DiaDent D.LUX+ User manual

Table of Contents
Table of Contents
1. Overview
2. Safety Instructions Device Storage
3. Package Contents
4. Product Description
5. Components Names
6. Operation Method
6.1 Preparation before use
6.2 Instruction for use and operation sequence
7. Hand-Piece Function and Set-up Method
7.1 Hand-piece function
7.2 Feature settings
7.3 Battery replacement
8. Charger Features and Cautions
8.1 Charger functions
8.2 Precautions during charging
9. Cleaning and Maintenance
9.1 Cleaning and maintenance
10. Disposal
11. Item Codes
12. Troubleshooting
13. Warranty
14. Technical Specification
15. Symbols
FCC Warning and EMC Information
Contact Information
5
6
8
9
9
10
11
11
12
12
12
12
13
14
15
15
16
16
17
18
19~21
21
ENGLISH


Overview
Overview


1. If the Light Probe is cracked or damaged, stop using it immediately. Being a plastic product
that may enter into mouth, the Light Probe can be hazardous.
2. Do not subject the handpieces to strong shocks or vibrations. Make sure that the Light Probe
is inserted securely and has not been pulled out before use (otherwise, it may cause
malfunctions or low light levels).
3. Never look directly at the output light. Otherwise, visual impairment may result.
4. As irradiating with strong light (in MAX mode) has a risk of burns, be careful when using it
and never use it continuously.
2. Safety Instructions
Safety Instructions
Safety Instructions
To reduce the risk of injury, always follow manufacturer’s cautions listed below as well as
other warnings and precautions throughout this manual.
CAUTION
Caution(s) indicates information, which could result in serious injury to the patient and/or the
operator and damage to the device, if not followed properly.
WARNING
1. The electromagnetic waves or other medical equipment in hospitals and clinics can cause
malfunction of this device.
2. Do not use this device on patients with pacemakers.
3. To reduce the risk of electric shock, do not try to open, disassemble or repair the hand-piece,
battery pack, or the charger base. Use only the charger and battery pack supplied by DiaDent.
4. Do not modify this equipment without authorization of the manufacturer.
5. Do not use this device in the presence of explosive and flammable materials to prevent
a possible explosion.
6. Use components/parts supplied by DiaDent only. Use of components/parts
manufactured by any other brand may cause damage or loss of performance and will thus void
the warranty.
GENERAL CAUTION
1.This device should be used exclusively by trained and certified dentists or endodontic specialists
for designated purposes described in this manual. If the device is used by any other users or
for purposes other than the designated purposes in this manual, the manufacturer bears
no liability due to injury from the incorrect usage.
2. Practice the technique and be familiar with the device before using on patients.
3. To prevent any possible injury, do not allow patients to handle or touch this device.
4. This product is not waterproof. Do not immerse the hand-piece, battery pack and charger base
in liquid of any kind.
5. For safe use, do not operate continuously in any mode and follow the specified duty cycle.
Application Notes


This product has been tested according to the IEC 60601-1-2 and is designed to provide reasonable
protection against harmful interference to general operation and installation of medical devices.
The device also has been designed and modified for professional health care enviroment
This product generates, uses, and can radiate radiofrequency energy and thus cause interference
to other devices nearby. In case of harmful interference, user is recommended to try one or more
of the following measures:
- Reorient or relocate the receiving device.
- Increase the separation distance between the interference-causing equipment and receiver.
- Consult a local dealer or the manufacturer.
- The battery of the device has passed both battery transportation test (UN DOT.38.3) and battery
stability test (IEC 62133)
Device Storage
ⓛ Store the device in a safe place with the following conditions to avoid device malfunction
or fire:
- Dry place where there is no moisture.
- Avoid leaving the device in a place with direct sunlight, or air with dust, salt, or sulfur.
- Atmospheric Pressure 70 ~ 106kPa / Temperature -10 ~ 40°C / Humidity 30 ~ 85%
② The device should be cleaned after each use.
③ Should there be any defects or malfunctions, stop using the device immediately and call
the customer service team.
④ Please turn off the device when it is not in use. In case the battery pack will not be used
for an extended period of time, unplug the adapter and make sure the battery pack is NOT
at a completely discharged state before storing the device.
Safety Instructions
5. Use disposable sheath to prevent contamination of the Light Probe and dispose it immediately
after use, as it is for single use only.
6. When moving the device, remove the hand-piece from the charger and move the hand-piece
with the light protector and the charger separately and safely. The light protector should be
attached to the hand-piece so it will not roll and lose balance when placed on a flat surface.
WARNING :
Portable RF communications equipment (including peripherals such as antenna cables and external
antennas) should be used no closer than 30 cm (12 inches) to any part of the , including
cables specified by the manufacturer. Otherwise, degradation of the performance of this equipment
could result.
Safety Instructions
If the device is not operated properly, it might be a malfunction due to static electricity. In this case,
press the power button for more than 6 seconds to turn it off and on.


Package Contents
Package Contents
3. Package Contents
Before removing the device from the box, check the items listed below and make sure you have
everything. If any item is missing or damaged, contact your sales representative immediately.
Contents:
•1x D-Lux+ Hand-piece
•1x D-Lux+ Charger
•1x Light Probe
•1x Light Protector
•1x C-Battery (Included in the hand-piece)
•1x Adapter
•1x Power Cord (1.5m or 1.8m)
•1x Disposable Sheaths (200 ea/Box)
•1x User Manual
Adapter Information
Manufacturer : EDAC Power Electronics Co., Ltd.
Model : EM1024A2
Input : 100-240V~, 1.0-0.5A, 50-60Hz
Output : 6V 2A
WARNING
Use of accessories, transducers and cables other than those specified or provided by the manufacturer
of this equipment could result in increased electromagnetic emissions or decreased electromagnetic
immunity of this equipment and result in improper operation.


Product Description
, the cordless LED visible light curing unit, has a stylish design and excellent
cooling performance. Having overcome the overheating problem (which may deteriorate LED
performance and even damage the unit) caused while using the visible light curing unit, it is
capable of reliably producing high power. With the application of dual wavelength LED, it is
capable of polymerizing various composite resins. Ergonomic design makes it convenient to
use. Built-in rechargeable battery, wireless battery charging method and absence of contact
terminal between the handpiece and the charger prevent the recharging part from contamination
and contact failure.
4. Product Description
5. Components Names
Various built-in protection circuits (overcharge and over-discharge protection circuits)
enable the device to be used safely. Battery level shown on the display window allows
operator to check the battery level status and to maintain a constant light output.
<Charger>
Charging / Intensity Indicator
(Charging / Light Intensity Status)
Built-in LED
Intensity Sensor
<Hand-piece>
Light Probe
Light Protector
Operation
Button
Display Window
Mode / Power
Button
Product Description


Operation Method
Operation Method
6.2 Instruction for use and operation sequence
1) Connect the adapter (power supply) of the charger to the power cord and then insert the
plug into the outlet.
2) Connect the charging jack to the charger.
3) Mount the handpiece on the charger to begin charging. The charging indicator on the charger
turns orange when the unit is charging and turns green when it is fully charged. It takes about
8 hours for the hand-piece to fully charge for the first time.
4) Insert the Light Probe into the hand-piece.
5) Attach the Light Protector to the hand-piece by pushing the Light Protector all the way down
the hand-piece until it cannot move down further.
6) Before using the unit, cover the Light Probe with the Disposable Sheath.
7) Press and hold the Mode (Power) button for about 2 seconds to turn on the power.
8) Press the Mode (Power) button for about 1 second to change the mode in the order of STD,
SFT, HIG, ORT and MAX in the display window. Press the Mode (Power) button briefly for
less than 1 second to change the set-up time
(For Mode and Time, see Section7.1 Hand-piece Function P.11)
9) Press the Operation button to perform light irradiation for the set time and press the button
once again to stop the light irradiation. The light irradiation progress time is displayed
numerically in the display window.
6.1 Preparation before Use
1) Be sure to read the instruction manual thoroughly before use.
2) Make sure the device is not damaged or defective before use.
3) Check the battery status before use.
4) Check each component such as hand-piece, battery, light probe, etc. before use.
5) Make sure all components are cleaned and disinfected before use.
6) Cover the Light Probe with disposable sheath before use.
6. Operation Method
* This is the Light Probe mounting part. It is removable.
Never look at the light output section without Light Protector.
It may cause visual impairment.
<Display> <Light Probe mounting part>
Light Probe
Battery Indicator Mode Operation Time (S)
The light probe is replaceable. To replace it, pull it out from the hand-piece.
Replace the Light Probe by inserting it into the hand-piece.
* Replace the Light Probe
*Make sure the light probe is as close to the area to be treated as possible. Be careful not to
shine the light onto close-by teeth and gums.


7.1 Hand-piece function
1) Press the Mode (Power) button for about 1 second to select the mode (5 different modes).
2) STD (Standard) mode irradiates with power of 900 mW/㎠ (±10%) for the selected time
(5, 10, 15 or 20 seconds).
3) SFT (Soft Start) mode starts irradiating slowly and gradually reaches a light intensity of
1,300 mW/㎠ (±10%) for the selected time (10 or 15 seconds).
4) HIG (High Power) mode irradiates with power of 1,300 mW/㎠ (±10%) for the selected time
(5, 10 or 15 seconds).
5) ORT (Orthodontic) mode irradiates with power of 1,800 mW/㎠ (±10%) for the selected time
(3, 4, 5 seconds or P). P (Pulse) : When the light is in ORT P (Pulse Mode), the light turns on
for 2 seconds and turns off for 1 second eight times.
6) MAX (Max Power) mode irradiates with power of 2,400 mW/㎠ (±10%) for the selected time
(1, 2 or 3 seconds).
7) Pressing the Operation Button during light irradiation stops the light irradiation immediately.
8) A flashing battery indicator shown on the Display Window while the unit is in use means that
it is running out of capacity and the low battery level may affect performance, limiting normal
operation. In order to restore normal function, it must be recharged immediately.
9) The device enters sleep mode after 5 minutes of inactivity with a buzzer sound and is
automatically turned off after 60 minutes.
7. Hand-piece Function and Set-up Method
Hand-piece Function and Set-up Method
Hand-piece Function and Set-up Method
10) Make sure to discard the Disposable Sheath after use.
11) After using the handpiece, please press and hold the Mode (Power) button for more than
2 seconds to turn off the power.
For safety, do not continuously operate in any mode and follow the specified duty cycle.