Delfi DelfiScan C65 User manual

Quick Reference Guide
DelfiScan C65
General Purpose Corded
Handheld Linear Imager Bar Code Reader

Delfi Technologies A/S
Galoche Alle 1
4600 Køge
Denmark
Telephone: [phone]
An Unpublished Work - All rights reserved. No part of the contents of this
documentation or the procedures described therein may be reproduced or
transmitted in any form or by any means without prior written per-mission of
Delfi Technologies A/S. Owners of Delfi products are hereby granted a non-
exclusive, revocable license to reproduce and transmit this documentation for the
purchaser's own internal business purposes. Purchaser shall not remove or alter
any proprietary notices, including copyright notices, contained in this
documentation and shall ensure that all notices appear on any reproductions of
the documentation.
Electronic versions may either be downloadable from the Delfi website
(www.delfi.com) or provided on appropriate media.
Disclaimer
Delfi has taken reasonable measures to provide information in this manual that
is complete and accurate, however, Delfi reserves the right to
change any specification at any time without prior notice.
Patents
This product may be covered by one or more of the following patents:
Design Patents: CN ZL201230049587.7; EP1987843; USD677258.
Utility Patents: EP0789315B1; EP1128315B1; EP1396811B1; EP1413971B1; US5481098; US5992740;
US6098883; US6454168; US6561427; US6758403; US6808114; US6997385; US7387246; US7506816.
Additional patents pending

Quick Reference Guide 1
Delfi Technologies A/S
DelfiScan PRODUCT SERIES END USER LICENSE AGREEMENT
Notice to End User: The Delfi Product you have acquired contains embedded Software,
which is integral to the product's operation. This Software is being provided to you under
license, subject to the terms and conditions of this Agreement. If you use the Delfi Product,
you will be deemed to have accepted the terms and conditions of this Agreement. If you do
not intend to be bound to the terms of this Agreement, Delfi is not willing to license the
Software to you, you may not use the Delfi Product or the Software, and you must contact
the party from whom you acquired the Delfi Product for instructions.
This End User Software License Agreement ("Agreement") is a legally binding agreement
governing the licensing of the Software and Documentation byDelfi Technologies A/S and its
Affiliates ("Delfi") to the entity or person who has purchased or otherwise acquired a Delfi Product
("End User"). For purposes of this Agreement, any software that is associated with a separate end-
user license agreement is licensed to you under the terms of that license agreement. Delfi and
End User hereby agree as follows:
1.Definitions.
1.1 "Affiliate" means a business entity currently existing or later acquired that controls, iscontrolled
by, or is under common control with Delfi Technologies.
1.2 "Documentation" means materials such as user's guides, program reference guides, quick refer-
ence guides, manuals, orsimilar materials associated with orrelated to the Delfi Product,
whether in printed, "online", or other form.
1.3 "Proprietary Information" means: (a) source code, object code, software, documentation, and any
related internal design, system design, data base design, algorithms, technology, technical data
or information, implementation techniques, andtrade secrets related to the Software, (b) any
other trade secrets marked appropriately or identified as proprietary or confidential, and (c)
any information that End User, under the circumstances, should recognize as confidential.
Propri-etary Information does not include any informationthat the receiving party can establish
was (1) in the public domain, (2) already in the receiving party's possession orrightfully
known prior to receipt, (3) rightfully learned from a third party not in violation of any other's
proprietary rights, or (4) independently developed without access to Proprietary Information.
1.4 "Delfi Product" means the Delfi DelfiScan series scanner product, including all
embedded Software inand allDocumentation relatedto such product, which has been pur-
chased or otherwise acquired byEndUser, whether obtained directly orindirectly from Delfi
1.5 "Software" meansany software or computer programs of Delfi or its third party licensors in
machine readable form which is embedded in the Delfi Product, whether obtained directly or
indirectly from Delfi, including any replacement, update, upgrade, enhancement or mod-
ification.
2.Scope Of License Granted.
2.1 Delfi grants toEnd User a non-exclusive, non-transferable, perpetual license to use the Soft-
ware, solely onthe Delfi Product in which it is embedded ("designated Delfi Product"), in
machinereadable form only, solely for End User's internal business purposes. This Agreement
does not convey ownership ofthe Software to EndUser. Title to the Software shall be and
remain with Delfi or the third party from whom Delfi has obtained a licensed right. As used in
this Agreement, the term "purchase" or its equivalents when applied to the Software shall
mean "acquire under license." End User is not entitled to receiptor use of the source code to
anySoftware.
2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise repro-
duce or remanufacture the Software, whether modified or unmodified, norsell, assign, subli-
cense, distribute, lend, rent, give, or otherwise transfer the Software to any other person or
organization, for purposes other than as expressly provided in this Agreement, without
Delfi's prior written consent.
3.Transfers, Support.
3.1 Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer,
or other use of the Software on other than the designated Delfi Product will be a material
breach of this Agreement. However, Delfi may elect not to terminate this Agreement or the
granted licenses, but instead may elect to notify End User that End User is deemed to have
ordered and accepted a license for each breaching use. End User shall pay Delfi the applicable
list price for such licenses as ofthe date of such breach.
3.2 End User shall notsell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the
Delfi Product to anythird party unless such third party agrees with Delfi in writingto be
bound bythe terms andconditions of this Agreement. Any such transfer ofthe Delfi Product
absent such agreement shall be null and void.
3.3 End User may obtain support for Software from Delfi at Delfi's standard support fees and
under Delfi's standard support terms and conditions in effect at the time the support is
requested.
4.Intellectual Property.

2
End User acknowledges thatthe Software constitutes valuable trade secrets of Delfi or Delfi's third
party licensors and that theSoftware is protected by intellectual property laws and treaties. The
license set forth in this Agreement does not transfer to End User any ownership of Delfi's or its
third party licensors' copyrights, patents, trademarks, service marks, trade secrets, or other
intellectual property rights and End User shall have no right to commence any legal actions to
obtain such rights. End User shallnotremove, modify, or take any other action that would ob-
scure any copyright, trademark, patent marking, or other intellectual property notices contained in
or on the Delfi Product.
5.Proprietary Information.
5.1 End User acknowledges that Proprietary Information is the confidential, proprietary, and trade
secret property of Delfi and Delfi's thirdparty licensors and End User acquires no right or
interest in any Proprietary Information.
5.2 End User shall notdisclose, provide, or otherwise make available the Proprietary Information of
Delfi or its third party licensors to any person other than End User's authorized employees or
agents who are under confidentiality agreement, and End User shall not use the Proprietary
Information other than in conjunction with use of the Delfi Product exclusively for End User's
internal business purposes. End User shall take steps to protect the Proprietary Information no
less securely than if it were EndUser's own intellectual property.
5.3 The provisions ofthis Proprietary Information Sectionshall survive and continue for five(5)
years after the termination of this Agreement.
6.Limited Warranty.
6.1 Delfi warrants that, under normal use and operation, the Delfi Product will conform
substantially to the applicable Documentation for the period specified in the Documentation.
During this period, for all reproducible nonconformities for which Delfi has been given written
notice, Delfi will use commercially reasonable efforts to remedy nonconformities verified by
Delfi. End User agrees to supply Delfi with all reasonably requested information andassistance
necessary to help Delfi in remedying such nonconformities. For all defects reported to Delfi
within the warranty period, Delfi's liability is limited to providing End User with one copy of
corrections or responding toEnd User's problem reports according to Datalogic's standard
assistance practices. Delfi does not warrant that the product will meet End User's requirements
or that use of the product will be uninterrupted or error free, or that Delfi's remedial efforts will
correct any nonconformance. This limited warranty does not cover any product that have been
subjected todamage or abuse, whether intentionally, accidentally, or by neglect, or to
unauthorized repair or unauthorized installation, and shall be void if End User modifies the
product, uses the product in any manner other than as established in the Documentation, or if
End User breaches any of the provisions of this Agreement.
6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DELFI PRODUCT IS PROVIDED
"AS IS" AND DELFI MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED,
WRITTEN OR ORAL, WITH RESPECT TO THE PRODUCT, AND SPECIFI-CALLY
DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
7.Infringement.
7.1 Delfi will defend End User against any claim in a lawsuit that the Delfi Product furnished
hereunder infringe a United States patent or copyright of a third party and Delfi will pay any
damages finally awarded against End User by a court of competent jurisdiction that are
attributable to such claim or will pay End User's part of any settlement that is attributable to such
claim, provided, that 1) End User notifies Delfi promptly in writingofthe claim, 2)Delfi
controls the defense or settlement of the claim, and3)End User cooperates fully with Delfi in
such defense or settlement. All notices of a claim should besent toDelfi Technologies A/S,
Galoche Alle 1, 4600 Køge, Denmark.
7.2 In the defense or settlement ofanysuch claim, Delfi may, at its option, 1)procure for End
User the right to continue using the Delfi Product, 2) modify the Delfi Product so that it
becomes non-infringing, 3) replace the Delfi Product with an equivalent product not subject to
such claim, or 4) provide End User an opportunity to return the Delfi Product and receive a
refund of the purchase price paid, less a reasonable allowance for use.
7.3 Delfi shall have noliability to End User for claims ofinfringement based upon 1)the use of
any Delfi Product in combination with anyproduct which Delfi has not either furnished or
authorized for use with such Delfi Product 2) the use of any Delfi Product designed,
manufactured, or modified to the specifications of End User, or 3) End User's modification of
the Delfi Product without written authorization from Delfi.
DelfiScan C65

Quick Reference Guide 3
7.4 THE FOREGOING STATES DELFI'S COMPLETE AND ENTIRE OBLIGATION
CONCERNING CLAIMS OF PATENT, COPYRIGHT, OR OTHER INTELLECTUAL
PROP-ERTY INFRINGEMENT, CANCELS AND SUPERCEDES ANY PRIOR
AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES
CONCERNING SUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY
ANY PAST, CONTEMPO-RANEOUS, OR FUTURE AGREEMENTS OR DEALINGS
BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH
IN A FUTURE WRITING SIGNED BY BOTHPARTIES.
8.Limitation Of Liability.
EXCEPT AS PROVIDED IN SECTION 7, DELFI SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END
USER BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY,
WHETHER BASED UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY,
STRICT LIABILITY, WARRANTY, OR ANY OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END
USER FOR THE DELFI PRODUCT. UNDER NO CIRCUMSTANCES SHALL DELFI BE LIABLE TO
END USER OR ANY THIRD PARTY FOR LOST PROFITS, LOST DATA, INTERRUPTION OF BUSINESS OR
SERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL,
PUNITIVE, EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF DELFI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
9.Government Restricted Rights; International Use.
9.1 Use, duplication, or disclosure of the Software by the U.S. Government issubject tothe restric-
tions for computer software developed at private expense as set forth in the U.S. Federal
Acqui-sition Regulations at FAR 52.227-14(g), or 52.227-19 orin the Rights in Technical Data
and Computer Software clause at DFARS 252.227-7013(c)(1)(ii), whichever isapplicable.
9.2 If End User isusing the Delfi Product outside of the United States, End User must comply
with the applicable local laws of the country in which the Delfi Product is used, with U.S.
export control laws, and with the English language version of this Agreement. The provisions of
the "United Nations Convention on International Sale of Goods" shall not apply to this Agree-
ment.
10.Termination.
10.1 Either party may terminate this Agreement or any license granted under this Agreement at any
time upon written notice if the other party breaches any provision ofthis Agreement.
10.2 Upon termination of this Agreement, End User immediately shall cease using any nonembedded
software and shall return toDelfi or destroy allnon-embedded software covered by this
Agreement, and shall furnish Delfi with a certificate of compliance with this provision signed
by an officer or authorized representative of End User. For embedded software, End User
agrees to sign a waiver prepared by Delfi concerning further use of the embedded Software.
End User's resumed or continued use of the embedded Software after termination shall consti-
tute End User's agreement to bebound bythe terms and conditions of this Agreement for such
use.
11.General Provisions.
11.1 Entire Agreement; Amendment. This document contains the entire agreement between the par-
ties relating to the licensing ofthe Software andsupersedes all prior or contemporaneous
agree-ments, written or oral, between the parties concerning the licensing ofthe Software. This
Agreement may not be changed, amended, or modified except by written document signed by
Delfi.
11.2 Notice. All notices required orauthorized under this Agreement shall be given in writing, and
shall be effective when received, with evidence of receipt. Notices to Delfi shall be sent to the
attention of Contract Administration, Delfi Technologies A/S, Galoche Alle 1, 4600 Køge,
Denmark.
11.3 Waiver. A party's failure to enforce any ofthe terms and conditions of this Agreement shall not
prevent the party's later enforcement of such terms and conditions.
11.4 Governing Law; Venue: This Agreement and the rights of the parties hereunder shall be gov-
erned by and construed in accordance with the laws ofthe State of Oregon U.S.A, without
regard to the rules governing conflicts of law.The state or federal courts of the State of
Oregon located in either Multnomah orLanecounties shall have exclusive jurisdiction over all
matters regarding this Agreement, except that Delfi shall have the right, at its absolute
discretion, to initiate proceedings in the courts of any other state, country, or territory in which
End Userresides, or in which any of End User's assets are located.
11.5 Attorneys' Fees. In the event an action is brought to enforce the terms and conditions ofthis
Agreement, the prevailing party shall be entitled to reasonable attorneys' fees, both at trial
and on appeal.
- END -

4
Software Product Policy
Delfi reserves the right to ship its products with the latest
version of software/firmware available. This provides our cus-
tomers with the very latest in Delfi software technology. The
only exception to this policy is when the buyer has a signed
contract with Delfi that clearly defines the terms and con-
ditions for making software/firmware changes in products
shipped to the buyer.
Customers Under Software Support
Customers that elect to subscribe to Delfi Software Main-
tenance and Support Agreement will receive 30 days advance
notification of: (1) the release of a new software version; and/
or (2) discontinuation of any prior software version that will
no longer be supported. Delfi will provide maintenance for a
fee that will assist customers in transitioning to the next soft-
ware version. If a customer is currently using
the software version being discontinued, the
customer may elect to transition to any one of
the newer versions, depending on the hardware
in use.
To arrange for a Software Maintenance and
Support Agreement please contact your Delfi
sales person.
Hands Free Stand/Holder
An accessory is available which holds the reader at a
convenient angle, allowing hands free scanning of items. It can
also be used as a holder. Always press in on the release buttons
on both sides of the stand to raise the arm of the stand as
shown in the inset of Figure 1, otherwise you could damage
the locking mecha-nism. The holder “cup” can be positioned
in any of the three angles shown in the figure.
Refer to Scanning Modes on page 13 for information about pro-
gramming the reader for use with the stand.
Optional Wall
Mount Holder
DelfiScan C65

Hands Free Stand/Holder
Quick Reference Guide 5
Figure 1. Adjusting the Stand

6
Connect/Disconnect Cable
Connect Host Interface
Keyboard Wedge Interface
RS-232 Interface
USB Interface
1
2
K
e
y
b
o
a
r
d
R
S
-
2
3
2
U
S
B
DelfiScan C65

Aim and Scan
Quick Reference Guide 7
Aim andScan
3
012345 012345
65°
65°

8
Parts of the Reader
1.LED 3.Scan Window
2.Cable Release Hole 4.Trigger
1
23
4
DelfiScan C65

Programming Bar Codes
Quick Reference Guide 9
Programming Bar Codes
For your convenience, this guide includes the programming bar
codes required to configure the reader for use with different
in-terface (terminal/host) types.
See the Product Reference Guide (PRG) for more complete
in-formation about programming and configurable features.
You can download the latest version of the PRG and any other
avail-able publications for the reader from the website listed
on the back cover of this manual.
Resetting the Standard Product Defaults
If you aren’t sure what programming options are in your
reader, or you’ve changed some options and want the factory
settings restored, scan the Factory Default Settings bar code
below. This will copy the factory configuration for the
currently active in-terface to the current configuration.
Factory Default Settings
Host Interfaces
NOTE
Cables mayvary depending upon
sys-tem configuration.
Some interfaces require the reader to
start in the disabled state when pow-
ered on. If additional reader configura-
tion is desired while in this state, pull
the trigger and hold it for five seconds.
The reader will change to a state that
allows programming with bar codes.

10
RS-232 Interface
To use an RS-232 interface, scan the bar code for the
desired RS-232 host type.
Select RS-232 Standard
Select RS-232Wincor Nixdorf
Select RS-232 OPOS (foruse with OPOS/UPOS/JavaPOS)
DelfiScan C65

Programming Bar Codes
Quick Reference Guide 11
USB Interface
The reader attaches directly to a USB host, or a powered USB
hub, and is powered by it. No additional power supply is re-
quired. When using a USB interface, the reader auto-detects
the USB and defaults to the USB Keyboard interface.
Select USB-COM-STD1(simulates RS-232 standard interface)
Select USB Keyboard (with standard key encoding)
Select USB Alternate Keyboard (with alternate key encoding)
Select USB OEM
1. Download the correct USB Com driver from www.delfi.com.

12
Keyboard Wedge Interface
To use a Keyboard Wedge interface, scan the bar code for
the desired keyboard type.
Select KBD-AT
(AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95
w/Standard Key Encoding)
Select KBD-AT-NK
(IBM AT PS2 with standard key encoding but without
external kbd.)
Select KBD-AT-ALT
(AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95
w/Alternate Key)
Select KBD-AT-ALT-NK (for IBM AT PS2 with alternate
key encoding but without external keyboard)
Select KBD-XT (PC/XT w/Standard Key Encoding)
DelfiScan C65

Scanning Modes
Quick Reference Guide 13
Scanning Modes
The reader can operate in one of several scanning modes:
Trigger Single — When the trigger is pulled, scanning is activated
until one of the following occurs:
-a programmable duration1has elapsed
-a label has been read
-the trigger is released
This mode is associated with typical handheld reader operation:
when the trigger is pulled, scanning starts and the product
scans until the trigger is released, or a label is read, or the
maximum programmable duration1has elapsed.
Trigger Hold Multiple — When the trigger is pulled, scanning starts
and the product scans until the trigger is released or a
program-mable duration1has elapsed. Reading a label does
not disable scanning. Double ReadTimeout2prevents
undesired multiple reads while in this mode.
Trigger Pulse Multiple — When the trigger is pulled and released,
scanning is activated until programmable duration1has
elapsed or the trigger has been pulled again to transition to
another state. Double Read Timeout2prevents undesired
multiple reads while in this mode.
Flashing — The reader flashes3on and off regardless of the trigger
status.
Always On — No trigger pull is required to read a bar code. Scan-
ning is continually on. Double Read Timeout4prevents
unde-sired multiple reads while in this mode.
Autosense® Stand Mode — No trigger pull is required to read a bar
code. Scanning is turned on automatically when an item
is placed in reader’s field of view. If the trigger is pulled, the
reader acts as if it in Trigger Single mode. Double Read
Timeout4prevents undesired multiple reads while in this
mode.
Trigger Object Sense — This mode is similar to Autosense® Stand
NOTE
If the interface type is changed, scanner configu-
ration may be automatically reset to a different
Scanning Mode.
1. See the Product Reference Guide (PRG) for additional programmable
features, in this case: Scanning Active Time.
2. Double Read Timeout is also programmed using the PRG.
3. Controlled by Flash On Time and Flash Off Time. Use the PRG to pro-
gram these options.
4. Double Read Timeout is programmed using the PRG.

14
Mode, except that a trigger pull is required to activate the decoder.
Scan Mode = Trigger Single
Scan Mode = Trigger Hold Multiple
Scan Mode = Trigger Pulse Multiple
Scan Mode =Flashing
Scan Mode = Always On
Scan Mode = Autosense®Stand Mode
Scan Mode = Trigger Object Sense
DelfiScan C65

Troubleshooting
Quick Reference Guide 15
Troubleshooting
Problem Possible Cause Possible Solutions
Nothing happens when
the trigger is pulled.
No power to the
reader.
Check system power.
Ensure power supply
is connected.
Interface or power
cables are loose.
Ensure all cable connec-
tions are secure.
LED comes on, but bar
code does not decode.
Reader not pro-
grammed for correct
bar code type.
Ensure reader is pro-
grammed to read the
type of bar code
scanned. Refer to the
Product Reference
Guide (PRG) for more
informa-tion.
Bar code label is
unreadable.
Check the label to
ensure it is not defaced.
Try scanning another
bar code type.
Distance between
reader and bar code
is incorrect.
Move reader closer to or
further from the bar code.
Bar codereading abil-
ity has degraded.
Scan Window has
become dirty.
Clean window using a
soft, lint-free cloth
damp-ened with water.
Bar code isdecoded
but not transmitted to
the host.
Reader not pro-
grammed for the cor-
rect host type.
Scan the appropriate
host type bar code.
Refer to the Product
Refer-ence Guide (PRG)
for more information.
NOTE
For detailed troubleshooting, refer
to the Product Reference Guide.

16
LED and Beeper Indications
The reader’s beeper sounds and its LED illuminates to indicate
various functions or errors on the reader. A “Green Spot” also
lights to indicate a good read. The tables below list these indi-
cations. One exception to the behaviors listed in the tables is
that the reader’s functions are programmable, and may or may
not be turned on. For example, certain indications, such as the
power-up beep can be disabled using programming bar code
la-bels. Reference the PRG for a more detailed list.
Indication LED Beeper
Power-up
LED flashes/blinks on
power-up, however, this
may be too rapid to view.
With a USB interface, the
LED blinks until
enumera-tion with the
host is com-pleted.
Reader beeps four
times at highest
frequency and volume
upon power-up.
Good Read
LED behavior for this indi-
cation is configurable
using the PRG.
One beep atcurrent fre-
quency, volume,
mono/bi-tonal setting
and duration upon a suc-
cessful label scan.
ROM Failure 200ms on / 200ms off
Reader sounds one
error beep at highest
volume for 200 mS.
Limited Scan-
ning Label Read N/A
Reader 'chirps' six
times at the highest
frequency and current
volume.
Reader Disabled
The LED blinks continu-
ously 100mS on / 900 mS
off
N/A
DelfiScan C65

Ergonomic Recommendations
Quick Reference Guide 17
Ergonomic Recommendations
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Regulatory Information
All models are designed to be compliant with rules and regula-
tions in locations they are sold and will be labeled as required.
Any changes or modifications to equipment, not expressly ap-
proved by Delfi could void the user's authority to operate the
equipment.
Power Supply
Use only a power supply approved by Delfi for this product
and model. Models require either a Listed class II or class III
with a Limited Power Source(LPS) which supplies power di-
rectly to the reader. For the safety certification to be valid, class
III input power sources must be IEC/EN60950-1 (EN 60335-
series, EN 60065 or relevant) approved.
Input: 100 - 240 VACOutput: 5 VDC
Max Current: 0.35 AmpsPower Out: 12.5 Watts
CAUTION
In order to avoid or minimize the
potential risk of ergonomic injury fol-
low the recommendations below.
Consult with your local Health &
Safety Manager to ensure that you
are adhering to your company’s
safety programs to prevent
employee injury.
NOTE
For USB Power Off Terminal appli-
cations, attach to USB 1.0, 1.1 or
2.0 host device only.

18
Radio Frequency Interference Requirements
This equipment has been tested and found to
comply with the limits for a Class B digital de-
vice, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reason-able
protection against harmful interference in a residential in-stallation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accor-dance with the instruction
manual, may cause harmful interfer-ence to radio communications.
However there is no guarantee that interference will not occur in a
particular installation. If the equipment does cause harmful interference
to radio or televi-sion reception, which can be determined by turning
the equip-ment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver isconnected.
• Consult the dealer or an experienced radio/TV
technician for help.
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian IC-
ES-003.
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Reader Labeling
The label is shown here to illustrate its location only.
Please view the labels on your product for actual details.
CAUTION
The user is cautioned that
changes or modifications not
expressly approved by the party
responsible for compliance could
void the user’s authority to oper-
ate the equipment.
Tested to comply
with FCC Standards
FOR HOME OR OFFICE USE
DelfiScan C65