Defender Ip2kcb1 User manual

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

QUICK START GUIDE

2K (4MP) Wireless IP Camera

IP2KCB1

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

THANK YOU FOR JOINING THE DEFENDER FAMILY

Help Us Make the Best Security Solutions Possible!

Leave an Honest Review in the First 6 Months and Receive

a FREE 1 Year Extended Warranty.

www.defender-usa.com/IP2KReview

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

WHAT’S INCLUDED

WHAT YOU’LL NEED FOR SET UP & INSTALLATION

• Drill

• Phillips (#2) Screwdriver

• Ladder (if required)

• Ethernet Cable (for rst time setup only depending on your Network setup)

NOTE: The IP 2K Camera will only work on 2.4 GHz frequency and is not

compatible with 5 GHz networks.

Camera with pre-installed

16GB SD Card

Mounting Hardware

Wi-Fi Camera Antenna

Ethernet Cable Shield

Camera Power Supply (10ft)*

*Extension Power Cable

may be required.

Camera Reset

Button

SD Card

Input

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

2. Power on the camera by

connecting the camera cable

to the adapter.

GETTING STARTED

1. Remove the red protection cap

and connect the antenna to

the camera.

3. Download the SmartSignal

mobile app. Open the app on

your device.

4. Setting up your account requires

access to your email to receive

the Verication code and is

valid for 15 minutes.

NOTE: Minimize your keyboard

to continue.

[email protected]

IMPORTANT: Depending on your Network setup, you may need to connect

the camera to your modem/router using an Ethernet cable (not included) the

rst time you add the camera to the app.

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

5. Once your account is activat-

ed, the Add Device screen will

open. Tap the +icon to add the

camera.

7. Enter your Wi-Fi Password and

click Next to continue.

IMPORTANT: Ensure your mobile device is connected to your Wi-Fi network

(2.4 GHz)– the camera and mobile device must be connected to the same

network for setup.

6. Scan the QR Code and select

Single Camera Setup. If your

network allows, the camera will

connect over Wi-Fi directly.

8. Wait for 120 seconds for camera

to pair. NOTE: If the camera does

not connect, follow the Setup Using

Ethernet Cable.

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

SETUP USING ETHERNET CABLE (NOT INCLUDED)

4. Tap Device connected to

network link to continue.

NOTE: DO NOT tap Next.

3. Exit the setup screen by clicking

X. Scan the QR code and select

Single Camera Setup.

1. Error message of Cong failed

will appear if Wi-Fi pairing fails.

Try setup using Ethernet Cable.

2. Connect the camera to your

modem/router using an

Ethernet Cable.

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

7. Enter your Wi-Fi Password and

tap the Save icon (top of the

screen) to continue.

5. Create an Admin Password

for your Device (Camera) and

Tap OK to continue.

6. Tap to select your Wi-Fi Network

from the list. NOTE: Camera will

only work on 2.4 GHz frequency.

8. Once the camera is connected

you will see the Add successfully

screen. Tap Start Preview to

open the app.

NOTE: If you used a hard wire connection to get started, once the camera

has been connected to the app, you can disconnect the Ethernet cable and

use your Wi-Fi connection.

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

APP FUNCTIONALITY

Camera Name

Alerts Received

Device Selection

Tap for Live View

Account Information

and Settings

Motion Detection

• ON (Yellow)

• OFF (Grey)

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

MOTION ALERT

1. Tap on the camera to enter

Live View.

3. Tap to select Alarm.

2. Tap on the Setting icon to

enter to the device settings.

4. Slide the switch to turn Motion

Detect on/o.

For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT For the full product manual and support videos visit www.DEFENDER-USA.COM/IP2KSUPPORT

ACTIVITY ZONE - MOTION ALERT

RECORDING SCHEDULE

1. In Settings, tap to select the

Activity zones.

1. In Settings, tap to select the

General Record Schedule.

2. Tap and drag on the grid area.

Zones highlighted in red will

detect motion.

2. Tap the Day to create a schedule

and save.