Delton PW03W User manual

Wireless Magnetic Switch
The PW03W door and window mag netic switch transmits a wireless alarm or status signal to the
Meridian alarm control panel.
OVER VIEW
2 - : +t --t-
r
'
f:
ll)
r,j
i! 5
'
1. Double-Sided Tape
2. LED Indicator
3. Reed Switch
4. Magnet
5. S-S Button
6. Battery Cover
Back View Front View
The S-S button controls se lf-supervision for the magnetic contact. W hen this function is ""ON"", the
detector will send the control panel a signal every hour to report its working status.
Press the S-S button for an extended period when powering on to turn on or turn off the
supervision function .
TECHNICAL PARAMETERS
Operating Voltag e 12VDC ( 23A battery)
Standby Current: ≤10 µA (12VDC)
Operating Current
Working C urrent: ≤17mA ( 12VDC)
Low Voltage Alarm
6V±O. 5V
Active Gap
≥14mm
Operating Temperature
-1 O°C ~+55°C
Installation Mode
Fix to the door/window frame by double sided tape or screws
Transmitting Power
≤lOdB
Transmitting Frequency
868MHZ
INSTALLATION DIMENSION
37
For pet immunity, please ensure PIR installation height is no
greater than 1.8m. Refer detecting range in the above drawing.
1. Double-Sided Tape
2. LED Indicator
3. Reed Switch
4. Magnet
5. S-S Button
6. Battery Cover
Back View Front view
The PW03W door and window magnetic switch transmits a wireless alarm or status signal to the
Meridian alarm control panel.
OVERVIEW
Wireless Magnetic Switch PW03W
TECHNICAL SPECIFICATIONS
The S-S button controls self-supervision for the magnetic contact. When this function is
“”ON””, the detector will send the control panel a signal every hour to report its status.
Press the S-S button for an extended period when powering on to turn on or turn off the
supervision function.
INSTALLATION DIMENSION

1. Install the magnet on the movable parts of doors and windows and the reed switch on their frames.
2. The two parts should be installed completely parallel and the distance between them should
be less than 5mm (0mm is best) when the door or window is closed. If the distance is greater
than 5mm the magnetic switch will not function reliably.
3. Mount the magnetic switch in a place which is hard to reach.
OPERATING INSTRUCTIONS
1. Refer to the Meridian IP alarm installation manual for registering the PW03W wireless
magnetic switch to the alarm panel. The wireless ID number for registering the magnetic
switch with the alarm can be found inside the cover of the battery compartment.
2. Remove the bracket and the battery cover and remove the black insulation lm isolating the
battery. The LED ashes twice and the magnetic switch will activate.
3. The switch will check the voltage when powered on. If the voltage is lower than 6V±O. 5V
the LED ashes every 5 seconds and sends a low power signal to the Meridian control panel
after 10 seconds, then once every 1 hour.
4. When the switch is triggered by an intrusion it will send a signal to the control panel and the
LED will ash.
5. If the S-S (self-supervision} function is set on, the detector will send a signal to the control
panel every hour to report its status. This function is set to ON as a factory default. Press the
S-S button for an extended period when powering up to cancel this function and save battery
life. The LED ashes rapidly 6 times to conrm S-S cancellation success. When S-S is off,
press the S-S button for an extended period when re-powering to turn on supervision.
IMPORTANT
1. Please wait 5 seconds after removing old batteries and inserting new batteries to re-power
the magnetic switch.
2. Please install and use this product according to these instructions.
3. Avoid installing the product on metal doors and windows.
INSTALLATION
INSTALLATION
1. Fix the base with the screws or
double-sided tape provided.
2. Open the battery cover and remove
the black lm isolating the battery to
activate the magnetic switch.
Close the battery cover.
3. Push the magnetic switch down onto
the xed base.