Design SHIFT ORWL User manual

ORWL User Guide Document
USER GUIDE
FOR ORWL CONFIGURATION
Version 0.4

ORWL User Guide Document
Introduction 5
Hardware Requirements 5
Configuration of ORWL 6
Step 1: Power on ORWL 6
Step 2: Display Predefined (Shipping) PIN entry message 7
Step 4: Enter User pin 8
Step 5: User PIN Verification 9
Step 6: Display hash verification message 10
Step 7: KeyFob Association 11
Step 8: Display completion of configuration status 13

ORWL User Guide Document

ORWL User Guide Document
Revision History
Version
Date
Description of changes
Author(s)
0.1
09-May-17
Initial draft on ORWL configuration user
guide
Chaitra
0.2
13-06-17
Document modified based on the
comments provided by Daniel
Chaitra
0.3
27-Sep-17
Modification of User guide with respect to
latest OLED messages and flow of SuC
software.
Manjunath R S
0.4
11-Oct-2017
Updated the review comments provided by
Ravikiran
Manjunath R S

ORWL User Guide Document
1. Introduction
This document briefs on the steps to be followed to configure the ORWL device.
2. Hardware Requirements
The hardware equipments required are listed below:
● ORWL
● Power supply
Add an image of power supply
● HDMI cable
Add an image of HDMI cable

ORWL User Guide Document
● KeyFOB
3. Configuration of ORWL
Following are the steps to configure the ORWL device.
Step 1: Power on ORWL
Connect the Power adapter to the USB port just opposite to the Power button and switch on the
power supply. The position of button is shown in below figure.
“Welcome To ORWL message” followed by “ORWL” logo is displayed on OLED and this
message is displayed for few seconds.

ORWL User Guide Document
Step 2: Display Predefined (Shipping) PIN entry message
After timeout of ORWL logo “Please enter shipping PIN” is displayed followed by “Please press
power button to proceed.”
Follow instructions on the OLED. Once power button is pressed “PIN entry UI” is displayed. The
UI contains all the digits followed by a backspace icon. A cursor pointer(^) will indicate the digit
that is selected by the user.
Enter 6-digit predefined PIN received through mail.
Move the cursor to required digit’s position by holding the power button and release it to select
the respective digit.
User need to wait till a “*” is displayed for the next digit of PIN entry. Once the * is displayed
wait for the cursor to shift to a different position, then continue with the entering the next digit.
In case if the selected digit is wrong, then move the cursor to the Backspace icon and wait till it
clears the digit. Repeat the steps if needed to clear all the digits.
If pin verification is unsuccessful, it is indicated by a message “Verification Failed!” , followed by
“Please enter shipping PIN” further followed by “Please press power button to proceed” is
displayed. Follow the instructions OLED.
Verification failed

ORWL User Guide Document
If retry count of 3 is already tried, then a message “Wait till next PIN entry is allowed” will be
displayed.
Wait till next PIN entry is allowed
After the timeout, “Please enter shipping PIN” followed by “Please press power button to
proceed” is displayed.  Follow the instructions OLED.
If PIN verification is successful, “PIN verified” then it will continue with next step.
Step 3: Display User (custom) PIN entry message
Once Predefined PIN verification is successful, a message “Set custom PIN” followed by
“Please press power button to proceed” is displayed. Follow the instructions on OLED.
Step 4: Enter User pin
Due to security reasons User should not set PIN as “000000”. If tries to set he will be displayed
with a ne error message as show below.
“Invalid Password Please Try again”
Enter any 6-digit custom user pin to be set.
The UI contains all the digits followed by a backspace icon. A cursor pointer is also available
which shifts from digits to digits sequentially as user presses the power button. PIN digits need
to be selected by pressing the power button continuously. Once a digit is selected by moving
the cursor to that digit, stop pressing the power button for some time till the digit is written on the
UI. The UI is same as figure displayed in step 4.

ORWL User Guide Document
Once custom PIN entry is successful, a message “Re-Enter PIN” is displayed followed by
Please Press Power Button to proceed to confirm the PIN entered.
Follow instructions on OLED.
Enter the same 6-digit pin which is entered above to confirm the user pin.
If user pin configuration is successful, “Custom PIN set” message is displayed for few seconds
and flow continues with step 6.
If PIN configuration is unsuccessful, “PIN didn’t match Please retry...” message is displayed and
flow will be restarted from step 3.
Step 5: User PIN Verification
Once Custom PIN is set and in case the ORWL is restarted by user. Need to verify the User PIN
to login.
Following message “Enter your PIN” is displayed for few seconds followed by Please Press
power button to proceed.

ORWL User Guide Document
Press power button on the ORWL to continue. Enter the 6-digit custom pin which is configured
by user to verify the user. The UI is same as figure displayed in step 4.
If user pin verification is successful, “Login successful” message is displayed for few seconds
and flow will proceed with next step.
Otherwise, “Login failed” message is displayed and flow needs to started again from step 13.
Step 6: Display hash verification message
Message “VERIFY HASH Please press power button to confirm” is displayed to verify the hash
and ensure the safe shipment of ORWL to a valid user.
64 byte hash is displayed on the UI. User needs to verify the hash with the hash shared to them
via mail. If hash is correct, user needs to press the power button on the ORWL and flow
continues with next step.

ORWL User Guide Document
If HASH is incorrect when compared with the PIN mailer and OLED message. Just wait for 5
min timeout.
“HASH REJECTED CONTACT VENDOR OR RETRY AGAIN” message is displayed on timeout
and device needs to be shipped back to factory.
If HASH displayed is valid, User needs to press power button on ORWL to indicate proper hash
verification and safe shipment of ORWL. A message “ORWL received Untampered” is displayed
for few seconds.
“ORWL received Untampered”
Step 7: KeyFob Association
KeyFob LED will be Red if charging in progress.
KeyFob LED will be turned off once charging is complete.
KeyFob  LED be Green  when NFC authentication is in progress.

ORWL User Guide Document
A message “Pair KeyFOB to associate” is displayed.
Once the shipment is received, charge the keyfobs for at least 1 hour for it to get fully charged.
Present a KeyFOB on ORWL to proceed with the association process of KeyFOB with ORWL.
On successful association, an association image is shown and flow continues with next step.
Association in Progress will be displayed.
Do not move the keyfob or change the orientation of keyfob during association,until key
associated message is displayed.

ORWL User Guide Document
During association if keyfob is not presented within 15 seconds or keyfob removed before
complete association, then “Pairing Failed.. Please Retry by Presenting Again” message will be
displayed for few seconds.
Pairing Failed.. Please Retry by Presenting Again
Step 8: Display completion of configuration status
On completion of ORWL configuration, message “ORWL configured Rebooting…” is displayed.
Now ORWL is configured and it is ready for use.
Follow the instructions on OLED to use the ORWL.