Dedicated Micros DM18X User manual

SPEED DOME CAMERA
Please read this manual thoroughly before use and keep ithandy for future reference.
Rev.070514
Instruction Manual
DM/CAM/SD18X/A
DM/CAM/SD22X/A
DM/CAM/SD26X/A
Model No. :

II
Warnings and Cautions
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instruction in the literature
WARNIN
G
CAUTION
accompanying the product.

III
FCC COMPLIANCE STATEMENT
FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO
COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO
PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE
REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN
THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY
ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE
INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL
AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE
USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN
EXPENSE.
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY
THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME À LA NORME
NMB-003 DU CANADA.
CE COMPLIANCE STATEMENT
WARNING
THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS
PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER
MAY BE REQUIRED TO TAKE ADEQUATE MEASURES.

IV
IMPORTANT SAFEGUARDS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that product heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong is provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
14. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED
SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO
NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE
OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
15. Use Certified/Listed Class 2 power supply transformer only.

V
Table of Contents
Chapter 1 — Introduction............................................................................................................. 1
1.1 Features...............................................................................................................................................1
Chapter 2 — Installation and Configuration .............................................................................. 2
2.1 Package Contents................................................................................................................................2
2.2 Connector board of Dome Camera......................................................................................................3
2.3 Setting Dome Camera Termination......................................................................................................4
2.4 Setting Dome Camera Address (ID) ....................................................................................................5
2.5 Setting Dome Camera Protocol...........................................................................................................6
2.6 Connections.........................................................................................................................................7
Connecting to the RS-485/ 422............................................................................................................7
Connecting Video out connector ..........................................................................................................7
Connecting Alarms ...............................................................................................................................7
Connecting the Power ..........................................................................................................................7
2.7 Getting Started.....................................................................................................................................8
Chapter 3 — Program and Operation ......................................................................................... 8
3.1 Dome Camera Selection......................................................................................................................8
3.2 Accessing On-Screen Menu Utility ......................................................................................................9
3.3 Auto Scan.............................................................................................................................................9
3.4 Preset.................................................................................................................................................11
3.5 Shortcut of Preset Program ...............................................................................................................12
3.6 Tour ...................................................................................................................................................13
3.7 Pattern ...............................................................................................................................................14
3.8 Alarm..................................................................................................................................................15
3.9 Area Title ............................................................................................................................................16
3.10 Privacy Zone....................................................................................................................................17
3.11 Camera – DM/CAM/SD18X/A , SD26X/A MODEL .........................................................................18
Focus Control .....................................................................................................................................18
WB (White Balance) Control ..............................................................................................................19
AE Control ..........................................................................................................................................19
Line Lock Control................................................................................................................................20
Night Shot Menu .................................................................................................................................20

V
I
3.12 Camera – DM/CAM/SD22X/A MODEL ...............................................................................................21
Focus Control .......................................................................................................................................21
WB (White Balance) Control ................................................................................................................22
AE Control ............................................................................................................................................22
Line Lock Control .................................................................................................................................23
3.13 Camera - DM/CAM/SD26X/A MODEL ..............................................................................................23
3.14 Dome Setup.........................................................................................................................................24
Language Setup...................................................................................................................................24
Home Function Setup...........................................................................................................................24
OSD Display.........................................................................................................................................25
View Direction ......................................................................................................................................25
Dome OSD Display ..............................................................................................................................25
Area Display .........................................................................................................................................25
View Angle Setup .................................................................................................................................26
Panning Range.....................................................................................................................................26
Flip........................................................................................................................................................26
Tilt Over Angle......................................................................................................................................26
Initialize Data........................................................................................................................................27
Origin Offset .........................................................................................................................................27
Dome Reset ........................................................................................................................................27
System Information ..............................................................................................................................27
Appendix A — Specifications ....................................................................................................28
Appendix B — Troubleshooting................................................................................................30
Appendix C — Glossary.............................................................................................................31
Appendix D — Bubble Ring ......................................................................................................33
Appendix E — Short Cut Key (Pelco protocol) by KBS3 keyboard ......................................34

1
Chapter 1 — Introduction
1.1 Features
•240 Preset positions.(1-32,35-59:by PELCO-P protocol)
•8 Tours consist of Preset, Pattern, Auto-Scan and other Tours can be programmed with over
300 functions and Preset location. While moving, each Preset scan can be watched in smooth
Vector Scan mode.
•8 Auto Scans including vector scan and 1 Endless Auto-Scan.
•4 Patterns (240second).
•8 Privacy zones.
•8 Alarm inputs / 4 Aux outs (NC & NO).
•Variable speed from 0.1°/sec to 90°/sec.
Pan / Tilt speed is inversely proportional to the zoom ratio.
Maximum speed is 380°/sec when preset command.
•Programmable user preferences (alarm, preset, title, etc.).
•Up to 999 selectable camera addresses..
•Built-in RS-485/422 receiver driver.
•Clear bubble with black liner (shelter) for concealing the camera.
•Optional Tinted Bubble, Indoor & Outdoor pendant housing with heater & blower, Indoor Flush
mount, Parapet mount & Roof Top mount.

2
Chapter 2 — Installation and Configuration
2.1 Package Contents
The package contains the following.
Dome Camera ………………………1
Bubble Ring ………………………1
Instruction Manual (This Document) ………………………1
Assembly Screws for Attaching a dome ………………………3
Plastic Anchor ………………………3
10Pin Connector ………………………1
12Pin Connector ………………………2
CAUTION: Be sure to have caution labels (Eversion only) on both the body and the base
of the camera. Different version will not support input and output.
The dome camera is for use in surface mounting applications and the mounting surface should
be capable of supporting loads up to 10lb (4.5kg).
The dome camera’s base should be attached to a structural object, such as hard wood, wall stud
or ceiling rafter that supports the weight of the dome camera.
Figure 1 – Installation
Unlock Lock
Lock BODY
BASE
A
lign extruded tap in the base to
the Keyhole on the pcb in the body
SURFACE(CEILING)
CABLE ENTRY

3
2.2 Connector board of Dome Camera
Figure 2 – CONNECTOR BOARD

4
The dome camera must be installed by qualified service personnel in accordance with all local
and federal electrical and building codes. The system should be installed according to Figures 2
through 6.
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
81
1
2
3
4
5
6
7
8
9
0
81
1
2
3
4
5
6
7
8
9
0
81
S1
S2
S3
ON KSD02H
12
9A
SW1
ononon
1 2 3 41 2 3 4
S4
S5
S6
Figure 3 – Layout of Switches
2.3 Setting Dome Camera Termination
The device which is connected at end of line, whether it is a dome camera or a keyboard
controller, must have the cable for communication terminated by setting the appropriate DIP
switch. Without proper termination, there is potential for control signal errors. Total length of the
cable for communication should not exceed 4,000ft (1.2km).
ON KSD02H
12
9A
SW
1
Figure 4 – Setting Dome Camera Termination
SW1 1 2
Terminated ON ON
Not terminated OFF OFF
Address(ID) and Protocol
selection Switches
Termination Switches

5
2.4 Setting Dome Camera Address (ID)
To prevent damage, each dome camera must have a unique address (ID). When installing
multiple dome cameras using a multiplexer, it is suggested that the dome camera address match
the multiplexer port number.
If you want to set the address more than 999, you should contact the service provider.
Example: Port 1 = Dome 1, Port 2 = Dome 2 … Port 16 = Dome 16. If more than 16 dome
cameras are installed using two or more multiplexers, ID of the dome camera should be ID of
MUX x No. of camera IN. (e.g. multiplexer ID= n, Camera IN= m then ID of Dome =16x(n-1)+m )
Refer to Figures 4-5 for setting the dome camera address (ID) and protocol selection.
Figure 5 – Setting Dome Camera Address (ID)
1
2
3
4
5
6
7
8
9
0
8
1
1
2
3
4
5
6
7
8
9
0
8
1
1
2
3
4
5
6
7
8
9
0
8
1
S3
S2
S1
DOME ID S3 S2 S1
1 0 0 1
2 0 0 2
. . . .
999 9 9 9

6
2.5 Setting Dome Camera Protocol
If a dome camera is to be installed with a Dedicated Micros KBS3 keyboard, select the switch as
the same as the Dedicated Micros DVR.
Consult service personnel if a dome camera is installed with device other than a keyboard
controller.
S/W On Off FUNCTION
D1 S4-1 Enable Disable Alarm
D2 S4-2 PAL NTSC NTSC/PAL
D3 S4-3 ENDLESS Pan mode
D4 S4-4 RS-422 RS-485 RS-422/RS-485
D5 D6 D7
S5-1 S5-2 S5-3 PROTOCOL
Off Off Off
F2,F2E,P,D,E & Ph Protocol
(Default)
Off Off On Reserved
Off On Off S 422
Off On On Reserved
On Off Off V Protocol
On Off On Reserved
On On Off D Color
On On On Reserved
D8 D9 D10
S5-4 S6-1 S6-2 BAUD RATE
Off Off Off 2400 bps
Off Off On 4800 bps
Off On Off 9600 bps (Default)
Off On On 19200 bps
On Off Off 38400 bps
On Off On 57600 bps
On On Off 115200 bps
On On On 230400 bps
D11 D12
S6-3 S6-4 CAMERA
Off Off Default cameras (Default)
Off On Reserved
On Off Reserved
On On Reserved
Dedicated Micros DVR
Defaults(9600bps) D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12
ON ON
OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF
Figure 6 – Protocol Selection Switches
Camera
Protocol
Alarm
1234
S6
S5
S4
Baud rate
NTSC/PAL
RS-485
12341234
RS-422/
D1D2D3D4D5D6D7D8D9
D12
D10
D11
NTSC PAL
on
on
S4 S4
Note: When you use the
Pelco-P protocol with 4800bps
in the DVR, you should
change the baud rate to 4800
b
p
s of the dome.

7
2.6 Connections
• Connecting to the RS485/ 422
The dome camera can be controlled remotely by an external device or control system, such as a
control keyboard, using RS485 half-duplex, RS422 duplex or simplex serial communications
signals. Connect Marked Rx+(Tx+), Rx-(Tx-) to Tx+ and Tx- of the RS485 control system.
If control system is RS422, connect Rx+(Tx+), Rx-(Tx-) and Rx+, Rx- of the dome camera to
Rx+, Rx- and Tx+, Tx- of the control device respectively.
• Connecting Video out connector
Connect the video out(BNC) connector to the monitor or video input.
• Connecting Alarms
AL1 to 8 (Alarm In)
You can use external devices to signal the dome camera to react on events. Mechanical or
electrical switches can be wired to the AL (Alarm In) and GND (Ground) connectors.. See
Chapter 3 — Program and Operation for configuring alarm input.
GND (Ground)
NOTE: All the connectors marked GND are common.
Connect the ground side of the Alarm input and/or alarm output to the GND connector.
NC(NO)1 TO 4 (Normal Close or Normal Open : Alarm Out)
The dome camera can activate external devices such as buzzers or lights. Connect the device to
the NC(NO) (Alarm Out) and COM (Common) connectors. See Chapter 3 — Program and
Operation for configuring alarm output.
• Connecting the Power
Connect the power of AC 24V 850mA to the dome camera.
Use certified / Listed Class 2 power supply transformer only.

8
2.7 Getting Started
Once installed apply power to the dome camera. The dome camera will start a configuration
sequence.
OSD Position
Chapter 3 — Program and Operation
3.1 Dome Camera Selection
The Dedicated Micros KBS3 keyboard is the recommended device for controlling the PTZ
camera. Before you program or operate a dome camera, you must select the dome camera by
pressing the camera number key.
Note: Install the dome with the same dome ID as the camera input number to camera
input port of the DVR. Refer to the manual of the DVR.
001 PRESET
EMPTY DATA !
T001 DOMEID:0001
ALARM:1 W→360.0,090.0
PRESET No.
INFORMATION
DISPLAY
FUNCTION
UNDER RUNNING
ALARM DISPLAY
CAMERA TITLE
CAMERA ID
VIEW DIRECTION
PAN & TILT ANGLE
PRESET TITLE
or AREA TITLE

9
3.2 Accessing the On-Screen Menu Utility
You can call up the On-screen menu utility on your monitor by pressing PRESET .
The DVR displays the following pop-up window:
Pressing 95 will display the following On-screen menu.
NOTE: Quick pressing buttons may not operate, press a button slowly.
NOTE: When you can’t enter the menu, first press PRESET + 96 and PRESET + 95 again.
NOTE: The operation below is explained based on the KBS3 keyboard
3.3 Auto Scan
The Auto scan supports up to 8 programmed angles at user-programmable speeds. Follow
these steps to program Auto Scan:
Goto preset
Enter PRESET number
DOME MENU
AUTO SCAN
PRESET
TOUR
PATTERN
ALARM
AREA TITLE
PRIVACY ZONE
CAMERA
DOME SETUP
EXIT(ESC TO EXIT)
AUTO SCAN SETUP
SCAN 01 : AUTOSCAN01
SPEED(MODE) : FAST VECTOR
START ANGLE : 127.1, 027.7 X7
END ANGLE : 157.7, 080.7 X13
SCAN DIR. : CCW
SWAP : OFF
SAVE AND EXIT (ESC TO CANCEL)
HOLD DOWN CTRL KEY
WHILE SELECT POSITION.

10
SPEED(MODE) : NORMAL1~NOMAL9,SLOW VECTOR,FAST VECTOR
NORMAL1 (SLOWER) ↔NORMAL9 ( FASTER)
SLOW VECTOR, FAST VECTOR : Move from start point to end point
including tilt and zoom simultaneously and linearly. In case of 22x model,
zoom is fixed at more wide angle and the zoom magnification information
is not displayed.
1. Press PRESET + 60 key to enter Auto Scan menu directly. Or press PRESET + 95 keys to
display the main menu on the monitor. Scroll to Auto Scan and push the Joystick to the right.
2. Select an Auto Scan number by pushing the Joystick left or right.
3. Twist the Joystick to enter the title by scrolling through the alphanumeric characters and
pushing the handle to the right or left to move to the next space. Press PRESET + 94 keys
or push the Joystick down to finish title mode.
4. Push the Joystick downward to select “Speed” and set the speed by twisting the Joystick
clockwise or counterclockwise to select the auto scan speed.
5. When finish entering the title, select “START ANGLE” with the Joystick. Press PRESET +
95 keys, then select the start position and the zoom using the Joystick. Current position will
be displayed. Press PRESET + 95 keys to complete the selection of the start position.
6. Push the Joystick downward to select “END ANGLE.” Press PRESET + 95 keys, then move
the Joystick to select the end position and the zoom. The end position angle should be larger
than start position. Press PRESET + 95 key to complete the selection of the end position.
7. Select Save and Exit by pushing the Joystick to the right. Press PRESET + 96 keys to exit
the program without saving.
NOTE: Using the Tour mode in conjunction with preset and Auto Scan, you can make the camera
travel from one preset position to another preset position at a specific speed. (Pan only)
a. Before entering the Auto Scan menu, select a preset position as a starting point for Auto Scan.
Example:PRESET + 02 and do step 1 to 4. Instead of step 5, just press PRESET + 95 key
twice at the start angle position, the current position will be displayed as a start position.
b. Save and exit from the menu.
c. In normal mode, call a preset to be the end point of scan. Press PRESET + 03 then press
PRESET + 60 keys to enter the Auto Scan menu. Move the cursor position to END ANGLE.
Just press PRESET + 95 key twice at the end angle position. Do steps 7.
Example:Preset 001>002>003>004>005>006, Auto Scan 01 starts at 002, ends at 003,
Auto Scan 02 starts at 005, ends at 006. If you set Tour 01: 001, 002, A01, 004, A02.
1 Î2 2~3 Î4 Î5~6 Î1 Î2 2~3 ……
Where Î: Quick move, ~ : Programmed speed by Auto Scan.
Also you can execute Endless Auto Scan which is to turn one direction continuously by Pressing
PRESET + 99 or AUTOPAN.

11
3.4 Preset
If you need to view specific places routinely, you should program presets. A preset is a
programmed video scene with automatic pan, tilt, zoom, focus and iris settings. Once
programmed, pressing a PRESET button and entering the number on your keyboard
automatically calls up the preset. In addition, presets may be assigned to alarm actions or as the
“home” position for the dome camera.
There are three pages of preset menu, each page can hold 80 presets. Pages can be scrolled
by pushing the Joystick to the Left or Right on the first or last No. of Preset.
NOTE: In case of the KBS3 keyboard, you can call the preset 1-32, 35-59.
NOTE: When you call the preset number under 10, you should press 0 first. (1: press 0 + 1)
x : 16 digits of title for preset label
= : blank preset position
* : position has the preset
█: Current cursor position
Follow steps below to store the Preset positions:
1. Press PRESET + 95 to display the main menu. Select the Preset option by using the
Joystick to the right. (Press PRESET + 93 to go directly to the Preset menu without going
through the main menu.)
2. Select the blank preset position to be stored by pushing the Joystick up, down, right, or left.
3. The position, which is marked with *, already has the preset view assigned. To review the
stored preset, press PRESET + 93 key on the *，The camera will show the stored preset
view.
4. After selecting a blank position, press PRESET + 95, Use the Joystick to control the
direction of the camera and lens.
PRESET SETUP
NO. 001: xxxxxxxxxxxxxxxx
FOCUS : AUTO (MANUAL)
IRIS : AUTO (MANUAL)
DWELL : 03 SEC(3~99)
1234567890 1234567890
00█***======01==========
02==========03==========
04==========05==========
06==========07==========
JOY-LEFT TO PREV. PAGE
SAVE AND EXIT(ESC TO CANCEL)

12
5. After aiming the camera (view direction and lens control), press PRESET + 95 again.
6. Then twist the Joystick handle or press ZOOM IN or ZOOM OUT Key to store the selected
view. The position number will be displayed and the user will be prompted to enter a preset
title.
7. Enter the title for the preset position using the Joystick. (Rotate handle clockwise and
counterclockwise or press ZOOM IN or ZOOM OUT Key to scroll through the alphanumeric
characters, push the handle to right or left to select next or previous digit.)
8. When you are finished entering the title, push the Joystick downward. Set the focus by
pushing the Joystick to the right or left. Set the IRIS value in the same manner as the focus.
9. Move to the DWELL setting by pushing the Joystick down. Twist the Joystick clockwise or
counterclockwise to increase or decrease dwell time of the preset position.
10. Push the Joystick downward then the blank preset position changes *.
11. Repeat steps 2 through 10 for each additional preset position.
To select the next page of presets, scroll the page by pushing the Joystick to the Left on the
first and last columns of the menu. (In using the KBS3 keyboard with the PELCO-P protocol, you
can call the preset 1-32, 35-59.)
12. To edit the title of a stored preset, use the Joystick to position the cursor on the desired
preset position (*). Press the PRESET + 93key to recall the stored preset. Twist the zoom
handle clockwise to enter the preset title field. Preset titles are useful with short cut preset
programming.
13. Select Save and Exit by pushing the Joystick to the right. Press PRESET + 96 to exit the
Preset menu without saving.
NOTE: Press PRESET + 91 at programmed position to delete a programmed preset view.
NOTE: In the normal display mode, an alternate method is to press the PRESET button two times
quickly in the DS2 model.
3.5 Shortcut of Preset Program
After selecting a view to be stored (direction of the camera, zoom and focus), press and hold
PRESET until the pop-up window below displays in DS2 model.
Press number you want up to 99.The old saved preset number is overwritten.
NOTE: Camera 10 is number 0 and you should press 0 and 1 to enter 1.
NOTE: In case of the KBS3 keyboard, you can call the preset 1-32, 35-59 and the other preset
numbers can be used in the tour, the alarm and the home function.
Save preset
Enter PRESET number
1-99

13
3.6 Tour
There are 8 programmable Tours. Each Tour consists of up to 42 Preset positions, Patterns,
Scans or other Tours (second-level). Using second-level Tours, it can be expanded to over 300
functions in a single Tour. However second level Tours will be ignored when called by a Tours.
The following example illustrates this concept:
If Tour1 has Preset1ÎPreset2ÎTour2ÎTour3 and
Tour2 has Preset3ÎPreset4 ÎPreset5 ÎTour4and
Tour3 has Preset6ÎPattern 1and
Tour4 has Preset7.
Tour1 executes as follows:
Preset1 ÎPreset2 ÎPreset3 ÎPreset4 ÎPreset5 ÎPreset6 ÎPattern1 Î
Preset1 Î... (Repeat)
Tour2 executes as follows:
Preset3 ÎPreset4 ÎPreset5 ÎPreset7 ÎPreset3 … Repeat
(Tour4 is still valid if called directly from Tour2.)
xxxxx : 16 digits of title for tour label
=== : blank preset position
SCAN TYPE : Max (Normal)/ Slow V. Scan/ Fast V. Scan
DWELL : 03-99 Sec
003 : Preset 003 (1~240)
A08 : Auto Scan 08 (1~8)
P01 : Pattern 01 (1~4)
T02 : Tour 02 (1~8)
Follow the steps below to program the Tours:
1. Press PRESET + 95 to display the main menu on the monitor. Scroll to Tour and push the
Joystick to the right to enter the Tour menu. Or just press the Tour key on the keyboard
2. Choose an empty location to be programmed by pushing the Joystick up, down, right, or
left.
3. To see a stored preset view, use the Joystick to move the cursor to a stored position. By
pressing PRESET + 93 keys, the camera will move to the stored Preset view.
TOUR 01:xxxxxxxxxxxxxxxx
SCAN TYPE:NORMAL
=== === 003 === === === ===
A08 === === === === === ===
=== T02 === 001 === === ===
=== === === T08 === === ===
=== === === === === === ===
=== === === === === === ===
SAVE AND EXIT(ESC TO CANCEL)
PRESS FUNCTION KEY AND ROTATE
JOYSTICK TO SELECT NUMBER.

14
4. To add a stored preset as a Tour, twist the Zoom handle or press Zoom Key (Programmed
preset will scroll). To remove a stored preset from the Tour, press PRESET + 91 keys,
blank position mark (===) will be displayed. You can overwrite the programmed position.
5. To place functions other than preset, press Tour(PRESET + 70), Pattern(PRESET + 80),
or Scan(PRESET + 60 ) for Tour, Pattern or Auto Scan respectively.
6. Repeat Step 2 through 5 for each desired position. Each title will be displayed on top of the
line.
7. Up to 36 Presets, Tours, Patterns Scans can be selected for a Tour. You can expand the
Tour sequence by calling other programmed tours. Push the Joystick handle to right or left
while the cursor is on the top of the line (TOUR 01) to select another page of the Tour menu.
(TOUR 01)
8. You can enter a title for the selected Tour by twisting the Joystick while the cursor is on
the top of the line (TOUR 01). Rotate the handle clockwise or counterclockwise to scroll
through the alphanumeric characters. Push the handle to the right or left to select the next
or previous digit.
9. Select Save and Exit by pushing the Joystick to the right. Press PRESET + 96 to exit the
program without saving.
NOTE: Press PRESET + 91 key at a programmed position to delete programmed function.
In the Tour mode, in conjunction with preset and Auto Scan, you can make the camera
travel from a preset position to another preset position at a specific speed.
Example: Preset 001>002>003>004>005>006, Auto Scan 01 starts at preset 002, ends at
preset 003, Auto Scan 02 starts at preset 005, ends at preset 006; Tour01: 001, 002, A01, 004,
A02.
1 Î2 2~3 Î4 Î5~6, repeat
where Î: Quick move, ~ : Programmed speed
3.7 Pattern
The Pattern feature records user control of the selected dome camera for up to 240 seconds. Up
to four 4 patterns can be stored and played back by pressing PRESET + 81 ~ 84 keys
subsequently. Alternatively, the PATROL + 3 digits (001-004) can also be pressed on the
keyboard of the DS2 model.
Follow steps below to program the Pattern:
PATTERN SETUP
NO. TITLE SEC
01 : xxxxxxxxxxxxxxxx 000
02 : xxxxxxxxxxxxxxxx 041
03 : xxxxxxxxxxxxxxxx 010
04 : xxxxxxxxxxxxxxxx 020
TOTAL 071
SAVE AND EXIT(ESC TO CANCEL)
HOLD DOWN CTRL KEY
WHILE RECORDING.