DHP 3247198 User manual

DO NOT RETURN TO THE STORE !
Visit www.dhpfurniture.com/eng/support-home
or call Toll-Free 1-800-267-1739
3247198
B34324719802 - 241637-C
Date of Purchase
Metal Bed
K.W. - 2017/9/11
If parts are missing or damaged, we will gladly ship your
replacement parts free of charge.
Lot Number
Thank you for purchasing from DHP!
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
1
© 2014 Dorel Home Products All Rights Reserved
Full
Bronze
Weight Limit: 450 Lb / 204 Kg
TM
dorel home products

Contact Us!
[e-mail]
DHP Consumer Services
12345 Albert Hudon, Suite 100,
Montreal, Quebec, Canada H1G 3L1
Read Before Beginning Assembly
1-800-267-1739
Monday - Friday, 9:00 am - 5:00 pm (Eastern Time)
Warranty Information
2
Caution
DHP warrants this product to be free from defects in material and workmanship and
agrees to remedy any such defect. This warranty covers one year from the date of
original purchase. This is solely limited to the repair or replacement of defective
parts and assembly labor is not included.
This warranty does not apply to any product which has been improperly assembled,
subjected to misuse or abuse or which has been altered or repaired in any way.
Liability for consequential damages is excluded to the extent exclusion is permitted
by law. This warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
To obtain warranty service, purchaser must present original bill of sale. Components
repaired or replaced are warranted through the remainder of the original warranty
period only. The defective components will be repaired or replaced without charge,
subject to the terms and conditions described above.
Visit www.dhpfurniture.com to view the limited warranty valid in the U.S. and
Canada.
● Call our toll free number if you need assistance.
● Work in a spacious area and near where the unit will be used, preferably on a
carpet, or use a piece of the cardboard packaging to protect your floor and product.
● Recommended # of people needed for assembly: 2 (however it is always better
to have an extra hand). Estimated assembly time is 1 hours.
● Make sure all parts are included. Most parts are labeled or stamped on the raw
edge.
● Read each step carefully. It is very important that each step of the instructions is
performed in the correct order. If these steps are not followed in sequence,
assembly difficulties will occur.
● This product is designed for home use and not intended for commercial use.
● This product contains small components. Please ensure that they are kept away
from small children.
● Do not use power tools to assemble your furniture. Power tools may strip or
damage the parts.
For help with assembly, identifying parts, product information or to order parts,
please contact us:

3

4
Parts
All in 1 big box!
Before you throw the package, please use the
Check Box to identify the parts and ensure that
you have all the parts needed for the assembly.
There are inner box(es) that include components
required to complete this assembly.
Replacement Parts, Visit www.dhpfurniture.com/eng/support-home
A
Post
T933010
X 1
Side Rail
T938340
X 2
Side Rail
T938350
X 2
B
CD
G
T
Brace
T938360
X 1
Post
T933020
X 1
Post
T933030
X 1
End Guard Rail
T938650
X 2
Post
T933040
X 1
Brace
T938370
X 2
Brace
T938380
X 2
Slats
T930300
X 14
Leg
T937730
X 3
Leg
T937740
X 3
Bracket
T938310
X 1
Plastic Plug
T392590
X 28
H
I
PM
L
KY
Ball
T918200
X 4
A
S
T
S
B
E
F
P
S
C
T
D
E
F
M
SG
LK
I
H
Y
EF

5
Hardware Pack
Hardware Pack #: T3247298-02
Please do not completely tighten all the hardware,
until the entire assembly is complete, unless
otherwise indicated in the step-by-step
instructions.
The screw(s), bolt(s) to be used at each step are
shown in actual size in the lower right corner of
the page.
78
5
6
4
3
1
1/4" X 1 9/16"
X 4
1/4" X 7/8"
X 12
5/16" X 3/4"
X 16
1/4" X 11/16"
X 4
1/4"
X 4
4mm
X 1
Wrench
X 1
2
1/4" X 1 3/16"
X 8

6
Step 1
Insert T X 2 into A/B and C/D with ❷.
X 8
A
B
D
C
T
T
2
Correct: Part (T) penetrating
through Part (A,B,C&D).
Incorrect: Part (T) NOT
penetrating through Part (A,B,C&D).

7
Step 2
Insert F X 2 into E X 2 with ❺.
X 4
5
F
E
E
F

8
Step 3
3.1 Attach H X 2 to sub-assembly (E & F)
X 2 from previous step with ❸.
3.2 Attach G to E X 2 with ❸.
X 8
F
F
E
E
H
G
H3
3.1
3.2
FF
G
H

9
Step 4
This bed offers you 2 options for the height of
the bed foundation.
● To assembly in Higher Position:
From STEP 4 to STEP 9.
● To assembly in Lower Position:
From STEP 10 to STEP 15.
Attach M X 2 to G with ❸.
X 4
G
M
M
3
M
G
E
E
F
F

10
Step 5
Attach sub-assembly E/F from previous
step to A, B, C and D with ❹.
X 16
B
C
A
E
F
E
F
4
D
F
A
Wide side of the slot should
be facing up !

11
Step 6
6.1 Insert one end of both I into the slot on
G as illustrated.
6.2 Attach the other end of both I to H with
❶ and ❻.
X 2
6.1
6.2
I
I
G
H
X 2
1
6
I
II
H
G
1
6

12
Step 7
Attach M&K to G with ❶ and ❻.
X 2
G
M
K
X 2
6
1
G
M
K
1
6

13
Step 8
Insert P into E&F as illustrated, then lock P
into place with Y.
2
1
2
3
3
1
F
E
F
E
P
E
E
P
P
Y

14
Step 9
Attach S X 4 to A, B, C & D.
A
B
S
S
S
C
D
S
B

15
Step 10
X 4
3
G
L
L
● To assembly in Lower Position:
From STEP 10 to STEP 15.
Attach L X 2 to G with ❸.
G
L
F
F
E
E

16
Step 11
X 16
F
A
E
F
A
F
E
Attach sub-assembly E/F from previous
step to A, B, C and D with ❹.
4
B
C
D

17
Step 12
12.1
12.2
GII
H
I
I
I
G
H
X 2
X 2
12.1 Insert one end of both I into the slot
on G as illustrated.
12.2 Attach the other end of both I to H
with ❶ and ❻.
1
6
6
1

18
Step 13
L
L
G
K
1
6
G
I
K
X 2X 2
Attach L&K to G with ❶ and ❻.
1
6

19
Step 14
2
1
2
3
3
1
E
F
F
E
P
EE
PP
Y
YInsert P into E&F as illustrated, then lock P
into place with Y.

20
Step 15
A
B
C
D
Attach S X 4 to A, B, C & D.
S
S
S
S
B