DEEP SEA ELECTRONICS DSE335 User manual

DEEP SEA ELECTRONICS
DSE335 INSTALLATION NSTRUCTIONS
053-136
ISSUE 3
ACCESSING THE FRONT PANEL EDITOR (FPE)
• Press and hold the (stop) and the (tick) button.
• I a module security PIN has been set, the PIN number request is shown.
• Press (tick). The irst ‘#’ changes to ‘0’. Press (up) or (down)
to adjust it to the correct value.
• Press (right) when the irst digit is correctly entered. The digit you
have just entered shows ‘#’ or security.
• Enter the remaining digits o the PIN number. Press (le t) to move
back to adjust one o the previous digits.
• Press (tick) a ter entering the inal PIN digit. The PIN is checked or
validity. I the number is not correct, you must re-enter the PIN.
•
I the PIN has been success ully entered (or the module PIN has not been
enabled), the editor is displayed.
EDITING A PARAMETER
• Press the Press the (le t) or (right) buttons to cycle to the section
you wish to view/change.
• Press the (up) or (down) buttons to select the next parameter or
previous parameter within the current page.
• When viewing the parameter to be changed, press the (tick) button.
The value begins to lash.
• When editing the scheduler, press the (le t) or (right) button to
move between the various parameters o the scheduler.
• Press the (up) or (down) buttons to adjust the value to the required
setting.
• Press the (tick) button to the save the current value, the value ceases
lashing.
• Press and hold the (tick) button to save all changes and exit the editor.
• Alternatively, press and hold the (stop) button to cancel all changes
and exit the editor.
TYPICAL WIRING DIAGRAM

FRONT PANEL CONFIGURATION EDITOR
Page
Parameter
Va ues
DISPLAY
LCD Contrast 0%
Language English
LCD Page Timer hh:mm:ss
Scroll Delay hh:mm:ss
Date and Time dd-mm-yyyy, hh:mm:ss
S1
S1 Option Generator, Mains
Immediate S1 Dropout Inactive, Active
Under Voltage Trip 0 V
Over Voltage Trip 0 V
Under Frequency Trip 0 Hz
Over Frequency Trip 0 Hz
S2
S2 Option Generator, Mains
Immediate S2 Dropout Inactive, Active
Under Voltage Trip (Generator Option) 0 V
Over Voltage Trip (Generator Option) 0 V
Under Frequency Trip
(Generator Option) 0.0 Hz
Over Frequency Trip (Generator Option) 0.0 Hz
Under Voltage Trip (Mains Option) 0 V
Over Voltage Trip (Mains Option) 0 V
Under Frequency Trip (Mains Option) 0.0 Hz
Over Frequency Trip (Mains Option) 0.0 Hz
TIMERS
S1 Transient Delay mm:ss
S2 Start Delay hh:mm:ss
S2 Warming Up Time hh:mm:ss
S2 Fail Delay mm:ss
Elevator Delay mm:ss
Non-sync Trans er Time mm:ss.s
Check-Sync Trans er time mm:ss.s
S2 Return Delay hh:mm:ss
S2 Cooling Time hh:mm:ss
S2 Fail to Stop Enable Inactive, Active
S2 Fail to Stop Delay mm:ss
S2 Transient Delay s.s
SCHEDULER
Scheduler Enable Inactive, Active
Bank 1 Period Weekly, Monthly
Bank 2 Period Weekly, Monthly
Bank 1 Events Con iguration See Overlea
Bank 2 Events Con iguration See Overlea
SCHEDULER EVENT CONFIGURATION
Bank 1 and Bank 2 have eight (8) events each with con iguration options as shown
below:
Page
Parameter
Va ues
SCHEDULER
(Event Con iguration)
Event Run Mode Do Not Trans er
Trans er to S1
Trans er to S2
S1 O Load (When S1 = Gen)
S2 O Load (When S2 = Gen)
Event Week 1-4
Event Start Time hh:mm
Event Duration hh:mm
Event Day Monday to Sunday
DIMENSIONS AND MOUNTING
For lat sur ace mounting in a type 1 enclosure and use in a pollution degree 2
environment .
DIMENSIONS
240 mm x 181 mm x 41 mm
(9.4” x 7.1” x 1.6”)
PANEL CUTOUT
220 mm x 160 mm
(8.7” x 6.3”)
WEIGHT
680 g
(0.68 kg)
Deep Sea E ectronics P c.
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.deepseaplc.com
Deep Sea E ectronics inc.
Phone: [phone]
Fax: [phone]
TOLL FREE (USA only)
Tel: [phone]
Email: [e-mail]
Web:
www.deepseausa.com