dellonda DG1 User manual

Thank you for purchasing a Dellonda product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Original Language Version
Refer to
instruction
manual
PROPANE GAS TOWER PATIO HEATERS 13KW
MODEL NO: DG1, DG2
1. SAFETY
9Read the installation, operating and maintenance instructions thoroughly before installing or using this equipment.
9 Ifthereisasmellofgas:shuto󰀨thegastotheappliance,extinguishanyopenames.Ifodourcontinuescontactgassupplier.
8DO NOTstoreorusepetrolorotherammablesubstancesinsidethehousingoftheheater.
8DO NOTstoreorusepetrolorotherammableliquidsorgasesinthevicinityoftheheater.
8DO NOTstoreagascylinderthatisnotconnectedforuseinthevicinityofthisoranyotherappliance.
WARNING! DO NOTuseindoors.Foruseoutdoorsorinamplyventilatedareas.
 Anamplyventilatedareaisonethathasaminimumof25%ofthesurfaceareaopen,seeg.1.
 (Thesurfaceareaisthesumofthewallsurface.)
WARNING!Notintendedtobeinstalledinrecreationalvehiclesand/orboats.
WARNING!Improperinstallation,adjustment,alteration,serviceormaintenancecan
 causeinjuryorpropertydamage.
9 Installationandrepairmustbecarriedoutbyaqualiedperson.
8DO NOTattempttoalterinanyway.
9 Thisproductmustbeinstalledandthegascylinderstoredinaccordancewiththelocalregulationsinforce.
8DO NOTobstructtheventilationholesofthecylinderhousing.
8DO NOTmove/transporttheappliancewheninoperation.Shuto󰀨thegascylinderortheregulatorbeforemoving.
8DO NOTmove/transporttheheateruntilithascooleddown.
9 Useonlythetypeofgasandthetypeofcylinderspeciedbythemanufacturer.
 TheLPcylinderusedwiththepatioheatermustmeetthefollowingsizerequirements:
 diameter31.8cmxheight58cm,15kgmaximumcapacity.
9 Protecttheproductfromstrongwindtopreventtilting.
9 Onlyuseonlevelgroundcapableofwithstandingtheweightoftheheater.
8DO NOTremovetheinjector(itisnotremovable).Itisforbiddentoconverttheappliancefromonegaspressuretoanothergas 
 pressure.
8DO NOTconnectthegascylinderdirectlytotheappliancewithoutaregulator.Useonlythetypeofgasspeciedintheinstructions.
9 Thewholegassystem(hose,regulator,pilotorburner)shouldbeinspectedforleaksordamagebeforeuseandatleastannually,bya
 suitablyqualiedperson.
9 Allleaktestingshouldbedonewithasoapsolution.Neveruseanopenametocheckforleaks,refertosection6.2.
8DO NOTusetheheateruntilallconnectionshavebeenleaktested.
9 Turno󰀨thegasimmediatelyifagassmellisdetected.TurncylindervalveOFF.Iftheleakisatthehose/regulatorconnectiontighten
 theconnectionandperformanotherleaktest.Ifbubblescontinueappearingcontactyoursupplier.Iftheleakisattheregulator/ 
 cylinderconnectiondisconnectfromcylinder,reconnectandperformanotherleakcheck.Ifsoapbubblesarestillseen,cylindervalve
 isdefective.Returncylindertoitsplaceofpurchase.
9 Keeptheventilationopeningofthecylinderenclosurefreeandclearofdebris.
8DO NOTpainttheradiantscreen,controlpanelortopcanopyreector.
9 Controlcompartment,burnerandcirculationairpassagewaysoftheheatermustbekeptclean.
9 Turno󰀨gaswhilstnotinuse.
9 LPregulator/hoseassemblymustbeprotectedfromaccidentaldamage.
9 Anyguardremovedforservicing/maintenancemustbereplacedbeforeoperation.
9 Keepsadultsandchildrenawayfromthehightemperaturesurfacetoavoidburnsofignitionofclothing.
9 Childrenshouldbecarefullysupervisedwheninthevicinityoftheheater.
8DO NOThangclothingorotherammablematerialsontheheaterorplacethemneartheheater.
2. INTRODUCTION
InnovativedesignofRadiantGasTowerPatioHeater.Traditionalfreestandingpatioheateridealforbothcommercialanddomesticsettings
includingopenworkshops,boatyards,patios,forecourts,gardensandterraces.Theburnerheadispositionedapproximately2.2mo󰀨the
groundandthemetalreectordirectsradiationdownwardsandoutwards.Variableheatoutputcontrolsmakeitfullyadjustable.Featuresafully
enclosedgascylinderchamberandsafetytipoverswitch.Suppliedwithwheelsforeasymanoeuvrability.Availableinblackorstainlesssteel.
Suppliedwithgashoseandregulator.Thisproductshouldonlybeusedinawellventilatedarea.
DG1,DG2|Issue:3(6)22/04/20
fig.1

3. SPECIFICATION
Modelno’s............................................................. DG1,DG2
Fuelconsumption....................................................... 945g/hr
Fuel...........................................................................Propane
Heatedarea...................................................................10m²
Output...........................................................................13kW
Dimensions(WxH)........................................850x2200mm
Max.gasbottlesize(WxH)..........................Ø325x700mm
4. CONTENTS
5. ASSEMBLY
5.1. STEP 1
5.1.1. Fixwheelbrackettobase.
5.2. STEP 2
5.2.1. Fixthe3postbracketsasshown.UseboltBBtojoinpostbracketstothestand.
5.3. STEP 3
5.3.1. Fixtheposttothe3postbrackets.UseboltsEEandnutsCC.Tightennutsandbolts.
Original Language Version
PART DESCRIPTION QT Y.
A Reectorouter 3
BReectorinner 1
CBurnerheadassembly 1
D Cylinderhousing 1
E Mainpole 1
F Gas hose 1
FF Reectorspacer 3
G Supportleg 3
H Base 1
IWheelkit 1
Step 1 Step 2 Step 3
DG1,DG2|Issue:3(6)22/04/20

5.4. STEP 4
5.4.1. Placethetankhousingoverthepost.
5.5. DG3 TABLE FOR TOWER PATIO HEATER (not supplied)
5.5.1. DG3tablerequirestobettedontothepostatthispoint.
5.6. STEP 5
5.6.1. Removefourboltsfromthebaseoftheburner.
5.6.2. Passthegashosedownthroughthepost.
5.6.3. Fixtheburnertothepost,useboltDD.Tightennutsandbolts.
5.7. STEP 6
5.7.1. PlacelargewashersGGonthe3reectorspacersFF.
5.8. STEP 7
5.8.1. Fixthereectorontothereectorspacersuse3xwingnutKK.
5.9. STEP 8
5.9.1. Raisethetankhousingandrestitonthepostplate.Beawarethatit
 mayfallifitisknocked.
5.9.2. Connectthegashosetotheregulator.
5.9.3. PlacetheLPGcylinderonthestand.
6. OPERATION
6.1. CONNECT GAS CYLINDER
6.1.1. Changethegascylinderinawellventilatedarea,awayfromanysource
 ofignition.
6.1.2. Liftthetankhousingandpropituponthetopofthepostbrackets.
NOTE: IftheDG3tableistteditwillneedtoberaisedbeforethehousing
 canberaised.Inthisinstancethehousingcannotbeproppeduponthe
 topofthepostbrackets.Asecondpersonwillberequiredtoholdthe
 tankhousingupwhilethegascylinderistted.
6.1.3. Checktheregulatorsealiscorrectlyttedandworkingcorrectly,seeg.2.
6.1.4. Usepropaneorbutaneonly.
6.1.5. Onlyusehoseandregulatorsuppliedwithheater.
6.1.6. Neveruseagascylinderwithadamagedvalveoradamagedcylinder.
6.1.7. Neverconnectanunregulatedcylindertotheheater.
6.1.8. GAS LEAKAGE
6.1.9. IntheeventofgasleakageDO NOTusetheheater.Thegassupply
 shouldbeshuto󰀨andthecauseshouldbeinvestigatedbeforeitisused
 again.
Step 4 Step 5 Step 6
Step 7
Step 8
fig.2
Original Language Version DG1,DG2|Issue:3(6)22/04/20

6.2. LEAKAGE TEST
WARNING! Never perform leak test near sources of ignition.
6.2.1. Gasconnectionsaretestedatthefactory.Acompletegastightnesscheckmustbecompletedattheinstallationsitepriortouse.
6.2.2. Makeasolutionofonepartliquiddetergentandonepartwater. Thesoapsolutioncanbeappliedwith spraybottle,brushorrag.Soap
 bubbleswillappearatthesiteofaleak.
6.2.3. Testmustbeperformedwithafullcylinder.
6.2.4. Makesurethesafetycontrolvalveisintheo󰀨position.Turnthegassupplyon.Inthecaseofaleakturnthegassupplyo󰀨,re-tighten
 anyttings,thenturnthegassupplyonandre-check.
6.3.  LOCATIONOFHEATERrefertog.3
▲DANGERTheuseofthisheaterinenclosedareasisdangerousandisprohibited.
6.3.1. Ensurethatadequatefreshairventilationisprovided.
6.3.2. Alwaysmaintainproperclearancefromcombustiblematerials,i.etop100cmandsides100cmminimum.
6.3.3. Placeonlevelsolidground.
6.3.4. Neveroperateinanexplosiveatmosphereforexamplewhereexplosiveorammablesubstancesarestored.
6.3.5. Protectfromstrongwind.Anchorsecurelytothegroundwithscrews,refertog.3A.
6.4.  TURNONrefertog.4
6.4.1. Turncylindervalvefullyon.
6.4.2. PressinandturnthevariablecontrolknobtoPILOTposition(counterclockwise).
6.4.3. Pressdownthevariablecontrolknobandholdinfor90secondsthenpresstheigniterbutton.Variablecontrolknobcanbereleased
 afterthepilotamelights.
6.4.4. Pilotamecanbewatchedthroughthesmallroundwindowlocatedbelowtheburnermesh.
6.4.5. Ifthepilotamedoesnotlightorgoesout,repeatsteps6.4.2and6.4.3.
6.4.6. Afterthepilotamelights,turnthevariablecontrolknobtomaximumpositionandleavetherefor5minutesbeforeturningtheknobto
 thedesiredtemperatureposition. 
6.5. TURN OFF
6.5.1. Turnthevariablecontrolknobtowardsthepilotposition,pushknobinandmoveknobtoo󰀨position.
6.5.2. Turno󰀨valveoncylindercompletely.
6.6. CHECK HEATER IMMEDIATELY IF:
 -heaterdoesnotreachtemperature,
 -burnermakesapoppingnoiseduringuse(aslightnoiseisusualwhentheburnerisextinguished).
 -smellofgasinconjunctionwithextremeyellowtipofburnerame.
7. STORAGE
7.1.  Alwaysturno󰀨thegasvalveonthegascylinderafteruse.
7.2.  Disconnectthevalvefromthecylinder.
7.3.  Checkthetightnessofthegasvalve.Checkgasvalvefordamage.Ifdamageissuspectedhaveitinspected/changedbyagas 
 stockist.
8DO NOTstorealiquidgascylinderinacellarorinplaceswithoutadequateairventilation.
8. MAINTENANCE
8.1. GAS HOSE
8.1.1. Checkthehoseatleastonceamonth,eachtimethecylinderischanged,orafteraperiodwhentheheaterhasnotbeenused.
8.1.2. Ifitshowssignsofcracking,splittingorotherdeteriorationitmustbechangedforanewhoseofequivalentlengthandquality.
8.2. CLEANING
8.2.1. Wipesurfaceswithasoft,moistrag.DO NOTusecombustibleorcorrosivecleaners.
8.2.2. Removedebrisfromtheburnertokeepitsafeforuse.
8.2.3. Covertheburnerunitwiththeoptionalprotectivecover(Modelno.DG4)whennotinuse.
fig.3
fig.3A
fig.4
Original Language Version DG1,DG2|Issue:3(6)22/04/20

ENVIRONMENT PROTECTION
Recycleunwantedmaterialsinsteadofdisposingofthemaswaste.Alltools,accessoriesandpackagingshouldbesorted,takento
arecyclingcentreanddisposedofinamannerwhichiscompatiblewiththeenvironment.Whentheproductbecomescompletely
unserviceableandrequiresdisposal,drainanyfluids(ifapplicable)intoapprovedcontainersanddisposeoftheproductandfluids
accordingtolocalregulations.
Note:Itisourpolicytocontinuallyimproveproductsandassuchwereservetherighttoalterdata,specificationsandcomponentpartswithoutprior
notice.
Important:NoLiabilityisacceptedforincorrectuseofthisproduct.
Warranty:Guaranteeis12monthsfrompurchasedate,proofofwhichisrequiredforanyclaim.
WEEE REGULATIONS
DisposeofthisproductattheendofitsworkinglifeincompliancewiththeEUDirectiveonWasteElectricalandElectronicEquipment
(WEEE).Whentheproductisnolongerrequired,itmustbedisposedofinanenvironmentallyprotectiveway.Contactyourlocalsolid
wasteauthorityforrecyclinginformation.
9. TROUBLESHOOTING
PROBLEM CAUSE SOLUTION
Pilot will not light GasvalveOFF Turngasvalveon
Gascylinderempty Renewcylinder
Openingblocked Cleanorreplaceopening
Airinsupplysystem Purge air from lines
Loose connections Tighten connections
Pilotwillnotstayon Debrisaroundpilot Cleandirtyarea
Loose connections Tighten connections
Thermocouplefaulty Replacethermocouple
Gasleakintheline Checkconnections
Lackoffuelpressure Cylindernearlyempty.Renewcylinder
Burner will not light Pressure is low Cylindernearlyempty.Renewcylinder
Openingblocked Removeandclean
Control not ON TurnvalvetoON
Thermocouplefaulty Replacethermocouple
Pilotlightassemblybent Repositionpilotlight
Notincorrectlocation(toowindy) Positionproperlyandretry
Original Language Version DG1,DG2|Issue:3(6)22/04/20
Dellonda Ltd.,KempsonWay,SuffolkBusinessPark,BuryStEdmunds,Suffolk.IP327AR
01284757575  [email protected]www.dellonda.co.uk

Dellonda, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757575 sales@dellonda
EC DECLARATION
OF CONFORMITY
Description and Function:������������������������������������������������������������������������������������������������������������������������������������������������������������������������
Model/Type:���������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������
This declaration of conformity is issued under the sole responsibility of the manufacturer:
Dellonda, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
Declaration of Conformity in accordance with the above Directive(s)�
Technical le compiled by: Dellonda
Being the responsible person appointed by the manufacturer.
Signed �����������������������������������������������������������������������������������
Date���������������������������������������������������������������������������������������
Name �������������������������������������������������������������������������������������
Position���������������������������������������������������������������������������������
Place: Bury St Edmunds
Propane Tower Patio Heater 13kW (Stainless Steel)
DG1 v1 DG2 v1
References to harmonised standard(s)
EN 16129:2013�����������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������������
29 January 2019
Steve Buckle�
Marketing Director�
2016/426/EU Gas Appliance Regulations
Notied Body: Kiwa Nederland B�V�
Wilmersdorf 50,
P�O� Box 137,
7300 AC APELDOORN�
Netherlands�
0063
Type Examination
18GR0438/00
Performed:
Issued the certicate(s):

DG & DG Issue 3 L 23/04/20
Dellonda, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757575 suppor[email protected] www.dellonda.co.uk
Page 1 of 2
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. Spare parts must be fitted by a competent person
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Parts Information:
Propane Gas Tower Patio Heater 13kW
Model No: DG1 & DG2

DG & DG Issue 3 L 23/04/20
Dellonda, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757575 suppor[email protected] www.dellonda.co.uk
Page 2 of 2
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. Spare parts must be fitted by a competent person
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
Parts Information:
Propane Gas Tower Patio Heater 13kW
Model No: DG1 & DG2
Item Part No. Description
1 DG. Butterfly Nut
2 DG. Flat Washer
3 DG. Reflector Parts (Inner)
4 DG. Reflector Parts (Outer)
5 DG. Flat Washer
6 DG. Double Headed Stud
7 DG. Flat Washer
8 DG. Protect Ring For Housing Lid
9 DG. Protect Ring For Tank Housing
10 DG. Tank Housing 'DG1 only'
-- DG. Tank Housing S/S 'DG2 only'
11 DG. Hexagon Screw
12 DG. Main Pole
12 DG. Main Pole S/S -DG2 Model Only
13 DG. Hexagon Screw
14 DG. Flange Nut
15 DG. Support Leg
15 DG. Support Leg S/S -DG2 Model Only
16 DG. Hexagon Screw
17 DG. Steady Box
18 DG. Base 'DG1 only'
-- DG. Base S/S 'DG2 only'
19 DG. Flange Nut
20 DG. Hexagon Screw
21 DG. Rivet
22 DG. Circlip
23 DG. Flat Washer
24 DG. Main Fire Pole Fixer
25 DG. Flat Screw
26 DG. Flat Screw
27 DG. Small Mesh
28 DG. Pipe
29 DG. Flat Screw
33 DG. Flame Screen
34 DG. Flat Screw
35 DG. Top Fire Plate
36 DG. Protection Mesh
Item Part No. Description
37 DG. Bottom Fire Plate
38 DG. Welded Part For Fire Plate
39 DG. Connect Plate
40 DG. Flat Screw
41 DG. Main Nozzle Positioning Units
42 DG. Intake Baffle
43 DG. Support Leg
44 DG. Flat Screw
45 DG. Main Injector
46 DG. Tilt Switch
47 DG. Flat Screw
48 DG. Butterfly Clip
49 DG. Steel Clip
50 DG. Flame Screen Base
51 DG. Observation Hole Baffle
52 DG. Flat Screw
53 DG. Main Fire Unit
54 DG. Thermocouple
55 DG. Ignitor Electrode
56 DG. Main Injector Connection
57 DG. Valve
58 DG. Small Mesh Base
59 DG. Flat Screw
60 DG. Valve Support
61 DG. Valve Connection
62 DG. Control Panel
63 DG. Valve Fixer
64 DG. Knob
65 DG. Ignitor Fixer
66 DG. Ignitor
67 DG. Gas Hose
68 DG. Gas Regulator
101 DG. Fire Plate Assembly (35-39)
102 DG. Thermocouple Support Assembly (21,48,49)
103 DG. Nozzle Support Assembly (41-43)
FK DG.FK Hardware Kit