Deliberant APC 5M-18 V2 User manual

APC 5M-18 V2
Quick Installation Guide
Revision 1.2
21 October 2011
Copyright © 2011 Deliberant www.deliberant.com

deliberant Page 2
Copyright
© 2011 Deliberant
This user’s guide and the software described in it are copyrighted with all rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language in any form by any means without the written permission of Deliberant.
Notice
Deliberant reserves the right to change specifications without prior notice.
While the information in this manual has been compiled with great care, it may not be deemed an
assurance of product characteristics. Deliberant shall be liable only to the degree specified in the
terms of sale and delivery.
The reproduction and distribution of the documentation and software supplied with this product and
the use of its contents is subject to written authorization from Deliberant.
Trademarks
Deliberant logo is trademark of Deliberant LLC.
All other registered and unregistered trademarks in this document are the sole property of their
respective owners.

Quick Installation Guide Contents
deliberant Page 3
Contents
Copyright.............................................................................................................................................2
Notice ..................................................................................................................................................2
Trademarks.........................................................................................................................................2
CONTENTS ...........................................................................................................................................3
INTRODUCTION....................................................................................................................................4
FCC Warning.......................................................................................................................................4
FCC Caution....................................................................................................................................4
FCC Radiation Exposure Statement ...............................................................................................4
Antenna Installation .........................................................................................................................4
Antenna Compliance .......................................................................................................................4
CE Mark Warning................................................................................................................................5
R&TTE Compliance Statement...........................................................................................................5
Safety...............................................................................................................................................5
EU Countries Intended for Use........................................................................................................5
EU Countries Not Intended for Use.................................................................................................5
ABOUT THIS GUIDE.............................................................................................................................6
Prerequisite Skills and Knowledge......................................................................................................6
Definitions, Acronyms and Abbreviations............................................................................................6
Technical Support ...............................................................................................................................6
Contact Us...........................................................................................................................................6
INSTALLATION.....................................................................................................................................7
Package Contents...............................................................................................................................7
Hardware Introduction.........................................................................................................................8
LEDs................................................................................................................................................8
Assembling and mounting the APC 5M-18 V2....................................................................................9
ACCESS THE APC 5M-18 V2.............................................................................................................11
Connection via WEB Browser...........................................................................................................11
Resettingto Factory Defaults............................................................................................................12

Quick Installation Guide Introduction
deliberant Page 4
Introduction
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Caution
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
FCC Radiation Exposure Statement
To comply with FCC RF exposure requirements in section 1.1307, a minimum separation distance of
3.9 feet is required between the antenna and all occupational persons, and a minimum separation
distance of 8.7 feet is required between the antenna and all public persons.
Antenna Installation
WARNING: It is installer’s responsibility to ensure that when using the authorized antennas in the
United States (or where FCC rules apply), only those antennas certified with the product are used.
The use of any antenna other than those certified with the product is expressly forbidden in
accordance to FCC rules CFR47 part 15.204. The installer should configure the output power level of
antennas, according to country regulations and per antenna type. Professional installation is required
of equipment with connectors to ensure compliance with health and safety issues.
Antenna Compliance
The APC 5M-18 V2 radio module contains internal antenna.

Quick Installation Guide Introduction
deliberant Page 5
CE Mark Warning
This is a Class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
R&TTE Compliance Statement
This equipment complies with all the requirements of the Directive 1999/5/EC of the European
Parliament and the Council of 9 March 1999 on Radio Equipment and Telecommunication Terminal
Equipment and the Mutual Recognition of their Conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal
Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this manual and of the computer manufacturer
must therefore be allowed at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark,
Finland, France (with Frequency channel restrictions), Germany, Greece, Ireland, Italy, Luxembourg,
The Netherlands, Portugal, Spain, Sweden and United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states Iceland,
Liechtenstein, Norway and Switzerland.
EU Countries Not Intended for Use
None.

Quick Installation Guide About this Guide
deliberant Page 6
About this Guide
Prerequisite Skills and Knowledge
To use this document effectively, you should have a working knowledge of Local Area Networking
(LAN) concepts and wireless Internet access infrastructures.
Definitions, Acronyms and Abbreviations
The following typographic conventions and symbols are used throughout this document:
Additional information that may be helpful but which is not required.
Important information that should be observed.
bold
Menu commands, buttons, input fields, links, and configuration keys are displayed in bold
italic
References to sections inside the document are displayed in italic.
code
File names, directory names, form names, system-generated output, and user typed
entries are displayed in constant-width type
Technical Support
If you encounter problems when installing or using this product, please consult the Deliberant website
at www.deliberant.com for:
Direct contact to the Deliberant support centers.
Frequently Asked Questions (FAQ).
Download area for the latest software, user documentation and product updates.
Contact Us
EU office:
UAB WILIBOX
Veiveriu 150 - IIIa.
Kaunas, LT-46391
Lithuania
[email protected]
US office:
Deliberant
138 Mountain Brook Drive
Canton, GA 30115
United States of America
For support: supp[email protected]
For sales enquiries: [e-mail]

Quick Installation Guide Installation
deliberant Page 7
Installation
This chapter provides installation instructions for the hardware components of the APC 5M-18 V2.
Package Contents
The figure below displays APC 5M-18 V2 package contents.
Figure 1 –APC 5M-18 V2 Package Contents
Item
Component Name
Quantity
A
APC 5M-18 V2 Quick Installation Guide
1
B
APC 5M-18 V2 enclosure
1
C
Power adapter
1
D
PoE injector
1
E
Gland cap for the CAT5 Ethernet cable
1
F
Rubber gasket for the CAT5 Ethernet cable
1
G
Mounting bracket for wall/pole mount
1
H
U bolt M6 for pole mounting
1
I
Hexagon bolt M6 x 18 for wall/pole mount
1
J
Hexagon lock nut M6
3
K
Anti-slip washer M6
1
If any of these items are missing or damaged, please contact your reseller.

Quick Installation Guide Installation
deliberant Page 8
Hardware Introduction
APC 5M-18 V2 is housed in a plastic enclosure ensuring a reliable sealing in a wide range of
temperature and has an integrated 18dBi panel antenna.
Figure 2 –APC 5M-18 V2 Overview
The panel of the APC 5M-18 V2 contains:
Ethernet/Power connection in the form of passive PoE through standard Ethernet cable
6 LEDs: power LED, LAN activity LED and 4 LEDs for device RSSI level indication
Grounding stud
The APC 5M-18 V2 has label with the following information:
Figure 3 –APC 5M-18 V2 Label
The label of the APC 5M-18 V2 contains:
Model name. The official model name is APC 5M-18 V2.
Serial Number
Radio MAC address
LAN MAC address
FCC ID: UB8-APC5M18V2
IC ID: 6607-APC5M18V2
LEDs
The APC 5M-18 V2 has 6 LEDs located on the side panel: power, LAN and 4 RSSI LEDs. The
various states of the LEDs indicate different connection operations as follows:
LED
Color
Status
Indication
Power
Green
On
APC 5M-18 V2 is active/working
Off
No power on APC 5M-18 V2
LAN
Green
On
LAN connection exists.
Blinking
Indicates the traffic on LAN interface.
Off
No LAN connection.
RSSI (1, 2, 3, 4)
Yellow
On
The RSSI level has reached the appropriate threshold
level (default RSSI threshold levels: 10, 25, 35, 50)
Off
The RSSI level has not reached the appropriate
threshold level

Quick Installation Guide Installation
deliberant Page 9
Assembling and mounting the APC 5M-18 V2
The APC 5M-18 V2 units are supplied with mounting hardware for pole with diameters in the range
40mm to 50mm installations. After the unit is attached, its position is fixed with the single bolt. Follow
the steps for APC 5M-18 V2 assembling:
Step 1. Make sure that the APC unit is powered-off.
Step 2. Ground the APC 5M-18 V2 unit. The unit must be properly grounded to protect against
lightning. The grounding wire must be attached to the grounding stud on the unit (refer
at the Figure 2 –APC 5M-18 V2 Overview).
If the unit is attached to a metal pipe which is earth-grounded, no further grounding is
required.
Step 3. Attach mounting hardware (item C in the Figure 1 –APC 5M-18 V2 Package Contents)
to the unit and tighten with the nut and bolt (items I and J in the Figure 1 –APC 5M-18
V2 Package Contents).
For wall mounting, first attach the mounting bracket to the wall and then connect the unit
together and tighten the nut and bolt.
It is recommended not to tighten the unit to its mounting hardware until the alignment
process of the antenna is complete.
Step 4. For pole mounting attach APC 5M-18 V2 on pole with U bolt (items H and J in the
Figure 1 –APC 5M-18 V2 Package Contents) as shown in picture below:
Step 5. Connect Ethernet cable into the APC 5M-18 V2 then insert a rubber gasket (item F in
the Figure 1 –APC 5M-18 V2 Package Contents) into CAT5 Ethernet connector gland
and tighten with gland cap (item E in the Figure 1 –APC 5M-18 V2 Package Contents)
as displayed below:

Quick Installation Guide Installation
deliberant Page 10
It is recommended to use shielded STP Ethernet cable to reduce exposure of the
electromagnetic noise.
Step 6. Connect power adapter into PoE injector together with UTP cables as displayed in
picture below:
Step 7. Power-up the unit. The green Power LED must be on (refer at the respective section
LEDs). Depending on link quality, up to four yellow LEDs will switch on indicating that
link between two units was established successfully.
Step 8. After the link was established, align the antenna for the maximum performance. Run
the Antenna Alignment tool in the Web management interface and move the unit in
the horizontal and vertical planes until the maximum RSSI visible on the Antenna
Alignment graph is achieved. After the maximal RSSI is reached, tighten down the unit
in the optimum position.
Avoid standing directly in front of an operating antenna while aligning.

Quick Installation Guide Access the APC 5M-18 V2
deliberant Page 11
Access the APC 5M-18 V2
The first connection to the APC 5M-18 V2 can be made using a standard Ethernet cable connected
directly to your PC. See next sections for the instructions on how to access the APC 5M-18 V2
management interfaces.
Connection via WEB Browser
The default IP address of the APC 5M-18 V2 is 192.168.2.66 with a subnet mask of 255.255.255.0.
Step 1. Configure your PC with a static IP address on the 192.168.2.0 subnet with mask
255.255.255.0. Connect the APC 5M-18 V2 Ethernet interface in to the same physical
network as your PC. Open the Web browser and type the default IP address of the
APC 5M-18 V2: https://192.168.2.66/
Step 2. Enter the APC 5M-18 V2 administrator login details to access the Web management:
The default administrator login settings for all APC 5M-18 V2 are:
Login: admin
Password: admin01
Step 3. After successful administrator log on you will see the main page of the APC 5M-18 V2
Web management interface. The APC 5M-18 V2 now is ready for configuration. For
further instructions on Web management refer to the respective document APC 5M-18
V2 User Guide.

Quick Installation Guide Access the APC 5M-18 V2
deliberant Page 12
Resetting to Factory Defaults
APC 5M-18 V2 has the capability of being reset to defaults by pinging the device with a certain packet
size when the device is booting. During the startup of the device, when the drivers of the ethernet
interfaces are loaded, the reset daemon is started. The daemon suspends startup process for 3
seconds and waits for ICMP "echo request" packet of length 369 bytes. If the packet received, the
reset daemon sets the device to default configuration.
It is recommended to connect PC to the device via switch, as depending on PC OS
settings, the ARP table might be flushed during wired link status change (connecting the
device that will be reset).
Steps to reset to default settings:
Step 1. Power off the APC 5M-18 V2 device.
Step 2. Obtain the device MAC address.
Step 3. Connect a PC to the same physical subnet as the device.
Step 4. Execute 'arp -s' command to assign the IP address (IP address should be from the
same subnet as PC) to the device MAC address:
arp -s <IP address to assign> <device MAC address>
Note that syntax of MAC address differs depending on OS:
Linux OS: AA:BB:CC:DD:EE:FF
Windows OS: AA-BB-CC-DD-EE-FF
Step 5. Start pinging the APC 5M-18 V2 device:
For Linux users: ping <IP address> -s 369
For Windows users: ping <IP address> -l 369 -t -w 200
Step 6. Power up device and wait about 30sec or more (depending on device hardware).
Step 7. Stop pinging the APC 5M-18 V2, and let the device boot as usual. The device should
start up with factory default settings.