Dialog DA1458 Series User manual

Company confidential
User manual
DA1458x Production Line Tool
reference CLI
UM-B-008
Abstract
This document describes the reference command line interface (CLI) for the production test tool of
DA14580/581/583.

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
2 of 19
© 2015 Dialog Semiconductor GmbH
Contents
User manual......................................................................................................................................... 1
DA1458x Production Line Tool reference CLI.................................................................................. 1
UM-B-008.............................................................................................................................................. 1
Abstract................................................................................................................................................ 1
Contents............................................................................................................................................... 2
Tables ................................................................................................................................................... 3
1 Terms and definitions................................................................................................................... 3
2 References..................................................................................................................................... 3
3 Introduction.................................................................................................................................... 4
4 Getting started............................................................................................................................... 4
4.1 Precompiled binaries............................................................................................................. 4
4.2 Building the tool..................................................................................................................... 4
4.3 Building the firmware............................................................................................................. 4
5 General description....................................................................................................................... 5
6 Command line switches ............................................................................................................... 5
6.1 Switch –h............................................................................................................................... 5
6.2 Switch –p............................................................................................................................... 5
6.3 Switch –v............................................................................................................................... 5
7 Commands..................................................................................................................................... 6
7.1 cont_pkt_tx............................................................................................................................ 6
7.2 pkt_tx..................................................................................................................................... 6
7.3 start_pkt_rx ........................................................................................................................... 7
7.4 start_pkt_rx_stats.................................................................................................................. 7
7.5 stop_pkt_rx_stats.................................................................................................................. 7
7.6 stoptest.................................................................................................................................. 8
7.7 unmodulated TX.................................................................................................................... 8
7.8 unmodulated RX ................................................................................................................... 8
7.9 unmodulated OFF ................................................................................................................. 8
7.10 start_cont_tx.......................................................................................................................... 9
7.11 stop_cont_tx.......................................................................................................................... 9
7.12 reset ...................................................................................................................................... 9
7.13 xtrim rd .................................................................................................................................. 9
7.14 xtrim wr................................................................................................................................ 10
7.15 xtrim en................................................................................................................................ 10
7.16 xtrim dis............................................................................................................................... 10
7.17 xtrim inc............................................................................................................................... 11
7.18 xtrim dec.............................................................................................................................. 11
7.19 xtrim cal............................................................................................................................... 11
7.20 xtrim caltest......................................................................................................................... 12
7.21 sleep.................................................................................................................................... 12
7.22 otp wr_xtrim......................................................................................................................... 13
7.23 otp rd_xtrim ......................................................................................................................... 13
7.24 otp wr_bdaddr ..................................................................................................................... 13

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
3 of 19
© 2015 Dialog Semiconductor GmbH
7.25 otp re_xtrim ......................................................................................................................... 13
7.26 otp we_xtrim........................................................................................................................ 14
7.27 otp_read.............................................................................................................................. 14
7.28 otp_write.............................................................................................................................. 14
7.29 read_reg16.......................................................................................................................... 15
7.30 read_reg32.......................................................................................................................... 15
7.31 write_reg16 ......................................................................................................................... 15
7.32 write_reg32 ......................................................................................................................... 16
8 Return status codes.................................................................................................................... 17
9 Revision history .......................................................................................................................... 18
TablesTable 1: Power domain states for each sleep mode................................................................ 12
Table 2: Return codes ......................................................................................................................... 17
1 Terms and definitions
CLI Command Line Interface
GUI Graphical User Interface
HCI Host Controller Interface
OTP One Time Programmable
XTAL16M 16 MHz Crystal
XTAL32K 32 KHz Crystal
RC16M 16 MHz RC Oscillator
RC32K 32 KHz RC Oscillator
2 References
1. DA14580, Data sheet, Dialog Semiconductor
2. SPECIFICATION OF THE BLUETOOTH SYSTEM, version 4.0, Bluetooth SIG, 2010
3. Connection Manager, Help Document, Dialog Semiconductor
4. DA14581, Data sheet, Dialog Semiconductor

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
4 of 19
© 2015 Dialog Semiconductor GmbH
3 Introduction
This document describes the command line interface (CLI) for the production test tool of
DA14580/581/583.
The tool is a Microsoft Windows command line program that enables communication over UART with
a DA14580/581/583 device running the production test firmware.
The production test firmware is a special firmware that supports:
●The Bluetooth SIG standardised receiver and transmitter test HCI commands [2].
●Additional custom test HCI commands.
All test commands are also supported by the Connection Manager GUI application [3].
4 Getting started
4.1 Precompiled binaries
Precompiled binaries are provided for both the production test firmware and tool in the SDK:
●binaries\da1458x\prod_test\prod_test.hex for DA14580
binaries\da1458x\prod_test\prod_test_581.hex for DA14581
binaries\da1458x\prod_test\prod_test_583.hex for DA14583
●binaries\host\windows\prod_test_cmds\prodtest.exe
4.2 Building the tool
For SDK3.0.10.1 and earlier the tools are placed under: tools\prod_test\prod_test_cmds folder in
the SDK.
For SDK5.0.2.1 and later this is under: utilities\prod_test\prod_test_cmds
The next lines refer the SDK5.0.2 path using the utilities folder but it is the same in SDK3.0.10 in the
tools folder
Open utilities\prod_test\prod_test_cmds\prodtest.sln in “Microsoft Visual C++ 2010 Express”.
Make sure that the active solution configuration is the Release Configuration.
Build the project by selecting “Build –> Build Solution” in the menu.
The executable prodtest.exe is generated under the utilities\prod_test\prod_test_cmds\Release
folder.
4.3 Building the firmware
The required firmware is included in the SDK under the folder:
SDK5.0.2 and later: projects\target_apps\prod_test\prod_test
SDK3.0.10.1 and earlier: dk_apps\keil_projects\prod_test\prod_test
Steps for building the firmware
1. Open the \prod_test\prod_test\ folder.
2. Open the appropriate project depending on chip type and Keil μVision IDE version:
a. Keil 4:
DA14580: .\Keil_4\prod_test.uvproj
DA14581: .\Keil_4\prod_test_581.uvproj
DA14583: .\Keil_4\prod_test_583.uvproj
b. Keil 5:

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
5 of 19
© 2015 Dialog Semiconductor GmbH
DA14580: .\Keil_5\prod_test.uvprojx
DA14581: .\Keil_5\prod_test_581.uvprojx
DA14583: .\Keil_5\prod_test_583.uvprojx
3. Select menu “Project -> Rebuild all target files” to build the project.
4. Get the generated hex file from:
a. Keil 4:
DA14580: .\Keil_4\out\prod_test.hex
DA14581: .\Keil_4\out_581\prod_test_581.hex
DA14582: .\Keil_4\out_583\prod_test_583.hex
b. Keil 5:
DA14580: .\Keil_5\out\prod_test.hex
DA14581: .\Keil_5\out_581\prod_test_581.hex
DA14583: .\Keil_5\out_583\prod_test_583.hex
5 General description
The general syntax of the tool is:
prodtest <switches> <command> <command-arg-1> … <command-arg-2>
A command always returns a status code and optionally a list of return values. The return status
code and values are written to the standard output in a simple format: <value_name> = <value>.
The return status code is also returned as an exit code.
A zero status code represents the successful execution of a command. A non-zero status code
encodes the type of failure.
All other output of the tool is written to stderr (except the help message when –h option is used).
6 Command line switches
6.1 Switch –h
Description: print out all the commands of prodtest on a command line terminal
Usage: prodtest -h
6.2 Switch –p
Description: select the COM port number on a PC. All commands require this switch.
Usage: prodtest –p <COM_PORT_NUMBER> ….
6.3 Switch –v
Description: display the tool’s version
Usage: prodtest –v

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
6 of 19
© 2015 Dialog Semiconductor GmbH
7 Commands
7.1 cont_pkt_tx
Description: this is the Bluetooth SIG standardized [2] HCI_LE_Transmitter_Test command. It
continuously transmits packets until the stoptest command is executed.
Syntax: prodtest –p <COM_PORT_NUMBER> cont_pkt_tx <FREQUENCY> <DATA_LENGTH>
<PAYLOAD_TYPE>
Parameters:
●FREQUENCY is an even integer between 2402 and 2480. E.g. integer 2480 corresponds to
2.480 GHz.
●DATA_LENGTH is the payload length in bytes (a number between 1 and 37).
●PAYLOAD_TYPE must have one of the following values:
0: Pseudo-Random bit sequence 9
1: Pattern of alternating bits ‘11110000’
2: Pattern of alternating bits ‘10101010’
3: Pseudo-Random bit sequence 15
4: Pattern of All ‘1’ bits
5: Pattern of All ‘0’ bits
6: Pattern of alternating bits ‘00001111’
7: Pattern of alternating bits ‘0101’
Example:
prodtest -p 14 cont_pkt_tx 2402 35 6
Output example:
status = 0
7.2 pkt_tx
Description: transmit the specified number of packets.
Syntax: prodtest –p <COM_PORT_NUMBER> pkt_tx <FREQUENCY> <DATA_LENGTH>
<PAYLOAD_TYPE> <NUMBER_OF_PACKETS>
Parameters:
●FREQUENCY is an even integer between 2402 and 2480. E.g. 2480 corresponds 2.480 GHz.
●DATA_LENGTH is the payload length in bytes (a number between 1 and 37).
●PAYLOAD_TYPE must have one of the following values:
0 : Pseudo-Random bit sequence 9
1 : Pattern of alternating bits ‘11110000
2 : Pattern of alternating bits ‘10101010’
3 : Pseudo-Random bit sequence 15
4 : Pattern of All ‘1’ bits
5 : Pattern of All ‘0’ bits
6 : Pattern of alternating bits ‘00001111
7 : Pattern of alternating bits ‘0101’
●NUMBER_OF_PACKETS is an integer between 1 and 65535.
Example: the following command sends 1000 packets
prodtest -p 14 pkt_tx 2402 35 6 1000

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
7 of 19
© 2015 Dialog Semiconductor GmbH
Output example:
status = 0
7.3 start_pkt_rx
Description: This is the Bluetooth SIG standardized [2] HCI_LE_Receiver_Test command. It
continuously receives packets until the stoptest command is executed.
Syntax: prodtest –p <COM_PORT_NUMBER> start_pkt_rx <FREQUENCY>
Parameters:
●FREQUENCY is an even integer between 2402 and 2480. E.g. 2480 corresponds 2.480 GHz.
Example:
prodtest –p 14 start_pkt_rx 2402
Output example:
status = 0
7.4 start_pkt_rx_stats
Description: starts packet RX with additional statistics. It continuously receives packets until the
stop_pkt_rx_stats command is executed.
Syntax: prodtest –p <COM_PORT_NUMBER> start_pkt_rx_stats <FREQUENCY>
Parameters:
●FREQUENCY is an even integer between 2402 and 2480. E.g. 2480 corresponds 2.480 GHz.
Example:
prodtest –p 14 start_pkt_rx_stats 2402
Output example:
status = 0
7.5 stop_pkt_rx_stats
Description: ends packet RX with additional statistics and reports the following statistics:
●number of packets received correctly (nb_packets_received_correctly)
●number of packets with sync error (nb_packets_with_syncerror)
●number of packets with CRC error (nb_packets_received_with_crcerr)
●RSSI in dBm (rssi)
Syntax: prodtest –p <COM_PORT_NUMBER> stop_pkt_rx_stats
Example:
prodtest –p 14 stop_pkt_rx_stats
Output example:
status = 0
nb_packets_received_correctly = 8529
nb_packets_with_syncerror = 0
nb_packets_received_with_crcerr = 1
rssi = -37.30

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
8 of 19
© 2015 Dialog Semiconductor GmbH
7.6 stoptest
Description: This is the Bluetooth SIG standardized [2] HCI_LE_Test_End command. It is used:
●after a cont_pkt_tx command to end the standard packet TX test mode.
●after a start_pkt_rx command to end the standard packet RX mode and report the number of
received packets.
Syntax: prodtest –p <COM_PORT_NUMBER> stoptest
Example:
prodtest –p 14 stoptest
Output example (the number of packets is always zero when executed after a cont_pkt_tx):
status = 0
number_of_packets = 0
Output example (when executed after a start_pkt_rx):
status = 0
number_of_packets = 4360
7.7 unmodulated TX
Description: starts a Continuous Wave (CW) or unmodulated TX test.
Syntax: prodtest –p <COM_PORT_NUMBER> unmodulated TX <FREQUENCY>
Parameters:
●FREQUENCY is an even integer between 2402 and 2480. E.g. 2480 corresponds 2.480 GHz.
Example:
prodtest -p 14 unmodulated TX 2404
Output example:
status = 0
7.8 unmodulated RX
Description: starts the unmodulated RX test.
Syntax: prodtest –p <COM_PORT_NUMBER> unmodulated RX <FREQUENCY>
Parameters:
●FREQUENCY is an even integer between 2402 and 2480. E.g. 2480 corresponds 2.480 GHz.
Example:
prodtest -p 14 unmodulated RX 2404
Output example:
status = 0
7.9 unmodulated OFF
Description: stops unmodulated TX or RX test.
Syntax: prodtest –p <COM_PORT_NUMBER> unmodulated OFF
Example:
prodtest -p 14 unmodulated OFF
Output example:

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
9 of 19
© 2015 Dialog Semiconductor GmbH
status = 0
7.10 start_cont_tx
Description: starts the continuous TX test mode. It transmits continuously a modulated signal until
the stop_cont_tx command is executed.
Syntax: prodtest –p <COM_PORT_NUMBER> start_cont_tx <FREQUENCY> <PAYLOAD_TYPE>
Parameters:
●FREQUENCY is an even integer between 2402 and 2480. E.g. 2480 corresponds 2.480 GHz.
●PAYLOAD_TYPE must have one of the following values:
0 : Pseudo-Random bit sequence 9
1 : Pattern of alternating bits ‘11110000’
2 : Pattern of alternating bits ‘10101010’
3 : Pseudo-Random bit sequence 15
4 : Pattern of All ‘1’ bits
5 : Pattern of All ‘0’ bits
6 : Pattern of alternating bits ‘00001111’
7 : Pattern of alternating bits ‘0101’
Example:
prodtest –p 14 start_cont_tx 2404 4
Output example:
status = 0
7.11 stop_cont_tx
Description: stops the continuous TX test mode.
Syntax: prodtest –p <COM_PORT_NUMBER> stop_cont_tx
Example:
prodtest –p 14 stop_cont_tx
Output example:
status = 0
7.12 reset
Description: this is the Bluetooth SIG standardized [2] HCI_Reset command.
Syntax: prodtest –p <COM_PORT_NUMBER> reset
Example:
prodtest –p 14 reset
Output example:
status = 0
7.13 xtrim rd
Description: reads the value of the XTAL16M trimming register as specified in DA14580 datasheet
[1] section 5: CLK_FREQ_TRIM_REG (0x50000002).
The value is reported in decimal format.
Syntax: prodtest -p <COM port number> xtrim rd

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
10 of 19
© 2015 Dialog Semiconductor GmbH
Example:
prodtest –p 14 xtrim rd
Output example:
status = 0
trim_value = 500
7.14 xtrim wr
Description: writes a value into the XTAL16M trimming register. The new value is written
immediately and it is already effective when the prodtest program finishes executing this command.
Syntax: prodtest -p <COM port number> xtrim wr <trim_value>
Parameters:
●trim_value is the unsigned 16-bit decimal value to be written into the XTAL16M trimming register.
Example:
prodtest –p 14 xtrim wr 500
Output example:
status = 0
7.15 xtrim en
Description: enables XTAL16M output on GPIO P0_5. The command takes effect immediately.
Syntax: prodtest -p <COM port number> xtrim en
Example:
prodtest –p 14 xtrim en
Output example:
status = 0
Note 1 This command can also be used to enable the 32kHz clock on a GPIO 0_6. To do this two additional
registers need to be set using the write_reg16 command (see section 7.31)
Enable 32kHz clock in CLK_32K_REG, set bit 0 and bit 7 to ‘1’
Set GPIO P0_6 to output mode. In P06_MODE_REG, set bit 8 and 9 to ‘1’
Example:
prodtest –p 14 write_reg16 50000020 079D
prodtest –p 14 write_reg16 50003012 0300
Output example:
status = 0
7.16 xtrim dis
Description: disables XTAL16M output on GPIO P0_5. The command takes effect immediately.
Note 2 This command also disables:
XTAL32K output on GPIO P0_6
RC16M output on P0_7
RC32K output on P1_0
Syntax: prodtest -p <COM port number> xtrim dis
Example:
prodtest –p 14 xtrim dis

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
11 of 19
© 2015 Dialog Semiconductor GmbH
Output example:
status = 0
7.17 xtrim inc
Description: increments the XTAL16M trimming register. The register’s new value is already
effective when the prodtest program finishes executing this command.
Syntax: prodtest -p <COM port number> xtrim inc <delta>
Parameters:
●delta is the unsigned 16-bit decimal value to be added to the XTAL16M trimming register.
Example:
prodtest –p 14 xtrim inc 5
Output example:
status = 0
7.18 xtrim dec
Description: decrements the XTAL16M trimming register. The register’s new value is already
effective when the prodtest program finishes executing this command.
Syntax: prodtest -p <COM port number> xtrim dec <delta>
Parameters:
●delta is the unsigned 16-bit decimal value to be subtracted from the XTAL16M trimming register.
Example:
prodtest –p 14 xtrim dec 5
Output example:
status = 0
7.19 xtrim cal
Description: runs the XTAL16M trimming register calibration procedure which uses an externally
applied 500ms high square pulse as a reference for trim value calibration. The procedure executes
the following steps:
1. Calibrates the XTAL16M trimming register.
2. Programs the calibrated value in OTP (at address 0x7F8C).
3. Enables the “XTAL16M trim value is valid” bit in OTP (at address 0x7F78).
If a square pulse has not been applied on the given GPIO then the calibration procedure will fail with
a status code equal to 27.
Syntax: prodtest -p <COM port number> xtrim cal <Px_y>
Parameters:
●Px_y is the GPIO that the external square pulse is applied on.
Example:
prodtest –p 14 xtrim cal P1_0
Output example:
status = 0

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
12 of 19
© 2015 Dialog Semiconductor GmbH
7.20 xtrim caltest
Description: behaves identically to “xtrim cal” with the exception that it does not modify the OTP.
Syntax: prodtest -p <COM port number> xtrim caltest <Px_y>
Parameters:
●Px_y is the GPIO that the external square pulse is applied on.
Example:
prodtest –p 14 xtrim caltest P1_0
Output example:
status = 0
7.21 sleep
Description: puts the device to sleep for a specified number of minutes and seconds.
Syntax: prodtest –p <COM_PORT_NUMBER> sleep <mode> <minutes> <seconds>
Parameters:
●mode is one of the available sleep modes defined in section 3.5 of the datasheet [1]:
○none = Sleep Mode (no power gating, ARM CPU is idle waiting for an interrupt)
○extended = Extended Sleep Mode
○deep = Deep Sleep Mode
●minutes is a number between 0 and 255.
●seconds is a number between 0 and 255.
If both minutes and seconds are set to zero then the device sleeps forever.
The active peripherals in each sleep mode are shown in table 1.
Table 1: Power domain states for each sleep mode
Power
mode
PD_SYS (
AHB, OTP,
ROM,
Watchdog,
SW timer,
GPIO
multiplexing)
PD_PER
(UARTs,
SPI, I2C,
Keyboard
controller,
ADC)
PD_DBG
PD_RAD
(Radio and
BLE core)
PD_RRx
(Retention
RAM x)
PD_SR
(System
RAM)
Analog
(BandGap,
DCDC
converter
XTAL16M,
RC
oscillators,
ADC,
LDOs)
Sleep
Mode
ON
ON
ON
ON
ON
ON
ON
Extended
Sleep
Mode
OFF
Programmed
to OFF
OFF
Programmed
to OFF
Programmed
to ON
ON
OFF
Deep
Sleep
Mode
OFF
Programmed
to OFF
OFF
Programmed
to OFF
Programmed
to ON
OFF
OFF
Known limitations:
●UART communication is lost when the device wakes up from extended sleep mode.
●The device will not wake up from deep sleep mode.
Example 1:
prodtest –p 14 sleep none 1 0

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
13 of 19
© 2015 Dialog Semiconductor GmbH
Example 2:
prodtest –p 14 sleep extended 0 30
Example 3:
prodtest –p 14 sleep deep 0 0
Output example:
status = 0
7.22 otp wr_xtrim
Description: writes the XTAL16M trim value into the OTP header.
Syntax: prodtest -p <COM port number> otp wr_xtrim <decimal trim value>
Parameters:
●decimal trim value is the unsigned 16-bit decimal XTAL16M trim value to be written into the OTP
header.
Example:
prodtest –p 14 otp wr_xtrim 500
Output example:
status = 0
7.23 otp rd_xtrim
Description: reads the XTAL16M trim value from the OTP header. The output value is in decimal
format.
Syntax: prodtest -p <COM port number> otp rd_xtrim
Example:
prodtest –p 14 otp rd_xtrim
Output example:
status = 0
otp_xtrim_value = 500
7.24 otp wr_bdaddr
Description: writes the Bluetooth Device address into the OTP header.
Syntax: prodtest -p <COM port number> otp wr_bdaddr <BD address>
Parameters:
●BD address is the Bluetooth Device address to be written into the OTP header. The BD address
must be formatted as XX:XX:XX:XX:XX:XX where X is a hexadecimal digit.
Example:
prodtest –p 14 otp wr_bdaddr 44:49:41:4c:4f:47
Output example:
status = 0
7.25 otp re_xtrim
Description: reads the XTAL16M calibration flag from the OTP header (bit 4 of the calibration flag in
OTP header).
Syntax: prodtest -p <COM port number> otp re_xtrim

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
14 of 19
© 2015 Dialog Semiconductor GmbH
Example:
prodtest –p 14 otp re_xtrim
Output example:
status = 0
otp_xtrim_enabled = 1
7.26 otp we_xtrim
Description: enables the XTAL16M calibration flag from the OTP header by modifying the bit 4 of
the calibration flag in OTP header from 0 to 1.
Syntax: prodtest –p <COM port number> otp we_xtrim
Example:
prodtest –p 14 otp we_xtrim
Output example:
status = 0
7.27 otp_read
Description: reads consecutive words from OTP memory.
Syntax: prodtest -p <COM port number> otp_read <otp address> <word count>
Parameters:
●otp address is the start address of the OTP memory region to be read. This is a word address
hence it must be divisible by 4. It must be lower than 0x8000. It must be formatted as a 16 bit
hexadecimal number.
●Word count is the number of words to be read. The accepted range is from 1 to 60. The word
count must satisfy the formula: <otp address> + 4 * <word count> <= 0x8000. It must be
formatted as a decimal number.
Example:
prodtest -p 16 otp_read 7FDC 5
Output example:
status = 0
[7FDC] = 1234A5A5
[7FE0] = A5A51234
[7FE4] = 14121117
[7FE8] = 24222127
[7FEC] = 00000007
7.28 otp_write
Description: writes consecutive words into OTP memory.
Syntax: prodtest -p <COM port number> otp_write <otp address> <word #1> … <word #n>
Parameters:
●otp address is the start address of the OTP memory region to be written. This is a word address
hence it must be divisible by 4. It must be lower than 0x8000. It must be formatted as a 16 bit
hexadecimal number.

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
15 of 19
© 2015 Dialog Semiconductor GmbH
●Word #i is the word value to be written in address: <otp address> + 4 * i. It must be formatted as
a 32 bit hexadecimal number. The number of word value arguments must be at most 60 and
must satisfy the formula: <otp address> + 4 * n <= 0x8000.
Example:
prodtest -p 16 otp_write 7FDC 1234A5A5 A5A51234
Output example:
status = 0
7.29 read_reg16
Description: reads the value of a 16-bit register. The output value is printed in hex.
Syntax: prodtest -p <COM port number> read_reg16 <register address>
Parameters:
●register address is the address of the 16-bit register to be read. The register address must be
half-word aligned hence it must be divisible by 2. It must be formatted as a 32-bit hexadecimal
number.
Example: the following command reads TRIM_CTRL_REG (0x50000016) [1].
prodtest -p 16 read_reg16 50000016
Output example:
status = 0
value = 00A2
7.30 read_reg32
Description: reads the value of a 32-bit register. The output value is printed in hex.
Syntax: prodtest -p <COM port number> read_reg32 <register address>
Parameters:
●register address is the address of the 32-bit register to be read. The register address must be
word aligned hence it must be divisible by 4. It must be formatted as a 32-bit hexadecimal
number.
Example: the following command reads PATCH_VALID_REG (0x40008400) [1].
prodtest -p 16 read_reg32 40008400
Output example:
status = 0
value = 00000001
7.31 write_reg16
Description: writes into a 16-bit register.
Syntax: prodtest -p <COM port number> write_reg16 <register address> <register value>
Parameters:
●register address is the address of the 16-bit register to be read. The register address must be
half-word aligned hence it must be divisible by 2. It must be formatted as a 32-bit hexadecimal
number.
●register value is the value to be written into the register. It must be formatted as a 16-bit
hexadecimal number.
Example: the following command writes 0x00B3 in TRIM_CTRL_REG (0x50000016) [1].

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
16 of 19
© 2015 Dialog Semiconductor GmbH
prodtest -p 16 write_reg16 50000016 00B3
Output example:
status = 0
7.32 write_reg32
Description: writes into a 32-bit register.
Syntax: prodtest -p <COM port number> write_reg32 <register address> <register value>
Parameters:
●register address is the address of the 32-bit register to be read. The register address must be
word aligned hence it must be divisible by 4. It must be formatted as a 32-bit hexadecimal
number.
●register value is the value to be written into the register. It must be formatted as a 32-bit
hexadecimal number.
Example: the following command writes 0x0000000F in PATCH_VALID_REG (0x40008400) [1].
prodtest -p 16 write_reg32 40008400 0000000F
Output example:
status = 0

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
17 of 19
© 2015 Dialog Semiconductor GmbH
8 Return status codes
Following table summarizes the return codes of the productions test tool
Table 2: Return codes
Status code
Description
0
SC_NO_ERROR
1
SC_MISSING_COMMAND
2
SC_INVALID_COMMAND
3
SC_WRONG_NUMBER_OF_ARGUMENTS
4
SC_INVALID_COM_PORT_NUMBER
5
SC_INVALID_FREQUENCY_ARG
6
SC_INVALID_DATA_LENGTH_ARG
7
SC_INVALID_PAYLOAD_TYPE_ARG
8
SC_COM_PORT_INIT_ERROR
9
SC_RX_TIMEOUT
10
SC_UNEXPECTED_EVENT
11
SC_INVALID_NUMBER_OF_PACKETS_ARG
12
SC_INVALID_UNMODULATED_CMD_MODE_ARG
13
SC_COM_PORT_NOT_SPECIFIED
14
SC_INVALID_SLEEP_CMD_MODE_ARG
15
SC_INVALID_SLEEP_CMD_MINUTES_ARG
16
SC_INVALID_SLEEP_CMD_SECONDS_ARG
17
SC_INVALID_XTAL_TRIMMING_CMD_OPERATION_ARG
18
SC_INVALID_XTAL_TRIMMING_CMD_TRIM_VALUE_ARG
19
SC_INVALID_OTP_CMD_OPERATION_ARG
20
SC_INVALID_OTP_CMD_TRIM_VALUE_ARG
21
SC_INVALID_OTP_CMD_BDADDR_ARG
22
SC_INVALID_OTP_ADDRESS_ARG
23
SC_INVALID_NUMBER_OF_OTP_WORDS_ARG
24
SC_INVALID_WORD_VALUE_ARG
25
SC_INVALID_GPIO_ARG
26
SC_XTAL_TRIMMING_CAL_OUT_OF_RANGE_ERROR
27
SC_XTAL_TRIMMING_CAL_FREQ_NOT_CONNECTED
28
SC_INVALID_REGISTER_ADDRESS_ARG
29
SC_INVALID_REGISTER_VALUE_ARG
1000 –1063
SC_HCI_STANDARD_ERROR_CODE_BASE (1000) + standard HCI error code

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
18 of 19
© 2015 Dialog Semiconductor GmbH
9 Revision history
Revision
Date
Description
1.0
24-Mar-2014
Initial version for DA14580-01
1.1
17-Apr-2014
Addition of commands for reading/writing XTAL16M trim value and BD
address from OTP
1.2
22-Apr-2014
Addition of commands for enabling XTAL16M calibration flag and
reading XTAL16M calibration flag
1.3
05-May-2014
Modification of “otp re_xtrim” command’s output.
1.4
16-May-2014
Addition of otp_read, otp_write_commands.
1.5
20-Jun-2014
Addition of read_reg16, read_reg32, write_reg16, write_reg32, “xtrim
cal” and “xtrim caltest” commands.
1.6
06-Mar-2015
Updated for DA14581. Added –v switch. Updated paths for SDK v3.0.8.
The “xtrim cal” and “xtrim caltest” commands detect if the square wave
pulse is absent.
1.7
18-Nov-2015
Updated for the SDK 3.0.10 and SDK5.0.2 release.
Added the description how to enable XTAL32 on a GPIO

UM-B-008
DA1458x Production Line Tool reference CLI
Company confidential
User manual
Revision 1.7
18-Nov-2015
CFR0012-00 Rev 1
19 of 19
© 2015 Dialog Semiconductor GmbH
Status definitions
Status
Definition
DRAFT
The content of this document is under review and subject to formal approval, which may result in
modifications or additions.
APPROVED
or unmarked
The content of this document has been approved for publication.
Disclaimer
Information in this document is believed to be accurate and reliable. However, Dialog Semiconductor does not give any
representations or warranties, expressed or implied, as to the accuracy or completeness of such information. Dialog
Semiconductor furthermore takes no responsibility whatsoever for the content in this document if provided by any information
source outside of Dialog Semiconductor.
Dialog Semiconductor reserves the right to change without notice the information published in this document, including without
limitation the specification and the design of the related semiconductor products, software and applications.
Applications, software, and semiconductor products described in this document are for illustrative purposes only. Dialog
Semiconductor makes no representation or warranty that such applications, software and semiconductor products will be
suitable for the specified use without further testing or modification. Unless otherwise agreed in writing, such testing or
modification is the sole responsibility of the customer and Dialog Semiconductor excludes all liability in this respect.
Customer notes that nothing in this document may be construed as a license for customer to use the Dialog Semiconductor
products, software and applications referred to in this document. Such license must be separately sought by customer with
Dialog Semiconductor.
All use of Dialog Semiconductor products, software and applications referred to in this document are subject to Dialog
Semiconductor’s Standard Terms and Conditions of Sale, unless otherwise stated.
© Dialog Semiconductor GmbH. All rights reserved.
RoHS Compliance
Dialog Semiconductor complies to European Directive 2001/95/EC and from 2 January 2013 onwards to European Directive
2011/65/EU concerning Restriction of Hazardous Substances (RoHS/RoHS2).
Dialog Semiconductor’s statement on RoHS can be found on the customer portal https://support.diasemi.com/. RoHS
certificates from our suppliers are available on request.
Contacting Dialog Semiconductor
Germany Headquarters
Dialog Semiconductor GmbH
Phone: [phone]
United Kingdom
Dialog Semiconductor (UK) Ltd
Phone: [phone]
The Netherlands
Dialog Semiconductor B.V.
Phone: [phone]
North America
Dialog Semiconductor Inc.
Phone: [phone]
Japan
Dialog Semiconductor K. K.
Phone: [phone]
Taiwan
Dialog Semiconductor Taiwan
Phone: [phone]
Singapore
Dialog Semiconductor Singapore
Phone: [phone]
China
Dialog Semiconductor China
Phone: [phone]
Korea
Dialog Semiconductor Korea
Phone: [phone]
Email:
[email protected]
Web site:
www.dialog-semiconductor.com