Denver MLE-2401 User manual

MLE-2401
PC Monitor
Read this booklet thoroughly before using and save it for future reference

1. Product Overview
1.1 Monitor Buttons
1. M Menu Button: Press to display the OSD menu or enter sub-menus.
2. ▼ Down Button: Press to move do n in the menus.
3. ▲ U Button: Press to move up in the menus.
4. E Exit Button: Press to exit.
5. Power Button: Press to turn the monitor on/off.
6. LED Indicator: Change colors to indicate status.
1.2 Monitor Ports
7. Power Connector: Insert the po er cable to supply po er to the monitor.
8. Audio Out ut: Insert one end of the audio cable into the computer’s audio input to
receive the audio signals from your monitor.
9. VGA Connector: Insert one end of the VGA cable into the computer’s VGA output
and connect the other end to the monitor’s VGA port.
10. HDMI Connectors: Insert one end of the HDMI cable into the computer’s HDMI
output and connect the other end to the monitor’s HDMI port.
Eng- 2

2. Stand Installation
Keep the foam underneath the monitor before attaching the stand.
1. Open the package, take out the product ith foam attached, and gently place them
on a desktop or table.
2. Turn the bracket to a certain angle and align it ith the circular slot of the base, stick
it tightly, and then rotate clock ise to clamp the bracket into the base to complete
the installation of the base.
2.1 Make stand
aligned ith the
base slot.
2.2 Keep the
bracket and the
base close,
rotate the
bracket
clock ise.
2.3 Make the
bracket snap
into the base.
2.4 Lock the
scre s hich
contained in the
accessory bag
at the base
tightly
(PM4*12).
2.5 The
assembly is
completed.
3. Place the top of the mounted base frame flat on the lo er side slot of the rear case,
adhered and push up, then insert the base stand into the rear case.
Stand close to the back shell, and pull up.
Eng- 3

4. The assembled monitor is sho n as belo picture.
Note 1: Please do not put your hand in the gap bet een the stand and the case to
prevent pinching!
Note 2: After the base is installed, please avoid holding the base and invert the machine
to prevent falling!
To avoid damage, do not touch the screen hen moving the monitor.
3. Connectivity O tions
3.1 Connecting the Power Cable
Connect the included po er cable to the po er-in port of the monitor, and then plug the
other end into a all outlet.
Eng- 4

3.2 Connecting Your Ear hones
Plug in your earphones to receive audio signals from your monitor. If your earphones are
connected to the monitor and audio devices are connected to your computer at the same
time, the audio devices ill not produce sound. Earphones and other audio devices are
not supplied.
3.3 VGA Connectivity
In order for the monitor to receive VGA signals from the computer, use a VGA cable to
connect the monitor to the computer.
Eng- 5

3.4 HDMI Connectivity
In order for the monitor to receive HDMI signals from the computer, use the HDMI cable
to connect the monitor to the computer.
Eng- 6

4. Basic O eration
1. Insert one end of the HDMI cable into your PC’s HDMI port. A VGA cable may also
be used (not supplied).
2. Connect the other end of the cable to the corresponding connector on your monitor.
3. Connect the po er cable to your monitor then connect the other end to your po er
source. It is recommended that you use a surge protector ith adequate voltage if a
all outlet cannot be reached directly.
4. Locate the po er button on the monitor and press it to turn the monitor on.
FreeSync
The feature itself is off by default. To use this feature, you must have hard are ith
FreeSync capability, an HDMI cable, and the latest graphic drivers. To use this feature,
connect your computer and monitor ith an HDMI cable. After connecting, you may
receive a prompt to enable the feature on your computer, and then the FreeSync runs
automatically. If you do not receive the prompt, you may need to enable the function in
your graphics card menu. See your graphics card manufacturer’s documentation for
instructions on ho to turn on and/or enable FreeSync.
5. Indicator Light
Solid blue light indicates po er is on and the monitor is operating normally. Flashing blue
light indicates no video source has been detected. Red light indicates that no horizontal
Eng- 7

or vertical signal has been detected or voltage is lo . Please ensure your computer is on
and all video cables are fully inserted and/or connected.
10: ECO Modes and Game lus Switching
1. Press any one of the buttons (M, ▲, ▼, E, ) to activate the navigation indo .
2. Press ▼ to s itch Gameplus modes. According to the needs of your game, choose
the corresponding game icon. These game icons are primarily designed to optimize
your aim during shooting games, though they can be used for other scenarios.
3. Press ▲ to s itch ECO modes. These modes include Standard, Text, Movie, Game,
FPS and RTS modes and can be used to optimize settings according to your activity.
Standard mode is suitable for most activities.
Eng- 8

Please notice - All products are subject to change ithout any notice. We take
reservations for errors and omissions in the manual.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
Electric and electronic equipment contains materials, components and substances that
can be hazardous to your health and the environment, if the aste material (discarded
electric and electronic equipment) is not handled correctly.
Electric and electronic equipment is marked ith the crossed out trash can symbol, seen
above. This symbol signifies that electric and electronic equipment should not be
disposed of ith other household aste, but should be disposed of separately.
All cities have established collection points, here electric and electronic equipment can
either be submitted free of charge at recycling stations and other collection sites, or be
collected from the households. Additional information is available at the technical
department of your city.
DENVER ELECTRONICS A/S
Omega 5A, Soeften
DK-8382 Hinnerup
.facebook.com/denverelectronics
Eng- 9