DeWalt DXFRS220 User manual

Owner’s Manual
Printed in China
Part No. KEM-ML41402
English
PMN: WALKIE TALKIE TWO-WAY RADIO
DXFRS220
Owner’s Manual
DXFRS220

Staying in touch is convenient and easy when using your
radio. Some of the many uses you will discover include:
Communicating with others while hiking, biking, and working; keeping track of
family and friends at a crowded public event; checking with travel companions;
connecting with neighbors; arranging meeting spots
with others while shopping at the mall, talking with
your colleagues in warehouse or jobsite.
Secure your radio while on the go.
Carrying your radio with you is easy when using the
swivel belt clip.
The swivel belt clip easily attaches to your belt, purse,
or backpack.
Introduction
Making Life Easier and Safer
Customer Assistance
Product Service & Support
Swivel belt clip
A-1 A-2
WARNING: Important Safety Instructions for Battery
Read All Instructions
• Do not incinerate the battery even if it is severely damaged or is completely worn
out.
• Do not discard battery in a re. The battery pack can explode in a re.
• Do not replace battery in any area labeled “Hazardous Atmosphere”. Any sparks
created in a potentially explosive atmosphere can cause an explosion or re.
• Do not disassemble, crush, puncture, shred, or otherwise attempt to change the
form of your battery.
• Do not dry a wet or damp battery with an appliance or heat source, such as a hair
dryer or microwave oven.
• A small leakage of liquid from the battery cells may occur under extreme usage or
temperature conditions. This does not indicate a failure. Do not open, deform or
mutilate the battery as there may be corrosive materials which can cause damage
to eyes or skin and may be toxic if swallowed.
However, if the outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If battery liquid gets into your eyes, ush them with clean water for a minimum of
10 minutes and seek immediate medical attention.
This product uses Lithium Polymer Battery. Do not transport package if damaged, a
re hazard could exist.
For more information, please call our customer support line at [phone].
Recycle Battery
Local, state or federal laws may prohibit disposal of batteries in ordinary trash.
Consult your local waste authority for information regarding available recycling
and/or disposal options.
1. Only accessories included in this package or specied by the manufacturer
should be used with the radio. The 5V micro-USB charging input is compatible
with most high quality micro-USB chargers that fully conform to the USB
standards.
2. Do not use cleaners or solvents to clean the exterior of the radio. Use only a
damp or dry cloth.
3. Do not attempt to service the radio yourself. Removing the cover will void the
warranty. Changes or modications not expressly approved by DEWALT may
void the user’s authority granted by the FCC to operate this device and should
not be made.
4. Do not plug the wall adaptor into the power outlet if the outlet is wet.
WARNING: Important Safety Instructions
Before operating the radio, please read all safety and
operating instructions. Save all instructions in a safe place
for future reference.
For any questions about operating this new DEWALT branded product, PLEASE
CONTACT US FIRST… do not return this product to the retail store. The contact
information for support will vary depending on the country in which you
purchased and utilize the product.
To obtain warranty service or other information for products purchased from
Altis itself or through its authorized reseller or agent and utilized in the U.S.A.,
please call our consumer support line at [phone]. You will receive
instructions on how to ship the products at your expense to an our Authorized
Service Center. To obtain service, you must include: (a) a copy of your receipt,
bill of sale or other comparable proof of purchase; (b) a written description of
the problem; and, most importantly; (c) your address and telephone number.
For further information needed on its features, please visit DEWALT.COM for
frequently asked questions and the electronic manual.
©2019 Altis Global Limited, Atlanta, GA USA.

Introduction
Product Features
Customer Assistance
Operational Cautions
CAUTION: Exposure to high volume sound levels may cause
temporary or permanent damage to your hearing. Although there is no single
volume setting that is appropriate for everyone, you should always use your
radio with the volume set at low level and avoid prolonged exposure to high
volume sound levels.
1. Set the volume control in a low position and use as low a volume as
possible.
2. Avoid turning up the volume to block out noisy surroundings. Whenever
possible, use your radio in a quiet environment with low background noise.
3. Limit the amount of time you use headsets or earpiece at high volume
levels.
4. When using the radio without a headset or earpiece, do not place the radio’s
speaker directly against your ear.
5. Observe all signs and instructions that require an electrical device or RF
radio product to be switched off in designated areas, such as gas/refueling
stations, hospitals, blasting areas, potentially explosive atmospheres, or
aircraft.
6. If you experience a skin irritation after using this product, discontinue use
and seek medical attention.
7. If the product or charger: overheats; has a damaged cord or plug; has been
dropped or damaged; has been dropped into water, disconnect any charger
from its power supply, discontinue use of the product.
Electromagnetic Interference
Nearly every electronic device is susceptible to electromagnetic interference
(EMI) if inadequately shielded, designed, or otherwise congured for
electromagnetic compatibility. Turn off your radio in any facility where posted
notices instruct you to do so. These facilities may include hospitals or health
care facilities that may be using equipment that is sensitive to external RF
energy.
• When instructed to do so, turn off your radios when on board an aircraft. Any
use of a RF device must be in accordance with applicable laws, regulations
and airline crew instructions.
• Some radios may interfere with some hearing aids. In the event of such
interference, you may want to consult your hearing aid manufacturer or
physician to discuss alternatives.
• If you use any other personal medical device, consult the manufacturer of
your device to determine if it is adequately shielded from RF energy. Your
doctor or physician may be able to assist you in obtaining this information.
A-3 A-4
9
1 3 5 7
2 4 6 8
1. Talk Button
2. Power / Menu Button
3. LED Indicator
4. Built-In Microphone
5. Built-In Speaker
6. Micro USB Charge / Audio Jack
7. Volume / Channel (+) Button
8. Volume / Channel (-) Button
9. Swivel Belt Clip

1 2
Operation
Using Your Radio
Quick Start
1. Press and hold Power/Menu button for 4 seconds to turn the radio
on or off.
2. Select a desired channel.
3. Press and hold the Talk button while speaking into the microphone.
4. When nished talking, release the Talk button and listen for a
response.
Both radios must be tuned to the same
channel/privacy code to communicate.
Caring for Your Radio
Your radio will give you years of trouble-free service if cared for properly.
Handle the radio gently. Keep the radio away from dust. Never put the radio in
water or in a damp place. Avoid exposure to extreme temperatures.
Battery Information
The battery is not charged before delivery, so please charge the battery for
your rst use. If the battery is not used for a long time or the battery is used up,
please charge it before use. Charge / discharge for twice or three times
alternately to achieve its optimal performance.
Note:
• Do not cause any short circuit on the battery or throw the battery into re.
• When charging, please make sure the radio is powered off to guarantee it
can be fully charged.
• Unplug the charging cable after it is fully charged. Unnecessary constant
charging will shorten the battery life.
• Do not put the fully-charged battery to re-charge, or it may shorten the
battery life.
• Please try to keep the battery in an indoor environment at around 25°C. The
battery may get easily spoiled after being kept in the environment below
-10°C for a long time.
• In temperatures higher than 35°C or below -10°C, the dischargeable power
of the battery may decrease due to the physical property of lithium battery.
For charging radio(s):
1. Insert the micro-USB cable into jack located at the bottom of radios.
2. Plug the cable into USB compatible power port.
3. It will take around 5 hours for a full charge.
4. LED indicator
DEWALT recommends your radio be turned off while being charged.
Power Off the Device during charging
Battery Charging Solid Red (No ash)
Battery Charged Solid Green (No ash)

Communicating with Another Person
1. Press and hold the Talk button.
2. Position the microphone about 6 inches from your
mouth, speak in a normal voice.
3. Release the Talk button when you are nished
talking and listen for a response.
You cannot receive incoming calls while pressing the
Talk button.
To Select a Channel
To change the channel, press Power / Menu button
once, the current channel number prompted. Then,
press the +or –buttons to select your channel, and
you can:
1. Fast press to skip voice prompting of every channel
number
2. Press and hold for fast skipping
It will exit the channel selection mode if there is no +
or -button pressing for 5 sec. Or simply press Power
/ Menu button or Talk button once to return to
standby mode immediately.
Power/Menu Button
Up & Down Button
Up & Down Button
Battery Low
3 4
Turning on Your Radio
Press and hold Power/Menu button for 4 seconds to turn the radio on or off.
When green LED ashes every 5 seconds, your radio is now in Standby
mode, ready to receive transmissions.
The radio is always in Standby mode except when the Talk or Power/
Menu buttons are pressed.
Battery Low
Red LED ashes every 5 seconds. Voice prompt
“Please charge” will be heard approximately 30
minutes before device automatically powers off.
Auto Battery Save
If there are no transmissions within 10 seconds, the radio will automatically
switch to Battery Save mode. This will not affect the radio’s ability to
receive incoming transmissions.
Listening for a Response
Release the Talk button to receive incoming transmissions. Your radio is
always in Standby mode while the Talk button is not pressed.
To Adjust Volume
Press the +or –button to increase or decrease the
volume. There are 12 different volume levels.
Do not hold the radio close to your ear. If the volume is
set to an uncomfortable level, it could hurt your ear.
Talk Button
Both radios must be tuned to the same
channel and privacy code to communicate.

5 6
Range
Your range will vary depending on terrain and
conditions.
In at, open country your radio will operate at
maximum range.
Buildings and foliage in the path of the signal can
reduce the range of the radio.
Dense foliage and hilly terrain will further reduce the
range of the radio.
On Channels 8 through 14, your radio automatically
switches to low power, which will limit the range the
radio can communicate.
Auto Squelch
Your radio will automatically shut off weak transmissions and unwanted
noise due to terrain, conditions limit.
Call Alert
Your radio can alert you to incoming signals by sounding an audible call
tone.
Roger Beep Conrmation Tone
Your listener will hear an audible tone when you release the Talk button.
This alerts the other party that you have nished talking and it is OK for
them to speak.
Key Tone
Key Tone is an audible tone which will sound each time a button is pressed.
LED indicator
When you press and hold Talk button Green LED on
Standby Mode Green LED ashes every 5 seconds
Battery Low Red LED ashes every 5 seconds
Power Off the Device during charging
Battery Charging Solid Red (No ash)
Battery Charged Solid Green (No ash)

7 8
Operation
General Specications
Frequency Allocation and Compatibility
A = Channel No. for 22 Channel Models
B = Frequency in MHz
C = Power Output
A B C
1 462.5625 High
2 462.5875 High
3 462.6125 High
4 462.6375 High
5 462.6625 High
6 462.6875 High
7 462.7125 High
8 467.5625 Low
9 467.5875 Low
10 467.6125 Low
11 467.6375 Low
12 467.6625 Low
13 467.6875 Low
14 467.7125 Low
15 462.5500 High
16 462.5750 High
17 462.6000 High
18 462.6250 High
19 462.6500 High
20 462.6750 High
21 462.7000 High
22 462.7250 High
MODEL DXFRS220:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: 1) This device may not cause harmful interference, and 2)
this device must accept any interference received,including interference that may
cause undesired operation.
FCC Warnings: Replacement or substitution of transistors, regular diodes or other parts
of a unique nature, with parts other than those recommended by DEWALT may cause a
violation of the technical regulations of part 95 of the FCC rules, or violation of type
acceptance requirements of part 2 of the rules.
IMPORTANT NOTICE:
WARNING: Changes or modications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device must accept any
interference received,including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Safety Information for Radios
Your wireless handheld portable transceiver contains a low power transmitter. When the talk button
is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty
factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted
RF exposure guidelines with safety levels for handheld wireless devices
Important
FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the
FCC RF exposure guidelines when used with DEWALT accessories supplied or designated for this
product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use
only the supplied antenna. Unauthorized antennas, modications or attachments could damage the
transmitter and may violate FCC regulations.
Normal Position
Hold the transmitter approximately 2 inches from your face and speak in a normal voice, with the
antenna pointed up and away.
FCC Part 15.21 Warning Statement-
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
IC RSS-GEN
This device complies with ISED license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Under ISED regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
The applicant is responsible for providing proper instructions to the user of the radio device, and any
usage restrictions, including limits of exposure durations. The user manual shall provide installation
and operation instructions, as well as any special usage conditions, to ensure compliance with SAR
and/or RF eld strength limits. For instance, compliance distance shall be clearly stated in the user
manual.
Radiation Exposure Statement:
Any Changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
For Remote controller, SAR tests are conducted using standard operating positions accepted by the
FCC/ISED with the device transmitting at its highest certied power level in all tested frequency
bands, although the SAR is determined at the highest certied power level, the actual SAR level of
the device while operating can be well below the maximum value.
Before a new model device is available for sale to the public, it must be tested and certied to the
FCC that it does not exceed the exposure limit established by the FCC/ISED, Tests for each device
are performed in positions and locations (e.g. at the ear and worn on the body) as required by the
FCC/ISED.
For body worn operation, this model device has been tested and meets the FCC/ISED RF exposure
guidelines when used with an accessory designated for this product or when used with an accessory
that Contains no metal and that positions the handset a minimum of 10 mm from the body.
Non-compliance with the above restrictions may result in violation of RF exposure guidelines.

Warranty & Trademark Acknowledgment
9 10
Limited Lifetime Warranty on Radio
Altis Global Limited warrants to the original consumer purchaser only that this product and
the component parts thereof, will be free from defects in workmanship and materials. Altis
will, repair or replace, at its sole option and discretion, this product or any defective parts.
Altis’ liability hereunder shall be limited to repair or replacement of the defective part or
parts, and such correction shall constitute a fulllment of all of Altis’ warranties hereunder.
This limited lifetime warranty is only valid for the original consumer purchaser in limited
jurisdictions and is not transferrable. This limited lifetime warranty will automatically
terminate if this product is sold or otherwise transferred to another party. The product must
be purchased from Altis or an authorized dealer or the warranty is void. This limited lifetime
warranty is valid only for products purchased and utilized in specic jurisdictions. Please
visit our website at DEWALT.COM for a list of jurisdictions wherein this lifetime limited
warranty is valid.
This limited lifetime warranty does not apply to accessories and consumables and does not
cover damage due to misuse, abuse, negligence, acts of God, accident, commercial use or
modication of, or to any part of this product. The limited lifetime warranty does not include
battery, battery warranty is 180 days from original purchase date; after initial 180 days,
owner can return the Radio (at owner's expense) to Altis for review and can purchase a new
battery if necessary. This warranty does not cover damage due to improper operation,
maintenance or installation; ordinary wear and tear; or attempted alterations or repairs by
anyone other than Altis or someone authorized by Altis to do warranty work. Any
unauthorized alterations or repairs will void this warranty. This limited lifetime warranty
does not cover product sold AS IS or WITH ALL FAULTS. This limited lifetime warranty is
invalid if the factory applied serial number or date stamp has been altered, defaced or
removed from this product. This limited lifetime warranty does not cover product purchased
or utilized in a jurisdiction not covered.
The procedure for obtaining service and support, and the applicability of this warranty, will
vary depending on the country or jurisdiction in which you purchase and utilize the product.
For details on obtaining product service, support and other warranty information please visit
DEWALT.COM.
This warranty gives you specic legal rights, and you may also have other rights which vary
from state to state and country to country.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, ALTIS MAKES NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALTIS EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED
WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS
EXPRESSED WARRANTY.
LIMITATION OF REMEDIES AND DAMAGES. REPAIR OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ALTIS SHALL NOT BE
LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED
TO ATTORNEYS’ FEES AND/OR COSTS OF LITIGATION, FOR BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY ON THIS PRODUCT. ALTIS IS NOT LIABLE FOR ANY DAMAGES CAUSED
BY THE PRODUCT OR BY THE PRODUCT TO PERFORM, INCLUDING ANY LOST PROFITS, LOST
SAVINGS, INCIDENTAL DAMAGES, OR CONSEQUENTIAL DAMAGES. ALTIS IS NOT LIABLE
FOR ANY CLAIM MADE BY A THIRD PARTY OR MADE BY YOU FOR A THIRD PARTY. THIS
LIMITATION APPLIES WHETHER DAMAGES ARE SOUGHT, OR A CLAIM MADE, UNDER THIS
WARRANTY OR AS A TORT CLAIM (INCLUDING NEGLIGENCE OR STRICT PRODUCT LIABILITY),
A CONTRACT CLAIM, OR ANY OTHER CLAIM. THIS LIMITATION CANNOT BE WAIVED OR
AMENDED BY ANY PERSON. THIS LIMITATION OF LIABILITY WILL BE EFFECTIVE EVEN IF
ALTIS OR AN AUTHORIZED REPRESENTATIVE OF ALTIS HAS BEEN ADVISED BY YOU OF THE
POSSIBILITY OF ANY SUCH DAMAGES.
Some states and countries do not allow limitations on how long an implied warranty lasts
and do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations may not apply to you. This warranty gives you specic legal rights, and you
may also have other rights which vary from state to state and country to country.
Provided that the product was purchased from Altis itself or through its authorized reseller or
agent and utilized in the U.S.A., Altis will, without charge, repair or replace, at its option,
defective products, products or component parts upon delivery to the authorized Altis Global
Limited Authorized Service Center, accompanied by proof of the date of rst customer
purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for warranty service,
but the return charges, to an address in the U.S.A, will be at Altis’ expense, if the product is
under warranty.
For Products Purchased Outside the U.S.A.
Please contact your authorized local reseller or agent for warranty information.
Trademark Acknowledgment
DEWALT®and the DEWALT Logo are trademarks of the DEWALT Industrial Tool Co., or an
afliate thereof and are used under license.
The yellow/black color scheme is a trademark for DEWALT power tools & accessories.
© 2019 DEWALT
U.S. & Canada Only
Made in CHINA
Product Manufactured by:
Altis Global Limited, Atlanta, GA USA.
For product, service or warranty information contact us at:
DEWALT.COM [phone]