised while near this unit
• Never leave this appliance unattended while in use. Monitor any child or pet activities around this appliance at all times.
• Gas appliances contain hot working surfaces that, if touched, may cause skin burns or scalding.
• Never leave children or pets unattended in the vicinity of where this appliance is being used.
• Do not store items of interest to children on, around or below this appliance. Children climbing on this appliance, to reach
items, could damage this appliance or be burned or seriously injured.
• Never allow children to sit or stand on any part of this appliance.
• We recommend the use of a re screen or guard to prevent children or pets from coming into direct contact with the
surfaces of this appliance while it is in use or hot.
MAINTENANCE & REPAIR SAFETY WARNINGS
• This appliance should be inspected and cleaned regularly in accordance with the instructions supplied in this manual.
• Always check this appliance prior to each use - do not use this appliance if there is a fault.
• All installation and repair should be done by a qualied service technician.
• Unless specically recommended in this manual, do not attempt to repair or replace any part of the appliance yourself.
• Only use genuine replacement parts.
• Do not operate the product if it has been dropped or damaged in any manner. Call our customer service number for
information on examination or mechanical repair or adjustment of this product.
• Any guard or other protective device removed for servicing the appliance shall be replaced prior to operating the
appliance.
• It is imperative that the control compartment, burners and circulating airways of the appliance are kept clean.
IN THE EVENT OF ACCIDENTAL FIRE
• In the event of an accidental re, if safe to do so, immediately turn this appliance off at the main control and then shut off
the cylinder control valve.
• For emergency purposes, we recommend the installation of an approved re extinguisher in the vicinity of where this
appliance is installed.
UNPACKING YOUR APPLIANCE
• Due to the weight - this product may require two people to lift the components from the carton.
• Place a sheet or blanket on the ground to protect the surfaces of this appliance when unpacking and handling.
• Carefully remove all components from the carton and remove all packaging materials from the product prior to rst use.
• Before beginning assembly of product, make sure all parts are present. Compare parts with components and hardware
contents list. If any part appears to be missing or damaged, don’t use this product and call customer service immediately.

Page 5
Minimum Clearances To Combustibles
Combustible materials are materials such as wood, paper plant bres
some plastics. e.g. any material that is capable of being ignited.
WHEN CERTAIN MATERIALS OR ITEMS ARE STORED ABOVE, BESIDE OR UNDER THIS APPLIANCE
WHILE IN USE, THEY MAY BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED.
610 MM
1 MTR 1 MTR
Above this appliance:
Minimum of 610mm to combustible materials. NOTE: DO NOT
use this appliance under any awning or pergola if there is a risk of
the structure or materials igniting or being damaged by the heat.
Around this appliance:
Minimum of 1metre to combustible materials.
INSTALLATION GUIDELINE
Only use this appliance in an above ground open-air situation with natural ventilation, without stagnant areas, where gas
leakage and products of combustion are rapidly dispersed by wind and natural convection. Any enclosure in which the
appliance is used must comply with one of the following:
WHERE TO PLACE YOUR APPLIANCE
1. An enclosure with walls on all sides,
but at least one permanent opening at
ground level and no overhead cover
2. Within a partial enclosure that
includes an overhead cover and no
more than two walls
3. Within a partial enclosure that includes an overhead cover and more than two walls, the following will apply:
(i) at least 25% of the total wall area is completely open, and
(ii) at least 30% of the remaining wall area is open and unrestricted (see Example 4 & 5).
(iii) In the case of balconies, at least 20% of the total wall area shall be and remain open and unrestricted.

Page 6
APPLIANCE FEATURES
Cylinder
Compartment
Adjustable
Feet (x4)
Cylinder
Enclosure
Access Panel
Flame Control
Starter Button
Protective Cover
Glass Surround
Glass Table Top
Burner Tray
Burner Ignition Module

Main Body
Hose &
Regulator
Lava Rock Pack x 1
Adjustable
Feet x 4
1.5V (AAA)
Battery
Glass Mounting
Brackets x 4
Upper Glass
Connectors x 4
Protective
Cover x 1
Fire Column
DF102040 x 4 Pcs
Glass Surround Panels Glass Mounting Hardware
Fire Table
DF102041 x 4 Pcs
Fire Table
DF102042 x 4 Pcs
Cylinder
Enclosure
Access Panel
M6 x 30mm
Screws x 4
Page 7
OTHER PARTS TO BE LISTED
AND LISTED HERE
COMPONENTS AND HARDWARE

OFF
Page 8
ASSEMBLY & SETUP
Step 2.
Check that the control knob is turned to the “OFF”
position before starting any assembly.
Step 1.
Fit the adjustable feet. Insert feet to each bottom
corner. Screw all feet - all the way in and then adjust
each foot to level the appliance.
Step 3.
Remove the cylinder enclosure panel from the main
body of the appliance. Place the gas cylinder (not
included) into the metal stand inside the main body.

Cylinder
Valve
Regulator
Turn anti-clockwise
to connect
Page 9
Step 6.
Replace the enclosure panel.
Step 5.
Once the POL connection is secured, make sure the gas
cylinder sits on the metal stand inside the main body.
Hand tighten the wing screw on the outer part of the
metal stand to secure the gas cylinder.
ASSEMBLY & SETUP
Step 4.
Attach the appliance regulator to the gas cylinder.
Ensure the valve is clean and free of any debris.
Note:The POL connector is left hand threaded.You
must turn the handwheel anti-clockwise to tighten.
Hand tighten only. Do not use tools.

OFF
Page 10
Step 7.
Unscrew the cap on the electronic igniter. Insert a AAA
battery into the housing. Ensure the positive end of the
battery faces outwards.
Screw the cap back on and tighten rmly.
ASSEMBLY & SETUP
Step 8.
Pour the Lava rock into the burner tray. Spread
the rock evenly around the burner tray.
To ensure trouble free
operation of the burner,
keep the ignition probe
shield clear of any Lava
rock material at all times.
Step 9.
Fit the glass surround panels. (Applies to all models)
A. Attach the 4 mounting brackets
to the top re table. Note the
correct orientation of each bracket.
Secure the brackets using the
M6 x 30mm screws.
Do not overtighten.
B. Fit the glass panels to each
side. Ensure the panels are
correclty positioned between
each set of brackets.
C. Fit the upper glass brackets
to each corner.

Bubbles indicate
a leak present
Leak test the gas
gas hose and each
connection point
Page 11
Appliance, Gas Controls and Burner
Inspect all major components on the appliance:
• Check the burner, glass tube and reector for any damage or build up of carbon, spider webs or nests etc.
• Check that the wire guard is secured and undamaged.
• Check the appliance controls - (ame adjustment control and starter button) - the ame adjustment control should rotate
smoothly and the starter button, when pressed, should cause a spark to occur at the burner ignition probe.
• Ensure the ignition probe is clear of dust or debris.
Gas Hose & Regulator - Gas Line Connections
• Inspect the appliance gas hose and regulator for abrasion, cuts or other damage. If there are signs of wear, abrasion or
damage, you must replace the hose and regulator.
• If the gas hose / regulator has been disconnected from the appliance for a period of time - inspect the POL connector to
ensure it is free of any dirt, spider webs or nests etc. If not cleared, these elements can cause a blockage that will prevent
the appliance from functioning.
Gas Cylinder & Cylinder Valve
• Inspect the gas cylinder and cylinder valve for any signs of wear or damage.
• The gas cylinder should be clean and show no signs of rust or dents. If the cylinder is corroded or has sustained a dent it
will need to be checked at an authorised cylinder inspection station. (Or swap over your cylinder for a freshly lled one at
your nearest cylinder exchange retailer).
• If the gas cylinder has been disconnected from the appliance for a period of time - inspect the cylinder valve / outlet to
ensure it is free of any dirt, spider webs or nests etc. If not cleared, these elements can cause a blockage that will prevent
the appliance from functioning.
Gas Leak Test
• Before using the appliance each time, it is advisable to
perform a leak test on each gas line connection.
• Prior to performing a leak test be sure there are no live
ignition sources present such as a naked ame or pilot
light for another gas appliance.
• Never ever check for gas leaks with a naked ame.
Leak Test Procedure
1. Connect the appliance hose & regulator to the gas
cylinder and make sure the valve on the gas cylinder is
turned off.
2. Check that the gas control on the appliance is turned to
the ‘OFF’ position.
3. Brush a mixture of detergent and water on all
connections. including the Hose, Regulator, POL
Connection, Cylinder Valve.
4. Turn the gas cylinder valve on. If bubbles form on any
connection point along the gas line, this is an indication
that a leak is present.
5. If you smell gas or a leak is discovered, turn the gas
cylinder valve off, disconnect the regulator from the gas
cylinder and do not use the appliance until the leak is
repaired.
OPERATION

OFF
OFF
OFF
OFF
OFF
HIGH
LOW
Page 12
WARNING: If the lighting instructions are not followed directly a re or explosion may occur resulting
in property damage, personal injury or death.
Lighting the Appliance
1. Make sure the appliance control knob is in the ‘OFF’ position.
2. Turn on the gas cylinder valve.
3. Push in the ame control knob and turn it to the ‘LOW’ position.
Keep holding down the control knob in, while at the same time...
Push and hold in the electronic igniter button until the burner is
alight. (When lighting the appliance for the rst time, or after recently
relling the gas cylinder, this process may take longer as air needs to
be purged from the gas hose).
4. If ignition doesn’t occur within a few seconds, release the control
knob and rotate it to the ‘OFF’ position. Wait for 5 minutes for gas
to clear and then repeat the above lighting instructions.
5. Once the burner is alight, the ame intensity can be adjusted by
rotating the knob between the ‘LOW’ and ‘HIGH’ positions.
2.
2.
3. 4.
5.
1.
1.
Extinguishing the Appliance
1. Push in and turn the ame control knob to the ‘OFF’ position.
2. Always turn the gas cylinder valve off - especially if the appliance is
not to be used for some time.
Important Note - Lava Rock
During manufacture, we take steps to preheat the Lava rock to expel
any residual moisture before it is packed with the appliance.
Lava rock is a porous material that can absorb moisture.When heated,
any moisture trapped inside the Lava rock may expand and cause the
Lava rock to crack or pop.
Lava rock should therefore be kept dry at all times - cover the
appliance when not in use. If the Lava rock becomes wet at any time
(Rain or, an accidental spill for example) do not use the appliance until
the Lava rock has thoroughly dried out.
Avoid standing directly over the burner when lighting or using the
appliance at any time.
OPERATION
Flame Colour & Height
20 minutes after igniting the burner, the ame should appear as a
yellow/blue color, with a height between 70mm - 250mm.

Page 13
Problem Cause Solution
Burner will not light
(Electric starter faults)
Igniter electrode pin and / or burner
are wet
Dry off with a soft cloth.
Igniter battery is incorrectly inserted Check which direction the battery is inserted.
Igniter battery is exhausted / dead Replace with a fresh 1.5V AAA battery .
Igniter electrode pin is broken Replace the electrode - Contact Décore.
Igniter electrode wire is loose or
disconnected
Reconnect contact wire to the igniter box.
Electrode wire is shorting between
valve
Check for source of short - replace electrode wire if
faulty - Contact Décore.
Burner will not light
(Gas supply faults)
No gas ow / no gas Check cylinder valve is turned on.
No gas ow / no gas Cylinder low or empty - rell or swap over cylinder.
No gas ow / no gas Regulator / hose not connected - check all
connections, leak test and resume lighting and
operation procedures.
Obstructed gas ow Check all hoses for kinks and bends.
Burner ports obstructed - dirt or
debris
Turn off appliance ame control and cylinder valve.
Insert an opened paper clip (or similar item) into each
of the burner ports to clear them out.
Burner ports obstructed -
Bugs, spiders, webs or nests
Turn off appliance ame control and cylinder valve.
Insert an opened paper clip (or similar item) into each
of the burner ports to clear them out.
Use caution when clearing any web or nest.
Burner emits smoke Flame obstructed at burner ports Check that all burner ports are free of any small
burner media (Lava rock or pumice stone etc).
Regulator hose is kinked Check hose and remove any bends or kinks.
Sudden drop in gas ow No gas ow / no gas Check cylinder valve is turned on / fully open.
No gas ow / no gas Cylinder low or empty - rell or swap over cylinder.
Excess ow or safety shut off device
safety valve has been activated
(If tted)
Turn the ame control knob to the ‘OFF’ position.
Turn off the cylinder valve.
Check for the reason why the safety device has
activated before resetting the safety device. (Follow
the manufacturers instructions).Then turn on the gas
cylinder valve and restart the appliance as per the
lighting procedure in this manual.
Burner will not stay
alight / Flame blows out
easily
Flame obstructed at burner ports Check that all burner ports are free of any small
burner media (Lava rock or pumice stone etc).
Strong ambient breeze present. Increase ame to ‘HIGH’
No gas ow / no gas Check cylinder valve is turned on / fully open.
No gas ow / no gas Cylinder low or empty - rell or swap over cylinder.
IN THE EVENT OF FAULT
Most problems can be easily solved by using the trouble shooting guide below to determine the cause and solution before
calling our customer service team.

Page 14
CARE & CLEANING
• Never clean this appliance when it is hot - always allow
the appliance to cool completely before cleaning or
maintenance.
• Before performing any maintenance always shut off all gas
controls and valves and disconnect the gas cylinder from
the appliance.
• Do not use high pressure water blasting devices to clean
the surfaces of the appliance body as this may damage or
remove the surface coatings.
• Always check any cleaning product on a small area of
the underside of the product to conrm it is safe to
use. Note: Permanent damage may occur if powder or
solvent cleaners come in contact with painted or plastic
components on this appliance.
• Avoid using harsh chemical cleaners, sprays or highly
abrasive cleaning tools.
• Harsh weather conditions may cause stubborn stains,
discoloration and possibly rust pitting.
• Carbon deposits may pose as a re hazard; clean the
reector and inside of the glass tube with soap and water
if any carbon deposits are present.
Care: Body - Painted Finishes
Wipe the appliance over with a soft damp cloth and mild
detergent if required. Rinse with clean water and dry off all
components with a soft cloth before using appliance.
Care: Glass Components
Regularly clean the glass tube with a glass cleaner and rinse
with clean water and then dry the glass with a soft cloth.
Ensure the glass tube is completely dry before reinstalling
into the appliance.
Care: Stainless Steel / Aluminium Components
Regularly clean the visible stainless steel or aluminium
components with a suitable approved cleaner. Follow the
manufacturers instructions for cleaning and then rinse the
components with clean water and then dry the components
with a soft cloth. Ensure all components are completely dry
before using the appliance.
STORAGE
When not in use, this appliance must be protected from
exposure to the elements: e.g. Sun,Wind, Rain, Dust, Snow
and Ice.
Cover this appliance at all times when not in use or move
this appliance to a covered outdoor space or store the
appliance in a dry environment, for example, a garage or
suitable storage space.
If this appliance is being stored indoors, the gas cylinder
must be turned off at the cylinder valve and the gas cylinder
must be disconnected from the appliance. It is generally
recommended that any gas cylinder - when not in use - be
stored outdoors in a secure, protected and well ventilated
area.
SPARE PARTS
Where components require replacement these should be
obtained from the original supplier - or as advised by your
gas service technician.
Using non manufacturer approved parts or accessories may
result in a defective condition and void the warranty of this
appliance.
CLEANING, MAINTENANCE
& SERVICING SCHEDULE
Service Item Recommended
Interval
Major appliance
inspection and service
This appliance should be
inspected and serviced
by a qualied gas service
technician.
2 years
Cleaning: Appliance Body,
Glass Flame Tube, Mesh / Wire
Guard, Burner, Reector.
6 months or, more
frequently if required.
Gas leak test. 1-2 months or,
Whenever gas cylinder is
relled or,
If the hose and regulator
has been disconnected.
Inspect burner and ame
control operation.
12 months.
Check ignition / starter
system and battery.
12 months.
Inspect hose and regulator
for damage, abrasion, cuts or
other damage.
6 months or, whenever
the cylinder is relled.
Inspect the POL connector
and ‘O’ Ring.
12 months or, whenever
the cylinder is relled.
Inspect the glass ame tube
for damge or cracks.
6 months.
Inspect appliance guard for
damage - ensure guard is
secured to appliance.
6 months.
Inspect gas cylinder. Check
for corrosion or damage to
cylinder and valve.
Check valve operation.
6 months or,
Whenever cylinder is
relled or reconnected
to the appliance.

Page 15
ENVIROSTONE®SURFACE CARE
The surface material of this appliance has been sealed with a patented treatment to prevent staining and moisture absorption,
but it does require proper maintenance to ensure the integrity of the surface.
The following recommendations will assist in maintaining your Envirostone®surface for many years:
Clean any spills immediately to prevent permanent surface staining or damage.
Blot any liquid spills with a clean, dry cloth or sponge to avoid spreading of the spill to the rest of the appliance.
Clean your appliance surfaces with a soft, clean cloth or sponge. Mix a solution of warm clean water and mild dish soap to
remove any surface dirt or mild spills. Rinse all soap solution off of the appliance surfaces and dry completely to avoid water
spots. Regularly cleaning the appliance surfaces will aid in a longer lasting product.
Do not use petroleum-based or abrasive cleaning products. Do not use any harsh brushes when cleaning the appliances
surfaces.
Do not slide products across the glass table top or appliance surfaces to avoid permanent scratching and damage.
Always use protective mats, place mats or coasters to avoid scratching or staining the table top surface. These protective
products will help absorb sweating on cool beverages and will block out any heat rings from appearing beneath a warm mug
or plate.
When placing hot dishes on an Envirostone®surface, always use mats or hot pads.
Envirostone®surface must be covered at all times when not in use. Cover your product with the weather cover supplied or a
suitable outdoor furniture cover when not in use to protect it from the elements.
In extremely cold climates or regions, store your appliance indoors during winter months. Avoiding extreme cold
temperatures will prevent cracking of the body and tabletop.

Page 16
WARRANTY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.You are entitled to a replacement or
refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benets
to the consumer given by this warranty are in addition to other rights and remedies of the consumer under the law in relation to the
goods and services to which the warranty relates.
Term
Mayo Hardware Pty Ltd warrants this Décore™ product to be free from manufacturing defects for a period of 12 months
commencing from the date of purchase.
Conditions
• This warranty covers manufacturer’s faults and defects only.
Items not covered by this warranty:
• Working surfaces or components subject to normal wear and tear - unless it is a clear defect or manufacturing fault.
• Deterioration as a result of exposure to the elements.
• Damage caused by adverse weather conditions, fair wear and tear, accidents, misuse, negligence, re, ood, hail, earthquakes
or other natural disasters
• Alternations or repairs undertaken by an unauthorised service person.
• Modication of the appliance and and any of its components.
• Use of any non specied component or replacement part.
• Use or installation of this appliance - other than what is described in the user instructions (instruction manual)
• Removal of any safety device or guard.
• This warranty does not extend to commercial use of the product.
If a defect occurs during the warranty period and you wish to obtain a replacement, please forward to Mayo Hardware Pty
Ltd a written description and photographs of the claimed defect, and a copy of the original receipt or proof of purchase.
Full documentation must be provided within 28 days of the occurrence that leads to a claim. Any expenses incurred by the
consumer in making the warranty claim are at the cost of the consumer.
Mayo Hardware Pty Ltd reserves the right to determine manufacturing faults at their discretion. In the interests of ongoing
product development and improvement the manufacturer reserves the right to discontinue or change specications or
designs at any time without notice and without incurring obligations.
For warranty or technical support, please call Mayo Hardware Pty Ltd.
Customer Service: 1300 360 211 Web: decoreheating.com.au
© Copyright 2018 Mayo Hardware Pty Ltd. All rights reserved. All material within this
document is protected under copyright. No part of this document shall be reproduced
for any purpose without the express written consent of Mayo Hardware.
Made in China exclusively for Mayo Hardware PTY LTD
4 Secombe Place, Moorebank NSW 2170 Australia
Customer Service: 1300 360 211 Web: decoreheating.com.au
Ref: 1FPT_DFGFT_IM_vs1