Delta-Opti RG-EST350-V2 User manual

1
Manufactured in China for:
DELTA-OPTI Monika Matysiak,
60-713 Poznan, 10 Graniczna St., Poland
www.shopdelta.eu
RG-EST350-V2 Wireless Bridge User Manual
Note
The device and software may update without prior notification. Please
contact Ruijie technical support for details.
Package Contents
Management software WSP-EST350 V2 has been installed on the device.
Part Description
Qty
RG-EST350 V2 Wireless Bridges
2
Phillips Pan Head Screws (ST4.2X19)
8
Hose Clamps
2
Mounting Brackets
2
Universal Joint Assemblies
2
Universal Joint Nuts
2
RG-EST350 V2 Product Manual
1
24V/0.5A PoE Power Adapters
2
Wall Anchors
6
Power Cord
2
Warranty Card
1
Before You Begin

2
Networking
LED & Ports
Description
1. LED
a. SYS LED
Blinking: The system is initializing, restoring factory settings,
LED & Ports
Camera
Camera - Switch (Optional) - Camera End
NVR End – Switch - NVR
Switch
Switch
NVR

3
upgrading or resetting.
On: The device is working properly.
Off: The device is not powered on.
b. LAN1/LAN2 LED
Off: The LAN port is not connected.
Blinking Green: Link is up. The port is sending or receiving data.
Solid Green: Link is up. The port is not sending or receiving data.
c. Signal LED (STR1/STR2/STR3)
STR1 Blinking/On: The device is bridged.
STR1 On: RSSI > -75 dBm
STR1 On + STR2 Blinking: RSSI > -73 dBm
STR1 On + STR2 On: RSSI > -71 dBm
STR1 On + STR2 On + STR3 Blinking: RSSI > -68 dBm
STR1 On + STR2 On + STR3 On: RSSI > -64 dBm
2. 12V DC Port
RG-EST350 V2 adopts 12 V/1 A DC power supply.
3. LAN2
4. LAN1/PoE Port
RG-EST350 V2 adopts 24 V/0.5 A PoE power supply.
5. Reset Button
Press the button for 2 seconds, and the device will be rebooted.
Press the button for over 5 seconds, and the device will restore the
factory settings.

4
NVR End
Camera End
Plugging the Ports
LAN1/PoE Port
PoE Power Adapter
PoE Max Distance: 100m (Cat5e/6/6a/7/8 Cable)
LAN1/PoE Port
PoE Power Adapter
PoE Max Distance: 100m (Cat5e/6/6a/7/8 Cable)

5
Pole Mounting
Wall Mounting
Installing the Device
Drill holes into the
marked positions and
insert wall anchors.
Adjust the orientation.
Secure the device on a
pole by using a hose
clamp.
Assemble the mount
kit.
Assemble the mount
kit.
Adjust the orientation.

6
App Management (Recommended)
The wireless bridges are used in pairs without extra configuration. You
can scan the following QR code to download an App to manage the
bridges.
Navigate to Project > + Create a Project > Scan QR-code to manage
the device.
Web Management
Connect to the SSID (Default: @Ruijie-bxxx. xxxx indicates the last four
digits of the MAC address) or plug an Ethernet cable into the LAN port,
and then visit http://10.44.77.254. It is recommended to set the IP address
of computer to 10.44.77.250.
Managing the Device