Delta Electronics USB Interface CME-USB01 User manual

2007-07-09
5011659301-SBT
1
CME-USB01 USB Interface for VFD-E Series Instruction Sheet
Please thoroughly read this instruction sheet before installing option cards and putting them into
use.
The content of this instruction sheet may be revised without prior notice. Please consult our
distributors or download the most updated version at http://www.delta.com.tw/industrialautomation/.
XLayout
USB Card (CME-USB01)
YInstallation
 Make sure that the AC Motor Drive is powered
off before operation. DO NOT insert or remove
the card when the AC Motor Drive is powered
on.
 Please mount the extension card as shown and
fix it with the screw packed with the card.
Screw torque:
Maximum 2kgf-cm
 USB Cable
USB Type B to CME-USB01 USB Type A to PC
NOTE
 Refer to Chapter 5: Parameters 9 (Group 9) in
the user manual for further details.
ZSpecification
 Environmental
Operating
Temperature
-10oC to 50oC (non-condensing
and not frozen)
Storage
Temperature -20oC to + 60oC
Ambient
Humidity
Less than 90%RH
(non-condensing)
Installation
Altitude Below 1000m
Vibration
Less than 20Hz:
Maximum 9.81 m/s2(1G);
20 ~ 50Hz:
Maximum 5.88 m/s2(0.6G)
NOTE
 Always use this product in a clean indoor
location free from dust, corrosive gas and liquid.
 Inputs/Outputs
Baud Rate Supports 4800, 9600, 19200,
38400, 57600 bps.
USB
Specification USB v1.1
[Notes
 Please use shielded wires to avoid interferences
and connect the shield to ground.
 To avoid interference, route the extension card
wires separately and as far away (at least 15cm)
as possible from other control wires, motor wires
and power wires, etc. Where these wires must
cross each other, please make sure they are at
a 90o angle.
 Always use and operate this product within the
limit of its specifications.

CME-USB01 VFD-E 系列之 USB 介面說明書
請詳細閱讀下列說明後才使用本產品，以確保使用安全。
由於產品精益求精，當內容規格有所修正時，請洽詢代理商或至台達網站
(http://www.delta.com.tw/industrialautomation/)下載最新版本。
X外觀
USB 卡(CME-USB01)
Y安裝方式
 安裝前請確認驅動器在斷電狀態下。
 請以下圖方式安裝擴充卡並使用包裝內的螺
絲固定以避免擴充卡鬆脫。
螺絲扭力
Maximum 2kgf-cm
 USB 傳輸線
USB Type B to CME-USB01 USB Type A to PC
NOTE
 詳細參數設定請參考使用手冊第五章參數，參
數群 9 (Group 9)說明。
Z規格
 環境
操作溫度 -10oC to 50oC
（無結露且無結凍）
儲存溫度 -20oC to + 60oC
環境溼度 90%RH 以下（無結露）
安裝高度 低於 1000m
震動
20 Hz 以下:
Maximum 9.81 m/s2(1G);
20 ~ 50Hz:
Maximum 5.88 m/s2(0.6G)
NOTE
 請使用此產品於無腐蝕性氣體、液體及無塵垢
的室內。
 輸入/輸出
鮑率 支援 4800, 9600, 19200,
38400, 57600 bps.
USB 規格 USB v1.1
[注意事項
 儘可能使用隔離線（隔離層接於大地），以避
免干擾。
 基於安規上的考量，配線請保持獨立且與其它
控制線，馬達線，電源線等保持 15cm 以上距
離，如有交錯的必要請保持垂直配線。
 任何時刻的操作皆不可超過規格上的限制。