Dell INSPIRON Inspiron 5000 User manual

Dell Embedded Box PC
5000
Installation and Operation Manual
Computer Model: Dell Embedded Box PC 5000
Regulatory Model: N01PC
Regulatory Type: N01PC001

Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
©2016-2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries.
Other trademarks may be trademarks of their respective owners.
2017 - 12
Rev. A03

Contents
1 Overview......................................................................................................................... 5
2 Features..........................................................................................................................6
Top view............................................................................................................................................................................. 6
CANbus connector mapping......................................................................................................................................... 7
VGA connector mapping.............................................................................................................................................. 8
12-26V DC power port (barrel connector).................................................................................................................... 8
+12-26V DC power connector.......................................................................................................................................8
Bottom view.......................................................................................................................................................................9
GPIO-in connector mapping........................................................................................................................................10
GPIO-out connector mapping......................................................................................................................................11
RS232 connector mapping...........................................................................................................................................11
RS422 connector mapping..........................................................................................................................................12
RS485 connector mapping..........................................................................................................................................12
3 Setting up the Embedded Box PC..................................................................................13
Mounting the Embedded Box PC on the wall....................................................................................................................16
4 Setting up your operating system.................................................................................. 19
Ubuntu Desktop................................................................................................................................................................19
Reinstalling Ubuntu Desktop....................................................................................................................................... 19
Restoring Ubuntu Desktop......................................................................................................................................... 20
Restoring Ubuntu Desktop on the Embedded Box PC from the recovery USB ash drive......................................... 20
Creating the bootable USB ash drive........................................................................................................................20
Creating the recovery USB ash drive........................................................................................................................20
Reinstalling Ubuntu Desktop.......................................................................................................................................20
Windows OS..................................................................................................................................................................... 21
Windows 7 Professional SP1........................................................................................................................................21
Windows 7 Professional for Embedded Systems SP1................................................................................................. 24
Windows Embedded Standard 7 P/E......................................................................................................................... 26
Windows 10 Professional............................................................................................................................................ 28
Windows 10 IoT Enterprise LTSB 2015........................................................................................................................ 31
Recommended drivers and applications for Embedded Box PC..................................................................................33
5 Specications................................................................................................................37
6 Activating your mobile broadband service..................................................................... 40
7 Setting up the ZigBee dongle.........................................................................................41
8 Display options.............................................................................................................. 42
3

9 Connector kits...............................................................................................................43
Remote power connector.................................................................................................................................................43
12-26V DC power connector............................................................................................................................................ 43
GPIO-in connector........................................................................................................................................................... 43
GPIO-out connector.........................................................................................................................................................44
10 BIOS defaults.............................................................................................................. 45
General.............................................................................................................................................................................45
System conguration (BIOS level 1)..................................................................................................................................47
Video................................................................................................................................................................................48
Security (BIOS level 1)......................................................................................................................................................48
Secure boot......................................................................................................................................................................49
Intel software guard extensions........................................................................................................................................50
Performance.................................................................................................................................................................... 50
Power management......................................................................................................................................................... 50
POST behavior..................................................................................................................................................................51
Virtualization support (BIOS level 1).................................................................................................................................. 51
Wireless.............................................................................................................................................................................51
Maintenance..................................................................................................................................................................... 51
System logs......................................................................................................................................................................52
11 Contacting Dell.............................................................................................................53
4

1
Overview
The Embedded Box PC 5000 enables you to connect your devices (wired or wireless) to network-enabled devices and manage them
remotely in your existing network ecosystem. It enables you to connect with devices used in process and discrete manufacturing,
eet management, kiosks, digital signage, surveillance, and automated retail solutions. It can be either mounted on the wall using the
Dell approved wall mount kits or placed on a at surface. It supports Windows 7 Professional SP1 64-bit, Windows 7 Professional for
Embedded Systems SP1 64-Bit, Windows Embedded Standard 7 P/E 64-bit,Windows 10 Professional 64-bit, Windows 10 IoT
Enterprise LTSB 2015 64-bit, and Ubuntu Desktop 16.04 operating systems.
5

2
Features
Top view
Features
1 PCI or PCIe(x8) slot one Install a PCI card or a PCIe(x8) card.
Maximum card size supported: Height 111.15 mm (4.38 inches),
length 167.65 mm (6.6 inches)
2 PCI or PCIe(x8) or PCIe(x16) slot two Install a PCI card or a PCIe(x8) card, or PCIe(x16) card.
Maximum card size supported: Height 111.15 mm (4.38 inches),
length 167.65 mm (6.6 inches)
3 Power switch Turn on or o the Embedded Box PC.
4 Remote power switch 1Install a remote power switch.
5 Hard reset Using a pin, press the button located in the pin hole to restart the
Embedded Box PC.
6 Network port one Connect an Ethernet (RJ-45) cable for network access. Provides
data transfer speeds up to 10/100/1000 Mbps.
7 USB 3.0 ports (4) Connect USB enabled devices. Provides data transfer speeds up
to 5 Gbps.
8 Network port two Connect an Ethernet (RJ-45) cable for network access. Provides
data transfer speeds up to 10/100/1000 Mbps.
9 DisplayPort two Connect a monitor or another DisplayPort enabled device.
Provides video and audio output.
NOTE: For more information about the display options, see
Display options.
10 DisplayPort one Connect a monitor or another DisplayPort enabled device.
Provides video and audio output.
NOTE: For more information about the display options, see
Display options.
6

Features
11 HDMI port Connect a monitor or another HDMI‑in enabled device. Provides
video and audio output.
12 CANbus port (optional) Connect to a CANbus port enabled device or dongles. For more
information, see CANbus connector mapping.
13 VGA port Connect a monitor or another VGA enabled device. Provides video
output. For more information, see VGA connector mapping.
14 12-26V DC power port (barrel connector) Connect a 12-26V DC power cable for supplying power to your
Embedded Box PC. For more information, see 12-26V DC power
port (barrel connector).
15 Audio ports (3) Connect a speaker, a headphone, a microphone, or a headset
(headphone and microphone combo).
NOTE: Connect the headset to the Line Out port.
16 +12-26V DC power connector Connect a 12-26V DC power connector for supplying power to
your Embedded Box PC. For more information, see +12-26V DC
power connector.
1 Connections made to these ports must use SELV circuits and the wire (26 AWG-18 AWG) must have Double Insulation (DI) or Reinforced Insulation (RI) to protect it from all
hazardous voltages. Torque the screws at 2.88 kg-cm (2.5 lb-in) to secure the wire to the connector.
CANbus connector mapping
Pin Signal Pin Signal
1 NC 6 NC
2 CAN_L 7 CAN_H
3 GND 8 NC
4 NC 9 NC
5 NC
Manufacturer part number ACES 59131-0093C-P01
https://acesna.com/
NOTE: This part number is for reference only and is
subjected to change.
7

VGA connector mapping
Pin Signal Pin Signal Pin Signal
1 RED 6 GND 11 NC
2 GREEN 7 GND 12 DDCDAT
3 BLUE 8 GND 13 HSYNC
4 NC 9 +5V 14 VSYNS
5 GND 10 GND 15 DDCCLK
Manufacturer part number FoxConn DZ11627-H530P-4F
http://www.foxconn.com/
NOTE: This part number is for reference only and is
subjected to change.
12-26V DC power port (barrel connector)
Pin Polarity
1 Ground
2 DC-IN
Manufacturer part number ACES 59130-0023C-P01
https://acesna.com/
NOTE: This part number is for reference only and is
subjected to change.
+12-26V DC power connector
8

Pin Polarity
1 Negative
2 Ground
3 Positive
Manufacturer part number ACES 59126-0023C-P01
https://acesna.com/
NOTE: This part number is for reference only and is
subjected to change.
Bottom view
Features
1 GPIO-in 8-pin port 1, 2, 4 Connect to a GPIO-out enabled device or dongle. For more
information, see GPIO-in connector mapping.
2 GPIO-out 8-pin port 2, 3, 4 Connect to a GPIO-in enabled device or dongle. For more
information, see GPIO-out connector mapping.
3 USB 2.0 ports (4) Connect USB enabled devices. Provides data transfer speeds up
to 480 Mbps.
4 Network status light one Indicates the network activity of network port one.
5 Power status light Indicates the power‑state of the Embedded Box PC.
6 Hard-drive activity light Turns on when the Embedded Box PC reads from or writes to the
internal storage device.
7 Network status light two Indicates the network activity of the network port two.
8 Mobile broadband antenna port two Connect a mobile broadband antenna to increase the range and
strength of the mobile broadband signals.
9 RS232/RS422/RS485 port four (congurable in
the BIOS)
Connect an RS232/RS422/RS485 cable to the Embedded Box
PC. For more information, see RS232/RS422/RS485 connector
mapping.
10 Mobile broadband antenna port one Connect a mobile broadband antenna to increase the range and
strength of mobile broadband signals.
11 RS232/RS422/RS485 port three (congurable in
the BIOS)
Connect an RS232/RS422/RS485 cable to the Embedded Box
PC. For more information, see RS232/RS422/RS485 connector
mapping.
9

Features
12 RS232/RS422/RS485 port two (congurable in the
BIOS)
Connect an RS232/RS422/RS485 cable to the Embedded Box
PC. For more information, see RS232/RS422/RS485 connector
mapping.
13 Wireless antenna port two Connect a wireless antenna to increase the range and strength of
wireless signals.
14 RS232/RS422/RS485 port one (congurable in the
BIOS)
Connect an RS232/RS422/RS485 cable to the Embedded Box
PC. For more information, see RS232/RS422/RS485 connector
mapping.
15 Wireless antenna port one Connect a wireless antenna to increase the range and strength of
wireless signals.
1 The GPIO-in port has 9 pins. Pin labels are GND and GP10 through GP17.
2 Connections made to these ports must use SELV circuits and the wire (26 AWG-18 AWG) must have Double Insulation (DI) or Reinforced Insulation (RI) to protect it from all
hazardous voltages. Torque the screws at 2.88 kg-cm (2.5 lb-in) to secure the wire to the connector.
3 The GPIO-in port has 9 pins. Pin labels are GND and GP00 through GP07.
4 Connections made to the GPIO-in/out port must use SELV circuits (30 Vmax) and must be protected by Double/Reinforced Insulation (DI)/(RI) from all hazardous voltages.
5 The antenna is shipped in a separate accessory box along with your Edge Gateway.
GPIO-in connector mapping
Pin Signal Pin Signal
1 GPI0 6 GPI5
2 GPI1 7 GPI6
3 GPI2 8 GPI7
4 GPI3 9 GND
5 GPI4
Manufacturer part number ACES 59128-0093C-P01
https://acesna.com/
NOTE: This part number is for reference only and is
subjected to change.
10

GPIO-out connector mapping
Pin Signal Pin Signal
1 GPO0 6 GPO5
2 GPO1 7 GPO6
3 GPO2 8 GPO7
4 GPO3 9 GND
5 GPO4
Manufacturer part number ACES 59128-0093C-P01
https://acesna.com/
NOTE: This part number is for reference only and is
subjected to change.
RS232 connector mapping
Pin Signal Pin Signal
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 GND
Manufacturer part number ACES 59131-0093C-P01
https://acesna.com/
NOTE: This part number is for reference only and is
subjected to change.
11

RS422 connector mapping
Pin Signal Pin Signal
1 TX- 6 NC
2 TX+ 7 NC
3 RX+ 8 NC
4 RX- 9 NC
5 GND
Manufacturer part number ACES 59131-0093C-P01
https://acesna.com/
NOTE: This part number is for reference only and is
subjected to change.
RS485 connector mapping
Pin Signal Pin Signal
1 DATA- 6 NC
2 DATA+ 7 NC
3 NC 8 NC
4 NC 9 NC
5 GND
Manufacturer part number ACES 59131-0093C-P01
https://acesna.com/
NOTE: This part number is for reference only and is
subjected to change.
12

3
Setting up the Embedded Box PC
WARNING: During the installation of the Embedded Box PC, the responsible party or integrator must use the power
adapter provided with the Embedded Box PC, or connect to a 12-26 VDC separate power source already present as part
of the clients installation. Always ensure that the available power source matches the required input power of the
Embedded Box PC. Check the input power markings next to power connector(s) before making connections.
WARNING: Before you begin any of the procedures in this section, read the safety information that shipped with your
Embedded Box PC. For additional best practices information, go to www.dell.com/regulatory_compliance.
WARNING: To ensure that the protection provided by the Embedded Box PC is not impaired, do not use or install the
Embedded Box PC in any manner other than what is specied in this manual.
WARNING: To provide additional power connections to the main network, use cables appropriate for the load currents
such as, 3-core cable rated 15 A at 90°C (194°F) minimum, which conform to either IEC 60227 or IEC 60245. The
Embedded Box PC accepts cables from 0.8 mm to 2.5 mm (18 AWG to 14 AWG).
WARNING: The symbol indicates hot surface or adjacent hot surface that can obtain temperature during normal
use that can cause a burn. Allow equipment to cool o or use protective gloves when handling to reduce risk of a burn.
WARNING: This product is designed for specic applications and must be installed by qualied personnel with RF and
regulatory related knowledge. The general user must not attempt to install or change the setting.
WARNING: Before installation, the two power inputs (Terminal Block or Power Jack) must be protected by 20 A fuses or
circuit-breakers, which are over current protection devices in front of the Embedded Box PC.
WARNING: The product shall be installed at a location where the radiating antenna is kept 20 cm away from nearby
persons in its normal operating condition to meet regulatory RF exposure requirements.
WARNING: Use only the antenna(s), which are approved by Dell.
WARNING: Connect a certied SELV power to either Phoenix connector or the Barrel connector only. The connection of
two power sources may damage equipment and present risk of re.
WARNING: If your equipment or accessories are provided with a detachable main supply cord set and has to be replaced,
ensure that the replacement cord set has an adequate voltage, current, and temperature rating for the country where the
equipment is installed. The cord set must comply to the local safety code, regulations, and law.
Professional installation instructions
Installation personnel
This product is designed for specic applications and needs to be installed by qualied personnel with RF and regulatory related
knowledge. The general user shall not attempt to install or change the setting.
Installation location
The product shall be installed at a location where the radiating antenna is kept 20 cm from nearby persons in its normal operation
condition in order to meet regulatory RF exposure requirements.
External antenna
Use only the antenna(s) which have been approved by the applicant. Non-approved antenna(s) may produce unwanted spurious or
excessive RF transmitting power which may lead to a violation of FCC/IC limits and is prohibited.
13

Components Frequency (MHz) Antenna Type Brand Gain (dBi)
Main Aux
WLAN 2412~2462 Dipole Laird 2.9 2.9
5180~5240 4.0 4.0
5260~5320 4.0 4.0
5500~5700 4.0 4.0
5745~5825 3.9 3.9
Bluetooth 2402~2480 2.9 2.9
WLAN 2412~2462 Monopole Taoglas Antenna
Solution Ltd.
2.82 2.79
5180~5240 4.11 4.51
5260~5320 4.11 4.51
5500~5700 4.11 4.51
5745~5825 4.11 4.51
Bluetooth 2402~2480 2.82 2.79
Installation procedure
Please refer to user’s manual for the detail.
WARNING: Please carefully select the installation position and make sure that the nal output power does not exceed
the limits set forth in relevant rules. The violation of these rules could possibly lead to serious federal penalties.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
• Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to
operate this equipment.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
14

NOTE: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all
WiFi product marketed in US must xed to US operation channels only.
Industry Canada Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.
Setting up the Embedded Box PC
1. Install the Embedded Box PC on a vertical surface such as a wall using wall-mount brackets or in a panel box.
2. Connect to your network in one of the following methods:
• Connect the network cable.
• Install the wireless antenna (WLAN 1 and WLAN 2) to enable the wireless connection.
• Install the mobile broadband antenna (WWAN 1 and WWAN 2) to enable the mobile broadband connection.
NOTE: For more information about connecting the wireless antenna to Dell Embedded Box PC, see the
documentation that is shipped with the wireless antenna.
NOTE: For more information about installing the WWAN card in the Embedded Box PC, see the Embedded Box PC
Service Manual at www.dell.com/support.
15

NOTE: Peripherals such as the wireless antenna, keyboard, and mouse are sold separately.
3. Connect devices using the I/O ports on your Embedded Box PC.
4. Connect the Embedded Box PC to the power source in one of the following methods:
• Connect the power adapter and tighten the sleeves on the adapter pin to secure it to the Embedded Box PC.
• Connect the power terminal block to the adapter port and torque the screws at 5.07 kilograms-centimeter (4.4 pounds-
inch) to secure it to the Embedded Box PC.
5. Turn on the Embedded Box PC, and complete the operating system setup.
NOTE: After the Embedded Box PC setup is complete, reinstall the dust covers on any unused ports.
Mounting the Embedded Box PC on the wall
Mount the Embedded Box PC on a wall by using the mounting brackets.
NOTE: The Embedded Box PC is shipped with only those screws that are required for securing the two mounting
brackets to the back of the Embedded Box PC.
1. Secure the two mounting brackets to the back of the Embedded Box PC by using eight M3x8 screws.
NOTE: Torque the screws at 3 to 3.4 kilograms-centimeter (2.6 to 3.0 pounds-inch).
16

2. Drill four holes in the wall that correspond to the holes on the mounting bracket.
3. Place the Embedded Box PC against the wall and align the holes on the mounting brackets with the holes on the wall.
4. Secure the Embedded Box PC to the wall.
NOTE: Torque the screws (M4x6) at 5 to 5.4 kilograms-centimeter (4.3 to 4.7 pounds-inch).
17

18

4
Setting up your operating system
WARNING: To prevent operating system corruption from sudden power loss, use the operating system to gracefully shut
down the Embedded Box PC.
The Embedded Box PC is shipped with one of the following operating systems:
• Windows 7 Professional SP1 64-bit
• Windows 7 Professional for Embedded Systems SP1 64-Bit
• Windows Embedded Standard 7 P 64-bit
• Windows Embedded Standard 7 E 64-bit
• Windows 10 Professional 64-bit
• Windows 10 IoT Enterprise LTSB 2015 64-bit
• Windows 10 IoT Enterprise LTSB 2016 64-bit
• Ubuntu Desktop 16.04
NOTE: For more information about Windows operating systems, see msdn.microsoft.com.
NOTE: For more information about Ubuntu Desktop operating system, see www.ubuntu.com/desktop.
Ubuntu Desktop
Reinstalling Ubuntu Desktop
Before reinstalling Ubuntu Desktop, ensure the following:
• Connect a keyboard, mouse, and monitor to the Embedded Box PC, or connect to the Embedded Box PC through a KVM
session, Dell Wyse Cloud Client Manager (CCM), or Dell Command | Monitor (DCM).
• Create a bootable USB ash drive.
NOTE: For more information about using the CCM, see the CCM documentation available at
www.cloudclientmanager.com.
NOTE: For more information about using the DCM, see the DCM documentation available at www.dell.com/
clientsystemsmanagement.
NOTE: Dell recommends that you create a recovery USB ash drive before installing Ubuntu Desktop for the rst time.
Follow these steps to reinstall Ubuntu Desktop:
1. Insert the bootable Ubuntu Desktop USB ash drive.
2. Turn on the Embedded Box PC.
3. Press F12 to access the boot menu.
4. Enable UEFI boot mode in System Setup and boot from the Ubuntu Desktop USB ash drive.
5. Select Dell recovery to start the Ubuntu Desktop installation.
6. Select the drive onto which you want to install the Ubuntu Desktop operating system.
7. After the installation is complete, restart the Embedded Box PC.
8. Follow the instructions on the screen to congure the Language, License Agreement, Location, Keyboard Layout, and User
name/password settings.
19

The Embedded Box PC restarts to boot Ubuntu Desktop successfully.
Restoring Ubuntu Desktop
You can restore Ubuntu Desktop on the Embedded Box PC to a new condition if you encounter any of the following situations:
• You are unable to start Ubuntu Desktop
• The Ubuntu Desktop operating system is damaged
Before restoring, create a recovery USB ash drive with the backup image.
Restoring Ubuntu Desktop on the Embedded Box PC from the recovery USB ash drive
1. Insert the recovery USB ash drive into the Embedded Box PC.
2. Turn on the Embedded Box PC.
3. Press F12 to access the boot menu.
4. Enable UEFI boot mode in System Setup and boot from the Ubuntu Desktop USB ash drive.
5. Select Dell recovery to start Ubuntu Desktop recovery.
6. Select the disk onto which you want to install the Ubuntu Desktop operating system.
7. After the installation is complete, restart the Embedded Box PC.
8. Follow the instructions on the screen to complete the Language, License Agreement, Location, Keyboard Layout, and User
name/Password settings.
The Embedded Box PC restarts to boot Ubuntu Desktop successfully.
Creating the bootable USB ash drive
1. Download the Ubuntu Desktop ISO image from www.ubuntu.com/download/desktop.
2. Follow the instructions provided at www.ubuntu.com/download/desktop/create-a-usb-stick-on-windows.
3. Reinstall the Ubuntu Desktop operating system from the bootable USB ash drive.
Creating the recovery USB ash drive
Create a recovery disk when installing Ubuntu Desktop for the rst time.
1. Turn on the Embedded Box PC.
2. Follow the instructions on the screen when you start the Embedded Box PC for the rst time.
3. Select Language, and click Continue.
4. Agree to the license agreement, and click Continue.
5. Select a location, and click Continue.
6. Select the keyboard layout, and click Continue.
7. Enter the user name and password, and then click Continue.
8. Insert a USB ash drive with 2 GB or more space to create the recovery USB ash drive, and then click Continue.
9. To create a startup disk, select USB stick user plugged, and then click Make Startup Disk.
The recovery USB ash drive is created.
Reinstalling Ubuntu Desktop
Before reinstalling Ubuntu Desktop, ensure the following:
• Connect a keyboard, mouse, and monitor to the Embedded Box PC, or connect to the Embedded Box PC through a KVM
session, Dell Wyse Cloud Client Manager (CCM), or Dell Command | Monitor (DCM).
• Create a bootable USB ash drive.
NOTE: For more information about using the CCM, see the CCM documentation available at
www.cloudclientmanager.com.
20