Denali CANsmart DNL.DSP.12000 User manual

Instruction Rev00
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
Interactive Dealer Display
CANsmart Display
Instruction Manual
(a) Sheet Metal Base.................................................................Qty 1
(b) Display Wiring Harness (Lights).............................................Qty 1
(c) Self Tapping Screw...............................................................Qty 1
(d) Power Supply......................................................................Qty 1
(e) Battery Power Wiring Adapter................................................Qty 1
(f) Display Wiring Harness (Brake/Horn)......................................Qty 1
(g) Switch...............................................................................Qty 1
(h) M6 Screw...........................................................................Qty 2
(i) M6 Nut...............................................................................Qty 2
(j) Horn Mounting Bracket..........................................................Qty 1
Kit Contents
(k) Brake Light Mounting Bracket................................................Qty 1
(l) M4 Screw............................................................................Qty 1
(m) Zip Tie Anchor....................................................................Qty 3
(n) Zip Tie...............................................................................Qty 6
(o) Decal.................................................................................Qty 4
(p) Backdrop Sign.....................................................................Qty 1
(q) Adhesive Square.................................................................Qty 4
Tools Required: 13mm Wrench, 10mm Wrench, 4mm Allen Key, 2.5mm
Allen Key, Phillips Head Screwdriver, Razor Blade, Rubbing Alcohol
(a)
(c)
(e)
(h)
(g)
(f)
(b)
(d)
(m)
(i)
(j)
(k) (l)
(n)
(o)
(p)
(q)

1. Assembling The Display
1.1 - Applying The Decals
Step One: Prepare the top surface of the sheet metal base (a) using
rubbing alcohol. Allow to dry completely.
Note: The decals (o) should be applied from left to right in the following
order: B6, SoundBomb, D2, D4
Step Two: Peel and remove the backing from the decal (o)
Step Three: Beginning with one edge, apply the decal (o) to the sheet
metal base (a), slowly working your way across the surface to push out
any air bubbles.
DENALIELECTRONICS.COM
1.2 - Mounting The Product & Switches
Step One: Use a razor blade to cut out only the mounting holes highlighted
yellow from the decals.
Step Two: Attach the B6 mounting bracket (k) to the display base (a)
using the supplied bolt (h) and nut (i).
Step Three: Attach the B6 Brake Light (NOT INCLUDED) to the B6
mounting bracket (k) using the supplied M4 screws (l).
Step Four: Insert the push button switch (g) in the switch hole on the
bottom left of the display base (a).
Cut Out From Decal
(o)
(a)
1.3 - Mounting Continued
Step Five: Attach the horn mounting bracket (j) to the display base (a)
using the supplied bolt (h) and nut (i).
Step Six: Attach the SoundBomb Horn (NOT INCLUDED) to the horn
mounting bracket (j) using the hardware that came with the horn.
Step Seven: Use a 13mm wrench to attach the light pods (NOT
INCLUDED) to the display base (a).
Step Eight: Disconnect the switch from the wiring harness (b).
Step Nine: Use a screw driver and the included self tapping screws (c) to
secure the switch to the display base (a).
1.4 - Installing The Backdrop Sign
Step One: Prepare the back face of the sheet metal base (a) using
rubbing alcohol. Allow to dry completely.
Step Two: Apply an adhesive square (q) to each corner of the back face of
the display.
Step Three: Press the backdrop sign (p) against the adhesive squares (q)
with firm pressure to adhere the sign to the display.
(l)
(h)
(k)
(g)
(h)
(j)
(q)
(p)

3. Powering The Display
3.1 - Wall Powered
The DENALI 2.0 Interactive Dealer display can be plugged directly into an
100v-240v outlet, or by using the included battery power wiring adapter,
the display can be powered from a standard motorcycle battery, perfect for
those remote events where power isn’t available.
Step One: Plug the power supply (d) into the display harness (b) “power
input” barrel connector.
Step Two: Plug the power supply (d) into a standard wall outlet.
Step One: Plug the battery power adapter (e) into the display harness (b)
“power input” barrel connector.
Step Two: Connect the battery power adapter (e) to a standard automo-
tive battery via the ring terminals.
3.3 - Daisy Chaining Display Power
If there are multiple displays set up in one location it is possible to power
all the displays from a singular power supply or battery power source.
Step One: Connect the first display in the series to battery or wall power.
Step Two: Connect the “Power Output” of the first displays wiring harness
to the “Power Input” of the second displays wiring harness. Continue this
method until all displays have been connected together.
Note: The power supply has a maximum output of 10 Amps.
3.2 - Battery Powered
Wall Powered
Battery Powered
To 100-240V AC Wall Plug
To 12V DC Battery
12v DC Power (Input)
Display One
Display Two
Display Three
Power Output
Power Input
Power Output
Power Output
Power Input
Origin Power Source
(d)
(e)
(b)

2. Wiring The Display DENALIELECTRONICS.COM
2.1 - Connecting The B6 Brake Light
Step One: Route the brake light harness (f) up through the wire pass
through on the display base (a). Cut the spade terminals off the end of the
wiring harness (f) and use the Posi-Lock connectors that came with the B6
Brake light to attach the harness to the B6.
2.2 - Connecting The Switch
Step One: Connect the smaller female spades to the male spades on the
bottom of the switch (g).
12v DC Power (Output)
12v DC Power (Input)
(f)
To Switch (g)
To B6 Brake Light
Cut and Remove Spade Connectors.
Instead use Posi-Locks from B6
2.3 - Connecting The Light Pods
Step One: Pass the pod connectors and cables through the square holes
behind the pods. Then connect each pod to its mating connector on the
Display Wiring Harness (b).
2.4 - Connecting The Switch
Step One: Pass the switch connector and cable through the large hole in
front of the switch. Then connect the switch to its mating connector on the
Display Wiring Harness (b).
Step Two: Once all connections have been made, use the included zip ties
(n) and adhesive zip tie anchor (m) to neatly conceal the wiring to the
underside of the sheet metal display base (a).
Switch (4-Pin)
Light Pod Two (3-Pin)
12v DC Power (Input)
12v DC Power (Output)
Light Pod One (3-Pin)
(b)