Dewenwils HCRA40B User manual

Thank you for your purchase.
Please contact us if you have any problem.
Email: [email protected]
Please attach your User Name or Order ID so that
we can assist you better.
Retractable Cord Reel
HCRA40B
Instruction Manual
01
◆ Warning: To reduce the risk of fire, electric shock or personal injury, please
strictly follow the instructions.
◆ Installation
1. Do not connect any devices which may exceed the maximum ratings of
this cord reel.
2. Do not try to plug it in when your hands are wet or damp.
3. Never attempt to plug the cord reel into a non-grounded outlet.
4. When pulling the cord from the cord reel, grasp the reel’s cord itself,
but not the device or tool that the cord is plugged into.
5. Do not allow the cable to retract without restraining the retraction speed
as damage or injury may occur from excessive rewind speed.
6. Inspect before every use; do not use if parts are loose or damaged or if
insulation is worn.
7. Always unplug the retractable reel from its electrical outlet before
performing any maintenance or changing accessories.
8. Do not disassemble the body of the reel.
9. Children are not allowed to use the cord reel.
Note:
a. Check to make sure the wall or ceiling surface to which the Retractable
Reel will be mounted is sturdy enough to support the weight of the Reel
as well as the additional force when pulling on the Outlet Power Cord.
b. Drywall will not hold the weight of the cord reel. It is necessary to locate
a ceiling joist or wall stud.
1. Select a mounting location within 4 feet of an electrical outlet. The outlet
for a garage door opener is ideal.
2. Locate a wall or ceiling beam (use a stud finder, if needed) and using the
mounting bracket as a template, mark the holes so they are centered on
the beam, see Figure1.
3. 3. Attach the mounting bracket to the beam using cement screws or wood
screw, see Figure 2.
02
Mark with a pen according to
the mounting position (Suitable
for concrete materials)
Install the bracket with
the anchor bolt and
tighten the nut
Install the bracket with
wood screws (Suitable for wood)
Mark with a pen
according to the
mounting position
(Suitable for concrete)
Drill four 45-50mm
deep holes with
10mm drill bits
Install the expansion
screws into the holes
Install the bracket with
the wood screws
(Suitable for wood)
Install the bracket
with the anchor bolt
and tighten the nut
Drill four 45-50mm deep
holes with 10mm drill bits
Install the expansion
screws into the holes

03
Slide the mounting bracket of the cord reel into the
separate bracket as shown (No need to use the set screw)
Slide the mounting bracket of the
cord reel in the separate bracket
as shown
Fix the set screw. (Please pay attention
to the position of the set screw, do not
fix it to another side or the cord reel will
fall off.)
04
One Year Limited Warranty
◆
◆
Package Includes
Cord Reel x 1
Instruction Manual x 1
Wood Screw x 4
Expansion Screw x 4
Set Screw x 1
Dewenwils warrants this product to be free from defects in material and
workmanship for a period of one year from the date of purchase. Warranty
is void if damage is caused by misuse or improper installation.
Email: [email protected]
Our dedicated customer service team will get back to you within 24 hours.
◆ Specifications
◆ Operation
Input Voltage:125VAC, 60Hz
Max Power Rating: 15A,
1875W
Cord
:
12AWG, SJTOW
Length: 40 FT
4. Adjust the cord stopper to a suitable position when required.
5. Plug the lead-in cord into the outlet.
1. Plug the lead-in cord into the grounded outlet.
2. Pull cord out to the desired length. Notice a clicking noise when pulling
the cord. The cord will stay at the desired length during the clicking and
rewind after a pull past the clicking noise.
3. To retract, pull the cord out and guide it slowly back into the reel.
NOTE:
Cord length is 40 feet long fully extended. DO NOT keep on pulling the
cord after it is fully extended.