DELTA GROUP VIVOTEK AP-GXC-0150 User manual

1. Install the device in a ventilated and dry place, that is free of electromagnetic source, vibration, moisture, and dust.
2. Make sure the ventilation openings on the extender are not blocked.
3. Use CAT.5e or 6 UTP/STP cables. Avoid using low-quality cables, which will seriously limit the cabling distance.
Outdoor Gigabit PoE Extender Series
Quick Installation Guide
IMPORTANT:
CONNECTION
• 1x Outdoor PoE Extender • 1x Quick Installation Guide
PACKAGE CONTENTS
Following are the conditions for making the cabling:
2. Typical cameras stream size feature = 1080p@30fps - 6Mbps; 720p@30fps - 3Mbps.
Make sure the combined bandwidth consumption does not exceed the uplink bandwidth from the PoE switch.
NOTE: There are power losses due to cable resistance.
INSTALLATION
PWR Green ON PoE IN port is connected to PSE.
OFF No PoE IN connection.
PoE Green or Amber ON Power over ethernet cable status
OFF Ethernet cable no Power
LAN Green ON Data link is detected.
Green Flashing Data is being transmitted or received.
OFF Link is not detected.
LED DEFINITIONS
*If the device that is going to be connected to this extender is not PoE PD, please turn off the PoE output function.*
AP-GXC-0150: 1 PoE IN - to - 1 PoE OUT.
AP-GXC-0250: 1 PoE IN - to - 2 PoE OUT.
The AP-GXC-0150/0250 is outdoor Gigabit PoE extender capable of receiving 90W IEEE 802.3bt PoE power from PSE.
Multiple extenders can be cascaded to increase the cabling distance.
INTRODUCTION
DIP SWITCH DEFINITIONS
Pin 1 ON Port 1 Turn on PoE output
OFF Port 1 Turn off PoE output
Pin 2
(AP-GXC-0250 only)
ON Port 2 Turn on PoE output
OFF Port 2 Turn off PoE output
56VDC PoE Output
Port 1 :
56VDC PoE Output
Port 2 :
56VDC PoE Output
Ground screw
* Make sure the
grouning resistance
Ground screw
* Make sure the
grouning resistance
PoE OFF/ON Switch
AP-GXC-0150
PoE Input
Connect to
PoE Switch
PoE Input
Connect to
PoE Switch
AP-GXC-0250
PoE OFF/ON Switch

NOTE:
The Outdoor PoE Extender must be grounded using
a ground wire between the ground screw and earth
ground.
IMPORTANT:
Ground screw
* Make sure the grouning
resistance is lower than
0.5
Outdoor 2-Port GbE PoE Extender
Out 1Out 2
PoE In
56VDC
24VDC
ON
OFF
PoE
12
2
1 2
1 2
Port:
To disconnect a LAN cable, loosen the cable
gland and pull the cable against the socket
wall towards the side of the locking tab.
PoE Output Port
Application
IMPORTANT -
please follow the procedures below carefully to ensure the best seal:
2. Thread the Cat5e/6 cable through the cap(A) & grip(B)
5. Thread the Cat5e/6 cable through the body(D)
6. Fit the washer(E) to the Outdoor PoE Extender connector
Extender
8. Hold Outdoor PoE Extender and then screw the body(D) onto the Outdoor
9. Push rubber(C) in the grip(B) and screw the cap tighten firmly. The
Cat5e/6 cable is sealed when the rubber(C) & grip(B) bulges to the edge
of the cap(A).
PoE Input Port Connector Assembly
Washer (E) Body (D) Rubber (C) Grip (B) Cap (A)
Rubber (C) Rubber (C)
Split
100m
100m
90W bt PoE Injector
PoE Extender PoE Extender
PoE100mPoE
PoE
100mPoE
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, NewTaipei City, 235, Taiwan, R.O.C.
|[phone]|F+886-2-82455532|E[email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298|s[email protected]
VIVOTEK Europe
Zandsteen 15, 2132 MZ Hoofddorp Delta Electronics
T:[phone] E:[email protected]m
::E:T:
Copyright © 2022 VIVOTEK INC. All rights reserved.