Delta 100 Series User manual

SINGLE HANDLE
KITCHEN FAUCETS
You may need the following tools:
T
E
F
L
O
N
Write purchased model number here.
Models 100,
103, 140, 141,
180, 300, 340,
400, 403, 440,
441, 480, D111
& D411 Series
ASME A112.18.1 / CSA B125.1
®
1
70701 Rev. B
SILICONE
T
E
F
L
O
N
?
SILICONE
T
E
F
L
O
N
For easy installation of your
faucet you will need:
• To READ ALL the instructions
completely before beginning.
• To READ ALL warnings, care,
and maintenance information.
• To purchase the correct water
supply hook-up.
1/13/12
®
UPC
www.deltafaucet.com

TABLE OF CONTENTS:
Warranty ------------------------------------------------------------- Page 2
Installation Instructions ----------------------------------------------- Pages 3-8
Maintenance -------------------------------------------------------- Page 9
Replacement Parts -------------------------------------------------- Pages 10-17
2
All parts and finishes of the Delta®faucet are
warranted to the original consumer purchaser to
be free from defects in material & workmanship
for as long as the original consumer purchaser
owns their home. Delta Faucet Company
recommends using a professional plumber for all
installation & repair.
Delta will replace, FREE OF CHARGE, during
the warranty period, any part or finish that proves
defective in material and/or workmanship under
normal installation, use & service. Replacement
parts may be obtained by calling 1-800-345-
DELTA (in the U.S. and Canada) or by writing to:
In the United States:
Delta Faucet Company
Product Service
55 E. 111th Street
Indianapolis, IN 46280
In Canada:
Masco Canada Limited, Plumbing Group
350 South Edgeware Road,
St. Thomas, Ontario, Canada N5P 4L1
This warranty is extensive in that it covers
replacement of all defective parts and even
finish, but these are the only two things that
are covered. LABOR CHARGES AND/OR
DAMAGE INCURRED IN INSTALLATION,
REPAIR, OR REPLACEMENT AS WELL AS ANY
Lifetime Faucet and Finish Limited Warranty
OTHER KIND OF LOSS OR DAMAGES ARE
EXCLUDED. Proof of purchase (original sales
receipt) from the original consumer purchaser
must be made available to Delta for all warranty
claims. THIS IS THE EXCLUSIVE WARRANTY
BY DELTA FAUCET COMPANY, WHICH DOES
NOT MAKE ANY OTHER WARRANTY OF ANY
KIND, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY.
This warranty excludes all industrial, commercial
& business usage, whose purchasers are
hereby extended a ve year limited warranty
from the date of purchase, with all other terms of
this warranty applying except the duration of the
warranty. This warranty is applicable to Delta®
faucets manufactured after January 1, 1995.
Some states/provinces do not allow the exclusion
or limitation of incidental or consequential
damages, so the above limitation or exclusion
may not apply to you. Any damage to this faucet
as a result of misuse, abuse, or neglect, or any
use of other than genuine Delta®replacement
parts WILL VOID THE WARRANTY.
This warranty gives you specic legal rights, and
you may also have other rights which vary from
state/province to state/province. It applies only
for Delta® faucets installed in the United States of
America, Canada, and Mexico.
© 2012 Masco Corporation of Indiana

1
3
2
1
1
1
Remove old faucet. For deck mount
models place gasket (1) on faucet.
For single hole mount models, place
base (1) then gasket (2) on faucet.
For models without spray, go to
Step 3. For models with spray, go
to Step 2.
SHUT OFF WATER SUPPLIES
NOTE: Thick tile 2 1/2" mounting
kits available.
103, 141, 403 & 441 Series–
RP30394.
Deck Mount Deck Mount
Single Hole Mount
Preparing for Installation

4
2
11
2
3
3
Mount the spray support assembly (1)
in far right hole in sink. Hand tighten
nut. Insert spray hose (2) down through
support assembly and up through center
For models with spray and spray support.
2
Sprayer Installation
hole on sink. Snap quick connect spray
hose (2) onto spray hose nipple (3). Pull
down moderately to ensure connection
has been made. Go on to Step 2.
2
2

1
3
2
Insert spray hose (1) down through support
assembly on escutcheon and hole in
sink. From underneath the sink place the
mounting nut (2) over spray hose and
insert the hose up through the middle hole
For models with integrated spray.
Sprayer Installation
in sink. From above the sink, snap the
quick connect spray hose (1) onto the
spray hose nipple (3) with quick connect
fitting. Pull down moderately to ensure
connection has been made.
5

6
3
1
1
2
2
Feed tubes (1) down through cen-
ter hole in sink. OPTION: If sink is
uneven, use silicone sealant under the
gasket. Secure faucet to sink
with nuts/washers or mounting
nuts (2) supplied with your faucet.
For deck mount models.
Faucet Installation
Deck Mount Single Hole Mount
Feed tubes (1) down through center hole
in sink. OPTION: If sink is uneven, use
silicone sealant under the gasket. Secure
faucet to sink with mounting bracket,
spacer (for thin mount only) and nut (2)
supplied with your faucet.
For single hole mount models.
2
2
2

7
4
1 2
3
1/2" (12.70mm) IPS
Water Hook-up
3750016
A. Note: Be careful when bending the
copper tubing. Kinked tubes will void
the warranty. Choose hook-ups for 1/2"
I.P.S. connections: (1) Ball nose riser
(3/8" O.D. copper tubing), or (2) 1/2"
I.P.S. faucet connector. Use the enclosed
coupling nuts (3) with the ball nose risers
(1). Coupling nuts are not included with
D111, D311 or D411 Series. Important:
Use two wrenches when tightening.
Do not overtighten.
A.
B.
12
B. Note: Be careful when bending the
copper tubing. Kinked tubes will
void the warranty. Solder connections
(1) or use compression fittings (2) for
3/8" O.D. (1/4" nominal) copper tubing.
Supply Line Connections
For models with fittings. For models without fittings.

8
5
2
3
1
Remove aerator (1) and turn faucet
handle (2) to the full on mixed position.
Turn on hot and cold water supplies (3)
and flush water lines for one minute.
Important: This flushes away any
debris that could cause damage to
internal parts.
Check all connections at arrows for
leaks. Re-tighten if necessary, but do
not overtighten.
Flush the System and Check for Leaks

9
3
2
4
7
6
1
If faucet leaks from under handle:
Remove handle and ensure cap (1) is tight.
If leak persists–SHUT OFF WATER
SUPPLIES. Replace Ball Assembly
(2)–Repair Kit RP70 and Cam & Packing
(3)–Repair Kit RP61.
If faucet leaks from spout outlet:
SHUT OFF WATER SUPPLIES. Replace
Ball Assembly (2)–Repair Kit RP70 and
Seats & Springs (4)–Repair Kit RP4993.
If faucet exhibits very low flow
A. Remove and clean Aerator (5), or
B. SHUT OFF WATER SUPPLIES. Clean
Seats and Springs (4) of any debris.
If spray attachment does not
function properly:
SHUT OFF WATER SUPPLIES. Remove
Diverter Assembly (6) and clean.
If condition persists–SHUT OFF WATER
SUPPLIES. Replace Diverter Assembly (6)–
Repair Kit RP63136.
If faucet leaks from base of spout:
SHUT OFF WATER SUPPLIES. Remove
spout and replace Spout O-Rings (7)–Repair
Kit RP25.
1/8" (3.18mm)
5
Maintenance Cleaning and Care
Care should be given to the cleaning
of this product. Although its finish is
extremely durable, it can be damaged
by harsh abrasives or polish. To clean,
simply wipe gently with a damp cloth
and blot dry with a soft towel.

Notes / Notas / Notes