Diamond Antenna SDC1 User manual

<<Attention>>
●Do not install the product where is got the direct
rays of the sun. Do not install the product near
the jet of the air conditioner. It may cause to
have a fire, transform, discolor or damage.
●Do not wipe it off with thinner or benzene. If it
becomes too dirty, wipe it off the neuter
detergent.
●Do not install the product where there is much
moisture or dust. It may cause to have a fire,
generate heat, electrify or damage.
●For the safety, be sure to cut off the power
supply when it is not used.
●Do not put something heavy on the product.
●Use the product under rated specification only.
●Do not use the product when driving a car.
Serious accidents could have been happened.
・Specification
Frequency: 3.5/7/10/14/18/21/24
/28(29)/50MHz Band
Operation time:
3.5MHz→HOM→3.5MHz approx. 160 sec.
7MHz→HOM→7MHz approx. 50 sec.
14MHz→HOM→14MHz approx. 20 sec.
*HOM –Operation standard position
(Lowest position of the coil)
Power supply voltage & current:
DC12V (9-14.5V) 200mA
Dimensions: 85(W)x 120(D)x 32(H)mm
Weight: 380g
<<Note>>
●Power supply voltage of the SDC1 is DC12V
(9-14.5V usable). Please use it with the
prescribed voltage.
●If the polarity of the power supply is wrong, the
power supply is not going to turn ON because of
a safety circuit.
●The fuse of the cigar plug is 2A. When changing
the plugs, please use the prescribed standard
one.
●Do not push more than two buttons at the same
time. Do not tune the frequency change dial
during moving the coil. It may cause
malfunction and the antenna may be damaged.
●The controller cannot be auto-tuning. The fine
tuning by manual operation is required.
SDC1
Operation Instructions
SD1 is a tuning controller for the SD330 screw
driver antenna.
To use the product properly, read these
instructions thoroughly before using it. Keep this
manual carefully at hand for later use. The manual
will be changed in the future without advance
notice.
<<Warning>>
●Do not use the product under unusual
conditions. Do not use the product when
unusual conditions happen such as smoking,
unusual smell or sound. Keeping using the
product under those situations may cause to
electrify or damage. Ask the dealer to repair it.
Do not repair it by yourself because it is
dangerous.
●Do not overhaul or reconstruct the product. It
may cause to have a fire, electrify or damage.
●Do not put wire, metal or substance into the
product. It may cause to have a fire, electrify or
damage.
●Do not use the product at the place where
inflammability gas is generated. It may cause to
have a fire or explode.
●Do not use the product except for the
specification of the operation instructions. It
may cause to have a fire, or electrify.
●Do not damage, process, bend, twist or put the
power supply cord. Do not put something heavy
on the product or heat it up. Breaking the cord
may cause to have a fire, electrify or damage.
●Do not use the product when cigarette lighter is
inserted loosely. It may cause to have a fire,
electrify or damage.
●Do not touch the power supply plug or the
product with wet hands.
●Do not use the product where is easily
reachable by babies and children. It may cause
to electrify or do themselves an injury.
●Do not soak the product in water. Do not get wet
the product. It may cause to have a fire, electrify
or damage.
●Do not drop the product. Do not give them big
impact.
Tuning Controller for SD330

3.5
7
10
14
18
21
24
28
50
off
7MHz TUNING
7MHz = 1249
1200 800
POWER
SD330 CONTROLLER
RESET
DOWN
SDC1
FREQ
GO
UP
1
2
3
45
6
7
9
8
To cigar socket
To the SD330 Antenna
SD330 Antenna
(not included)
DIAMONDANTENNACORPORATION
MiyataBuilding,No.15-1,1-chomeSugamo,ToshimakuTokyo,Japan170-0002TEL.[phone]FAX.[phone]
HomePagehttp://www.diamond-ant.co.jp
E-mail[email protected]
The included cable
of the SD330
(not included)
core
・How to use the SDC1
1, Connect it as shown in below. Plug the cigar plug
into a cigar socket.
2, To turn the power switch ON, LED lamp turns on
and the current operation situation is shown on
the display panel.
3, Turn the frequency change dial and set the
operation frequency.
4, When pushing the GO button, the frequency and
“GO HOM POSITION” will be shown in the
display panel and the coil will be moved to the
lowest position. After that, the coil will be moved
to the selected frequency. The frequency and
position count number will be shown at that time.
5, When the coil goes to the selected frequency, the
coil will be stopped automatically. After stopping
the coil, please transmit at less than the output
10W. Adjust the SWR by UP/DOWN buttons.
(Since the antenna’s conditions will be changed
depending on the surrounding condition, weather
and installation place. Please make sure to
check SWR.
6, To keep pushing the UP button, the coil will be
moved to the highest position and be stopped
moving. Since the internal motor will keep truing,
stop pushing the UP button at the earliest. After
that, to push the RESET button and push the GO
button, the coil will be moved to the selected
frequency.
7, If you want to stop the coil during operation, push
the RESET button. The coil will be stopped at the
position.
8, When you want to re-start the UP/DOWN
movement, go back to 3 or push UP/DOWN
buttons. The coil will be moved.
9, When operating 50MHz band, use the optional
element “OPE750”.
●The SDC1 is not the water proof structure. Do
not get water to the product.
●Since the inside of the SDC1 is a complicated
electronic circuit, don’t use it where is a strong
magnetic field or high temperature and
humidity.
●Since the dashboard of the car becomes high
temperature, don’t install the product at the
dashboard.
・Descriptions and Functions
①Display panel: The operation situation is shown.
②Frequency change dial: To change the
operation frequency.
③GO button: To start the operation.
④UP button: To go the coil up. (To tune lower
frequency)
⑤DOWN button: To go the coil down. (To tune
higher frequency)
⑥RESET button: To stop the coil during moving
the coil.
⑦Power switch: To turn ON/OFF.
⑧Cigar plug: To connect with a cigar socket of a
car and to take power supply.
⑨Terminal for connection with the SD330: (The
terminal is different depending on the
production time. Please connect with a suitable
one.
・Wiring and Connection