Digiever DS-16300-RM Pro+ Series User manual

1
Network Video Recorder
Quick Installation Guide
DS-16300-RM UHD Series
DS-16316-RM UHD/DS-16320-RM UHD/
DS-16324-RM UHD/DS-16328-RM UHD/
DS-16332-RM UHD/DS-16336-RM UHD/
DS-16340-RM UHD/DS-16348-RM UHD/
DS-16356-RM UHD/DS-16364-RM UHD
Quality Service Group
2.0.0.2
Information in this document is subject to change without notice.
© Copyright 2022, DIGIEVER Corporation. All rights reserved.

1
Quick Installation Guide
Thank you for choosing DIGIEVER Network Video Recorder. The following
quick guide will lead you to complete the installation and configuration of the
NVR. Please read the following description carefully.
Pre-installation Notice
The following safety precautions will increase the life of the NVR. Follow all
precautions and instructions.
Electrical Safety
Unplug this product from the power source before cleaning.
Use only the bundled power adapter. Using other power adapters may damage
your device.
Ensure that you plug the power adapter to the correct power input rating. Check
the label on the power adapter for the power rating.
Caution: Power cord(s) must be plugged into a socket-outlet with earthing
connection.
Operation Safety
DO NOT place this product in a location where it may get wet.
Place this product on a flat and stable surface.
Use this product in environments with an ambient temperature between 0°C and
45°C.
DO NOT block the air vents on the case of this product. Always provide proper
ventilation for this product.
DO NOT insert any object or spill liquid into the air vents. If you encounter
technical problems with this product, contact a qualified service technician or
your retailer. DO NOT attempt to repair this product yourself.
Caution: There is a risk of explosion if the battery is replaced with an incorrect
type. Dispose of used batteries appropriately.
Caution: Slide-rail-mounted equipment is not to be used as a shelf or a work
space.

2
Pre-installation Notice
Please make sure the following items are prepared for installing DIGIEVER
NVR DS-16300-RM UHD Series.
Network connection
Configuration of network cameras
Compatibility of network cameras
Computer for configuring DIGIEVER NVR
1-16 hard disks
Compatibility of hard disk with DIGIEVER NVR
1 slotted screwdriver and 1 Philips screwdriver
*For camera compatibility, please check our website
http://www.digiever.com/support/compatibility.php
Remote PC System Requirements
The following are minimum system requirements for a personal computer to
operate the DIGIEVER in better performance:
Operating System
Microsoft®Windows®Vista/7/8/10/11 (32 and 64-bit)
Browsers (32-bit) in Windows OS
Microsoft® Internet Explorer 10.0 or above, Chrome 56.0.29 or above,
Firefox 51.0.1 or above, Opera 43.0.2 or above
CPU
For channels under 16: Intel® Dual core CPU 3.0 GHz or above
For channels over 16: Intel®i5/i7 CPU 3.3 GHz or above
Network
Minimum 10/100/1000 Ethernet (Gigabit Ethernet is recommended)
Note: * User is suggested to connect cameras and NVR with
Gigabit switch.
Memory
For channels under 16: DDR3 4G or above
For channels over 16: IDDR3 8G or above
Graphics Adapter
AGP or PCI-Express, minimum 1024×768, 16bit colors, 1G memory or
above
Note: It is highly recommended to use a graphics adaptor which
provides higher than resolutions 1024 x 768 in order to experience

3
the full benefits of the software.
Make sure the display DPI setting is set to default at 96DPI
To set DPI value, right-click on desktop, choose “Settings” tab
>> “Advanced” >> “General.”
CD-ROM Drive
It is necessary to read the operating instructions in the provided CD-
ROM.
Adobe Reader
It is necessary to read the operating instructions in the provided CD-
ROM.
The audio function will not work if a sound card is not installed in the PC.
Audio may be interrupted depending on network traffic.

4
Package Contents
 NVR Network Video Recorder
 Power Cord
 Ethernet Cable
 Screw Bag
 Product CD

5
Hardware Description
Front View Rear View
1. HDD LED indicator
2. Network LED indicator: LAN 1, LAN 2
3. Power LED indicator
4. One-touch backup button with LED indicator
5. USB3.2 Gen 1 x 2 (Front)
6~21. HDD 1 to HDD 16
22. Reset button
23. DI/DO (4 x in, 4 x out)
(L) (R)
(L) Max24V, DI_GND, DI-4, DI-3, DI-2, DI-1, OCOM, DO4, DO3, DO2, DO1 (R)
24. 2.5 Gigabit Lan ports x 2
25. USB 3.2 Gen 1 x 4 (Rear)
26. HDMI 2.0a x 2
27. Power switch
28. Power connector

6
Hard Disk Installation
Please follow the steps as illustrated below to install the hardware:
 Take out the disk tray from NVR.
 Connect the Ethernet cable to the port
of 2.5 Gigabit LAN.
 Install the hard disk in each tray
and lock the disk with four
screws. Ensure the disk holes
match the holes at the base of
disk tray.
 Connect the power cord to power
connector.
 Insert the disk tray into NVR and
push it to the end.
 Turn on the server and there is a beep
to indicate the NVR is in booting
process. Please wait for minutes until
NVR beeps another time. The
installation of NVR is complete right
now.

7
Connection to DIGIEVER NVR
Please insert the product CD-ROM on a PC to install EZ Search and S-NVR
Decoder. Finally, you can start Quick Configuration on a web page.
Install EZ Search for finding NVR in the network.
Install S-NVR Decoder.
Connect to the configured NVR, download and install NVR-Client.exe
Install EZ Search
Please execute the product CD and click “Install EZ Search.”
Follow the instructions to install and the EZ Search will run automatically.
Install S-NVR Decoder
Click “Install S-NVR Decoder” and follow the instructions to setup.

8
Connect to NVR
1. Connect to DIGIEVER NVR
After setting the EZ Search and S-NVR Decoder, the user can connect to
the monitoring page by the following two options:
1) EZ Search
Once you click “Connect” or double click the selected NVR list, the
IE browser will pop up automatically.
2) Web browser (IE, Chrome, Firefox, Opera)
Login to the system by entering its IP address in web browser.

9
Note: There are 2 methods to set network:
Obtain an IP address automatically (NVR Default)
Obtain an available dynamic IP address assigned by a DHCP
server. If this option is selected, DIGIEVER NVR will automatically
obtain an available dynamic IP address from the DHCP server
once it connects to the network.
Specify an IP address
If there is no DHCP server existing in network environments, the
static IP address will be given as 192.168.1.245. It should be
adaptable in most networking environment, and user can choose
to maintain the default IP address or change it in this page.
However, it’s recommended setting different IP address of
DIGIEVER NVR if there is more than one DIGIEVER NVR in the
same LAN.
2. Enter a user name and password
Log in the NVR with the default administer account (user name: admin,
password: admin).
3. Download and install NVR-Client.exe, a software application, to execute
liveview monitoring and video playback.