Designplan ICE LED 1.0 User manual

ICE LED 1.0 - 1.1
Installation instructions
Ø0.79"
corrugato T 40°
Ta 25°
IP67
compliance
RoHS
LED
TECH
WARNING!!!
Please read the following instructions carefully.
IMPORTANT:
•Although LED runs on a very low voltage, always cut off the power sup-
ply before installing the LED light or subjecting it to maintenance.
•Unauthorised alterations or tampering of the product will invalidate all
the conditions of guarantee.
•This fixture must be istalled by a qualificate electrician.
•
Designplan Lighting is not resposable if its fixtures are not
installed in according to local safety standards.
•
Data contained in this document may be changed at any moment with-
out prior notice and do not place Designplan Lighting under any
implicit or explicit obligation.
ELECTRICAL CONNECTIONS:
•LED lights run at constant current.
•LED lights must be connected in series respecting polarities.
•As for the choice of the power supplies, please consider the current
through which they are feeded and the max power consumption of
LEDs you have to install.
•The total number of LEDs to be feeded must be counted for each single
spot (e.g. 2 spots with 3 LEDs 1W each= 6 LEDs 1W in all= 6W).
•The system must be feeded only if all the spots are connected. The
connection of the single spots with the power supply in voltage may get
the spot broken due to over-tension in vain.
•The power supplies must be installed in aerated rooms, far from heat
sources. A situation of overworking or a lack of air circulation will not
permit a natural dissipation.
•The electronic power supply is current-stable, therefore it partially com-
pensates the voltage-drop problems related to the cable length;
anyhow we suggest not to overcome 30 metres.
•Never use switches on secondary circuit.
NOTES:
• Wire connections must be realized with self amalgamating
scotch or similar.
!
ICE LED 1.0 ICE LED 1.1
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
1.57"x1.57" 2.36"x2.36"
2.01"
2.01"

1
2

POWER CONSUMPTION
max 1W;
SUPPLY VOLTAGE
220mA; 350mA;
POWER SUPPLY Notincluded.
CONNECTION Series connections
N°AND TYPE OF LED USED
1 power LED;
LED COLOURS AVAILABLE White: 5000K; 4000K; 3000K; 2700K; blue;
CRI 75-85
NGLE OF EMISSION (LIGHT BEAM)
D (diffuso);
TOTAL LUMINOUS FLUX
30 lm (3000K a 350mA)
OPERATING TEMPERATURE
0°C ÷ +45°C
FINISHING frosted glass
FIXING
WC0410 (Ice LED 1.0) WC0411 (Ice LED
1.1)
WEIGHT 0.84 lbs
IP RATE
IP67
WC0411
WC0410
Plug
WA NING!!!
LED LIGHTS MUST BE CONNECTED IN SE IES ESPECTING POLA ITIES.
THE SYSTEM MUST BE FEEDED ONLY ALL THE SPOTS HAVE BEING CONNECTED.
Series connection
COMPULSORY DRAINAGE
ICE LED 1.0 - 1.1
Installation instructions
Ø0.79"
corrugato T 40°
Ta 25°
IP67 RoHS
compliance
LED
TECH
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
1.57"
1.57"
1.61"
1.61"
3.94"
3.94"
3.94" 3.94"
2.36"
2.36"
2.9"
2.9"

3
5
IPS

IPS

Do not cut
4
Not for permanent submersion
in swimming-pools or
fountains .
IPS
BLACK-BLUE
RED-BROWN-WHITE
CONNETTERE RISPETTANDO LA POLARITA’
LED LIGHTS MUST BE CONNECTED
RESPECTING POLARITIES
Any metal part must not be in direct contact
with the ground or in contact with aggressive
chemical elements (ex. fertilisers, herbicides,
lime, aggressive cleaners).
Waterproof connection
ICE LED 1.0 - 1.1
Installation instructions
Ø0.79"
corrugato T 40°
Ta 25°
IP67 RoHS
compliance
LED
TECH
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042
Designplan Lighting, Inc., 79 Trenton Ave., Frenchtown NJ, 08825. T.908-996-7710 F.908-996-7042