Digital Watchdog MEGAPIX PANO DWC-PZV2M72T User manual

Quick Start Guide
DWC-PZV2M72T
WHAT’S IN THE BOX
QSG Manual 1 Set Screw & Plastic
Anchor – 4pcs 1 Set
Manual CD 1 Set Tor x Wrench 1 Set
Template Sheet 1 Set
Username: admin Password: admin
Attention: This document is intended to serve as a quick reference page for initial set-up.
It is recommended that the user read the entire instruction manual for complete and proper camera usage.
Tel: [phone]
Technical Support Hours: 9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
Quick Start Guide
Step 1 – PREPARING TO MOUNT THE CAMERA
Step 3 – INSTALLING THE CAMERA MODULE
Step 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
1. Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall
or ceiling.
2. For the installation process, remove the dome cover from the camera module by loosening the screws
on the dome. Use the wrench provided with the camera.
5. Assemble the dome cover over the camera body and detach the protecting film from the dome bubble.
3. Pass the wires through the mount bracket and make all necessary connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch, connect the camera using an Ethernet
cable for both data and power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch, connect the camera to the switch
using an Ethernet cable for data transmission and use a power adapter to power the camera.
NOTE: If you plug the camera into PoE+ but then plug that switch into a regular PoE it will not work.
Power Requirements Power Consumption
DC 12V
PoE IEEE 802.3atPoE+ / PoE Class 3
12VDC: 22.5W
PoE+: 25.5W
Resetting the camera: To reset the camera, use the tip of a paper clip or a pencil and press the
reset button. Pressing the button for five (5) seconds will initiate a camera-wide reset of all the settings,
including network settings.
1
2
3
Template
Sheet
Reset Button
Power
Network
Connection
4. To use the camera’s water proof wiring:
(1).Install the LAN cable into (a).
(2).(b) will be assembled to (a) with a 1/4 turn.
(3).Thread (c) tightly to (b).
a
b
c

Step 5 – DW IP FINDER™
Use the DW IP Finder™included in the camera’s accessory CD to scan the network and detect all MEGApix®
cameras. Use the DW IP Finder™to set the camera’s network settings, perform firmware upgrade or access
the camera’s web client.
Quick Start Guide
Rev Date: 02/16 Copyright © Digital Watchdog. All rights reser ved. Specifications and pricing are subjec t to change without notice.
Step 6 – WEB VIEWER
Once the camera’s network settings have been setup properly, you can access the camera’s web viewer
using the DW IP Finder. To open the camera’s web viewer:
1. Find the camera using the DW IP Finder.
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website.’ The camera’s web viewer will open up in your default web
browser.
4. Enter the camera’s username and password (default are admin / admin).
5. If you are accessing the camera
for the first time, install the ActiveX
files in order to view video from the
camera.
Network Setup
1. Run the CD included with the camera and click on the DW IP Finder™file.
2. The software will scan your network for all supported cameras and display the results in the table. Allow up
to 5 seconds for the IP Installer to find the camera on the network.
3. You can press the ‘Refresh List’ to search the network again, or filter the search results by entering a value
in the filter box at the bottom of the page.
4. Check the box next to ‘Display Camera Thumbnail’ to view a JPEG image of the camera’s view next to the
camera name on supported models.
5. Select a camera from the list by double-clicking on it. The camera’s network information will appear.
If necessary, you can adjust the camera’s network type.
6. The camera’s default network information is:
7. To view the camera’s web viewer, click on ‘View Camera Website.’
8. To save the changes made to the camera’s settings, input the ID
and PW of the camera for authentication and click ‘Save’.
9. If the camera needs to be rebooted after the settings were changed, press the ‘Reboot’ button.
The camera will cycle power and will appear back in the search results once the reboot is complete.
10 . To update the camera’s firmware from the DW Desktop Tool™, click on the firmware tab, upload the
firmware file and select the cameras to update. You can update multiple cameras at the same time.
Step 4 – ADJUSTING THE CAMERA’S SENSORS
The camera’s four individual sensors can be rotated and tilted to adjust the camera’s views using the
motorized options in the camera’s web viewer.
Select DHCP if the internet service is dynamic IP. This will allow the camera to receive its IP address
from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask, Gateway and DNS information.
Contact your network administrator for more information.
Default TCP/IP information
• IP: 169.254.X.X • Gateway: 192.168.1.1
• Subnet Mask: 255.255.255.0 • DNS: 168.126.63.1
‘Port Forwarding’ has to be set in your network’s router for
external access to the camera.
Default ID / PW : admin / admin
Server Minimum Requirements
Processor Intel® Core ™ i3-3220 CPU @3.30GHz or similar
RAM 8GB Required (16GB Recommended)
Hard Drive Sata 6 Gb/s, 64 MB cashe, 1 TB, 7200 RPM
Client Minimum Requirements (for a single 4K resolution video monitor)
Processor Intel® Core™ i5-2500 CPU @3.3 GHz or similar
RAM 8GB Required (16GB Recommended)
Graphic Card NVIDA Quadro K6000, 1GB DDR3 or similar
SERVER AND CLIENT REQUIREMENTS