Digital Watchdog DWC-PZ21M69TW User manual

User’s Manual Ver. 10/22
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
MEGApix® PANOTM 21MP 180°
Panoramic View Camera
DWC-PZ21M69T - silver-color housing
DWC-PZ21M69TW - white-color housing

Safety Information
This symbol indicates that dangerous voltage
consisting a risk of electric shock is present within
this unit.
Warning Precaution
This exclamation point symbol is intended to alert the
user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
To prevent damage which may result in fire or electric shoc
hazard, do not expose this appliance to rain or moisture.
WARNING
Be sure to use only the standard adapter that is specified i
the specification sheet. Using any other adapter could caus
fire, electrical shock, or damage to the product
Incorrectly connecting the power supply or replacing battery
may cause explosion, fire, electric shock, or damage to th
product.
Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause excessive heat generation
or fire
Securely plug the power cord into the power receptacle.
Insecure connection may cause fire
When installing the camera, fasten it securely and firmly
A falling camera may cause personal injury.
Do not place conductive objects (e.g. screw drivers, coins,
metal items, etc.) or containers filled with water on top o
the camera. Doing so may cause personal injury due to fire
electric shock, or falling objects.
Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause fire or electric shock
If any unusual smells or smoke come from the unit, stop
using the product. Immediately disconnect the power sorce
and contact the service center. Continued use in such a
condition may cause fire or electric shock
If this product fails to operate normally, contact the nearest
service center. Never disassemble or modify this product in
any way.
When cleaning, do not spray water directly onto parts of the
product. Doing so may cause fire or electric shock
WARNING
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Precaution
Operating
• Before using, make sure power supply and all other parts are
properly connected.
• While operating, if any abnormal condition or malfunction
is observed, stop using the camera immediately and contact
your dealer.
Handling
• Do not disassemble or tamper with parts inside the camera.
• Do not drop the camera or subject it to shock or vibration as
this can damage the camera.
• Clean the clear dome cover with extra care. Scratches and
dust can ruin the quality of the camera image.
Installation and Storage
• Do not install the camera in areas of extreme temperature,
exceeding the allowed range.
• Avoid installing in humid or dusty environments.
• Avoid installing in places where radiation is present.
• Avoid installing in places where there are strong magnetic
ÿelds and electric signals.
• Avoid installing in places where the camera would be subject
to strong vibrations.
• Never expose the camera to rain or water.

Important Safety Instructions
Disposal of Old Appliances
1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately form the municipal waste stream
stream in accordance to laws designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of your old appliance, please contact your city office,
waste disposal service or the shop where you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interferenece at his own expense.
1. Read these instructions. - All safety and operating instructions should be read before installation or operation.
2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use instructions should be followed.
5. Do not use this device near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet
basement; near a swimming pool; etc.
6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and
openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it
from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or other similar
surfaces. This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and the manufacturer’s instructions have been adhere to.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug the apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.

Table of Contents
Introduction
Product & Accessories......................................................................................................................................................................5
Parts Name...........................................................................................................................................................................................6
Installation
Installation.....................................................................................................................................................................................8-11
Cabling...............................................................................................................................................................................................12
SD Memory Card.............................................................................................................................................................................14
Network Setup
DW IP Finder.....................................................................................................................................................................................15
Web Viewer
Login to the camera.......................................................................................................................................................................16
GUI Overview.............................................................................................................................................................................17-18
Camera Settings
Settings>Video & Audio Setup............................................................................................................................................21-29
Settings>Camera Setup>Alignment Configuration..........................................................................................................30
Settings>Camera Setup>Camera Image Adjustment.......................................................................................................31
Settings>Camera Setup>Camera Exposure Settings........................................................................................................32
Settings>Camera Setup>Camera Day/Night Settings......................................................................................................33
Settings>Camera Setup>Camera Backlight Settings........................................................................................................34
Settings>Camera Setup>Camera White Balance Settings..............................................................................................35
Settings>Camera Setup>Camera Image Enhancement Settings.................................................................................36
Settings>Camera Setup>Video Enhancement....................................................................................................................37
Settings>Network Setup.......................................................................................................................................................38-47
Settings>Trigger Action Setup............................................................................................................................................48-51
Settings>Event Setup.............................................................................................................................................................52-56
Settings>Record Setup..........................................................................................................................................................57-62
Settings>Security Setup........................................................................................................................................................63-69
Settings>System Setup>System Information......................................................................................................................70
Settings>System Setup>Firmware....................................................................................................................................71-72
Settings>System Setup>Date&Time.......................................................................................................................................73
Settings>System Setup>DST.....................................................................................................................................................74
Settings>System Setup>Users..................................................................................................................................................75
Settings>System Setup>System Log......................................................................................................................................76
Settings>System Setup>Factory Reset..................................................................................................................................77
Settings>System Setup>Restart...............................................................................................................................................78
Settings>System Setup>System Open Source License...................................................................................................79
Appendix.............................................................................................................................................80-82
FAQs..........................................................................................................................................................83
Dimensions...............................................................................................................................................84
Warranty...................................................................................................................................................85
Limits & Exclusions...................................................................................................................................86
Disassembling the Camera............................................................................................................................................................7
Factory Reset......................................................................................................................................................................................7

7
Introduction -
Product & Accessories
Torx Wrench Moisture Absorber - 2pcs
& Absorber Guide
Waterproof cap & Gasket
Camera
Cables
Please check if all the camera and accessories are included in the package.
Manual CD Quick Manual

8
Introduction -
Part Name
Safety Wire
Alarm In/Out
Audio In/Out
Lens
SD Card Slot
Glass
CDS Sensor
Bottom Case
Reset Button
Tilt Adjusting Screw
DC Power Jack
RJ-45 Connector
Waterproof Cap

9
Installation -
Disassemble the camera
Before installing your camera, you have to read the following cautions.
1. You have to check whether the location can bear five times of the weight of your camera.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fire.
3. When installing your camera, don’t allow any person to approach the installation site. If you have any valuable
things under the place, move them away.
1Detach the dome cover by torx wrench provided
from bottom case before installation the camera.
Match the one screw hole on the dome cover
and camera bottom specially.
Reset to the Factory Default
Press the reset button for 5 seconds to return the
setup to the factory default.
Warning :
If you press the ‘Reset’ button, you will lose all
setting data. If needed, please, make a note for
further installation.
Reset Button

10
Installation -
Installation
1Attach the Bottom case to selected Mount Bracket.
2Connect the Mount Cap and Tilt Bracket.
3Fix it with safety wire on the Bottom case and fasten it
to fit the joint of Bracket and Bottom case well.
4Assemble the Bottom case and Bracket.
Be sure to assemble the camera and bracket to match
the case outline.
5To achieve desired view direction and orientation, rotate
3-axis gimbal. To fix the setting, tighten the tilt stopper
screw.
Tilting Angle can be adjusted by screw.
6Assemble the Upper case.
7Adjust the Tilt angle and fix it with the Tilt Mount screw.
You can adjust the direction and height with the Panning
Bracket.
8After completing the installation remove the protective
film.
UNLOCK
LOCK
25°
0°
50°
BJ13 BJC05BC13 BW13
[ Accessory Bracket ]

11
Installation -
Installation
1After removing the new bracket coupling bolt with a flat
head screwdriver, remove the rubber cap of the fastening
point.
2Connect the mount bracket to the camera with the
mount screw.
3To achieve desired view direction and orientation, rotate
3-axis gimbal. To fix the setting, tighten the tilt stopper
screw.
Tilting Angle can be adjusted by screw.
8Secure the dome cover to the camera’s bottom case using
the torx wrench.
Installation method with the old type bracket

11
Installation -
Adjusting the camera angle
Tilting 18°
Rotating 53°

Cabling
Installaon -
Power
Ethernet cable
Ethernet cable
PoE Injector
Use a PoE-Injector to connect data and power through a single cable and begin viewing and recording images instantly.
A non-PoE switch will require an adaptor for power transmission.
2. Using a Non-PoE Switch1. Using a PoE-Injector
Two Opons
Ethernet Switch
If a PoE-enabled switch is not used, use a power adaptor
for power transmission and non-PoE switch for data
transmission.
Follow the illustraons below to connect the camera
without a PoE-enabled Switch.
The Camera is PoE-compliant, allowing transmission of
power and data via a single Ethernet cable.
PoE eliminates the need for the different cables used to
power, record, or control the camera. Follow the illustraon
below to connect the camera to a PoE Injector using
an Ethernet cable.
10

Cabling
Installaon -
Audio Output
Connect the ‘Audio Out’ cable of the camera to device like
speaker.
Audio Input
Connect the ‘Audio In’ cable of the camera to the device like
microphone.
Power Connecon
Please, check the voltage and current capacity of rated power
carefully.
Network Connecon
Connect the crossover cable into the RJ-45.
Rate
Power Current
Consumption
DC 12V 2A
PoE
IEEE 802.3at PoE+
Alarm Output
It connects to the alarm lights, siren or lamps, and it is
acvated according to the Setup menu seng.
Cable of the relay output device should connect to sky blue
and purple line of the Alarm Cable.
Alarm Input/Sensor
Cable of the sensor/alarm input device should connect to
yellow and white line of the Alarm Cable.
1
2
3
4
5 6
Audio Out supports only RTSP Back channel funcon. It plans to make it
available on the web later.
11
Audio Input
Audio Output
Power
Network
~Alarm In/Out
1
2
3
4
5 6
Alarm Output
Alarm Input
5
6
DI (+)
DI ( - )
DO ( - )
DO (+)
WHITE
YELLOW
SKY BLUE
GRAY + DOT

14
Installation -
Inserting/Removing an SD Memory Card
Micro
The memory card is an external data storage
device that has been developed to offer an
entirely new way to record and share video,
audio, and text data using digital devices.
Recommended SD Card Specification (Not
Included)
- Type: Micro SD (SD/SDHC/SDXC)
- Manufacturer: SanDisk, Samsung,
Transcend, Micron
- Capacity: 4GB~128GB
- Class: UHS-I U3 Class 10
New Micro SD card over 64GB must be
formatted on the first use.
1Inserting an SD Memory Card
Insert the SD card in the arrow direction.
Don’t insert the SD memory card while it’s
upside down by force. Otherwise, it may damage
the SD memory card.
2Removing an SD Memory Card
Removing a SD Memory Card Gently press down
on the exposed end of the memory card as shown
in the diagram to eject the memory card from
the slot.
Pressing too hard on the SD memory card can
cause the card to shoot out uncontrollably from
the slot when released.
If you have saved data in the SD memory card,
removing the SD memory card prior to setting
record to OFF will cause damage to the data
stored in the card.

6To save the changes made to the camera's settings, input
ID and PW of the camera for authentication.
7If the camera needs to be rebooted after the settings were
changed, press the 'Reboot' button. The camera will power
cycle and will appear back in the search results once the
reboot is complete.
8 Click 'Save' to save changed values.
9 To update the camera's firmware from the DW IP FinderTM,
click on the firmware tab, upload the firmware file and
select the camera to update. You can update multiple
cameras at the same time.
1Go to : http://www.digital-watchdog.com and search for
‘IP Finder’ on the quick search bar at the top of the page.
2The latest IP Finder software will appear in the search
results. Click on the link to download the file to your
computer.
3The software will scan your network for all supported
cameras and display the results in the tabel. Allow up to
5 seconds for the IP Installer to find the camera on the
network.
4You can press the ‘Refresh List’ to search the network
again, or filter the search results by entering a value in
the filter box.
5Check the box next to ‘Display Camera Thumbnail’ to view
a JPEG image of the camera’s view next to the camera
name on supported models.
Network Setup -
DW IP FinderTM
iThe default network type of camera is DHCP mode.
iIf you have a DHCP server, it will automatically set the
Camera IP.
iContact your network administrator for more
information.
13
Thumbnail view
Select network to scan
Filter device type to scan
Scan devices
Show/hide
thumbnail view
Refresh thumbnail view
Bulk IP assignment
Firmware upgrade
Firmware version
Camera's uptime
Open device
configuration
settings
Device's
information
iDefault ID / PW : admin / admin
i For security purposes, it is highly recommended to
change your password after initial setup.

Network Setup -
Quick Start of Network Connection
11 Access your IP Camera via the Internet :
If you use a static IP address assigned by your ISP
1) Open Internet Explorer.
2) Type the IP of the IP Camera.
3) If you use a router, type the routers’ static IP and the
web port number of the IP Camera.
If you have a dynamic address provided by your ISP
1) Open Internet Explorer and visit the DDNS website.
2) Register the IP Camera.
3) Reboot the IP Camera.
4) Give the DDNS server 10 minutes to locate your IP
Camera’s IP information.
5) Click the refresh button in the Internet Explore.
6) After your camera is connected, select your camera.
Please follow the steps below to complete
the initial setup of the network function.
1ConnecttheIPCameraandPCtotheconfigurednetwork.
2Open the IP Installer on a PC, then search for the
IP camera.
3If multiple numbers of camera are connected it should be
distinguished by the mac address of the Camera.
4Click the Camera IP, and connect to the WEB PAGE.
5Default ID/Password to access IP Camera are both the
word: admin.
6Familiarize yourself with the Viewer Interface Screen.
7Please install VLC to display live video.
8The IP setting can be set to ‘STATIC’ at IP Installer or web
viewer followed by Setup -> Network -> Network Settings
9If the IP Camera is connected to a network which utilizes a
router,youmusthavePortForwardingconfiguredonyour
personal router to forward all ports to the IP address you
have assigned the IP Camera.
10 AfterconfiguringPortForwardingonyourrouter
(if necessary), you may access your IP Camera on your local
network by opening Internet Explorer and specifying the IP
address and Web Port that you have assigned to the IP
Camera.
iPlease do not power on the IP Camera until instructed.
iTemporarilydisableanyproxyserversconfiguredin
internet Explorer.
iIf connecting the IP Camera directly to a modem,
power down and reset the modem. Leave the modem
powereddownuntilconfigurationsarefinalizedwith
the IP Camera and the IP Camera has been correctly
connected to the modem.
iIf you have a DHCP server, it will automatically set
the Camera IP.
iIf you do not have a DHCP server, Camera IP is set to
192.168.1.80 after one minute. In this case, PC IP
must be changed to the IP to be able to access the
192.168.1.80.
iExample: http://192.168.0.200:8888
iIf you leave your Web Port set to 80, you don’t need
to specify the port in the Address Bar to access to
your IP Camera.
14

If you have DYNAMIC IP service from your
Internet Service Provider (ISP), you can’t tell
the current IP address of the IP Camera.
To solve this problem, you have to register to
our DDNS service.
At first, you have to check if you are using
dynamic addressing. If so, register your IP
Video Server on our DDNS website before
you configure, setup, or install the IP Camera.
Even though your IP is not dynamic, you will
get benefit if you register to DDNS. In this
case, just remember ‘hostname.dyndns.
com/gate1’ instead of complicated series of
numbers like http://201.23.4.76:8078.
For more details, contact our Support Center.
To use a public DDNS called ‘dyndns’ or ‘no-ip’,
refer to the detail information on how to use the service.
(Visit the web site : http://www.dyndns.com
or http://www.no-ip.com)
Network Setup -
DDNS Registration
15

Network Setup -
Guide to Network Environment
Please configure the IP Camera at the
installation site. You must determine your
network scenario in order to configure the IP
Camera with the proper TCP/IP settings.
This tutorial will guide you through the
process. Before actually configuring the IP
Camera, determine settings to be applied.
Record those settings to be used to configure
your IP Camera for reference.
When configuring your IP Camera, treat the
IP Camera as another PC on your network.
You will assign it several addresses and other
TCP/IP properties to match your current
network.
This step-by-step tutorial will teach what IP
addresses and network configurations should
be assigned based on the network scenario.
1Before you begin, locate any information and settings
received from your Internet Service Provider (ISP).
You may need to refer to these IP addresses at a later time
duringtheconfiguration.
2You must determine whether the IP address is STATIC or
DYNAMIC. At this moment, you are only concerned about
the ISP. Did they provide you with a STATIC or DYNAMIC
address? If you are unsure, contact your ISP.
3ConfigureyourIPCamera’sTCP/IPsettingsfornetwork
connectivity by selecting Setup from the main interface
and selecting TCP/IP located on the left of the
Setup screen.
4If prompted for ID and Password, use ‘admin’ for both
entries. The default web port number is 80. If port 80 is
blocked by the ISP, a value between 1025 ~ 60000 should
be used. If TCP port 80 is blocked, consult the ISP.
5The following descriptions are several basic network
scenarios. Determine which scenario describes your
network. If your network does not match one of the
scenarios below and you are unsure how to setup your IP
Camera, contact your network administrator and then call
our Support Center.
iIf you were not given any IP addresses or the ISP was
responsible for the setup and installation of
your Internet connection, go to step 2.
iIf you are not using a router on your network,
your ‘Current TCP/IP Settings’ (from the previous
section) and ‘Assigned IP Addresses from My ISP’ will
be exactly the same.
iYou cannot control the rectangular gray areas and
only the ISP has access to the devices.
IP Address
Subnet Mask
Default Gateway
Primary DNS Server
Secondary DNS Server (Option)
Current TCP/IP Settings
Static □Dynamic □
16

Network Setup -
Setup Case A, B
Configure your IP Camera’s TCP/IP properties
as follows :
1Network Type : STATIC (even though you have Dynamic IP
from your ISP, use STATIC on the IP Camera)
2Internet Address : A private IP address such as
192.168.0.200 (Example)
3Subnet Mask : 255.255.255.0 (Example)
4Default Gateway : 192.168.0.1 (Example)
5Preferred DNS Server : Use the 1st DNS Server from
‘Assigned IP Address from My ISP’.
6DDNS Server : Use the DDNS server.
7Web Port : 8888
Case A:
Dynamic IP + Personal Router [Most SOHO]
Case B:
Static(Fixed) IP + Personal Router [Efficient]
iYou need to assign an IP address to the IP Camera just
as you do with PC.
iThe IP address you assign must be unique to your
network and match your network as well.
For information on how to choose a unique IP and
match your network, read the FAQ.
iThe IP address you assign must be a private IP.
For information on how to choose a private IP please,
read the FAQ.
iYou must use the same subnet mask as the one you
noted under ‘Current TCP/IP Settings’.
iIf you did not receive any IP addresses from your ISP,
contact the ISP and acquire the IP address of their
DNS server.
iDo not use the default port 80 as this number must be
changed.
iYou may select any number between 1025 ~ 60000.
iThis is the same site you will register later to
accommodate dynamic IP from your ISP.
iThis IP address must be the IP address of your router.
(private or LAN side)
iUse the same Default Gateway you noted under
‘Current TCP/IP Settings’.
Camera
Personal Router
W/Integrated Switch
Cable/xDSL Modem
(ISP Provided)
Phone Line
or CATV
PC
Internet
Camera
Personal Router
W/Integrated Switch
Gateway or Router
at ISP
Public Line
PC
Internet
17

Network Setup -
Setup Case C, D
Case C:
Static(Fixed) IP
[Dedicated line directly to the IP Camera]
Case D:
Dynamic IP + DSL/Cable Modem
[Connected directly to the IP Camera]
Camera
Cable/xDSL Modem
(ISP Provided)
Phone Line
or CATV
Internet
Configure your IP Camera’s TCP/IP properties
as follows :
1Network Type : STATIC
2Internet Address : A static IP address received from your
ISP such as 24.107.88.125 (Example)
3Subnet Mask : Subnet mask assigned from your ISP such
as 255.255.255.240 (Example)
4Default Gateway : 24.107.88.113 (Example)
5Preferred DNS Server : Use the 1st DNS Server from
‘Assigned IP Address from My ISP’
6DDNS Server : Use the DDNS server
7Web Port : 80
Configure your IP Camera’s TCP/IP properties
as follows :
1Network Type : DYNAMIC
2DDNS Server : Use the DDNS server
3Web Port : 80
Camera
Gateway or Router
at ISP
Public Line
Internet
iTo connect the IP Camera directly to a modem,
power down and reset the modem. Leave the modem
powereddownuntilconfigurationsarefinalizedwith
the IP Camera and the IP Camera has been connected
correctly to the modem. Then power on the modem,
followed by the IP Camera.
iYou need to assign an IP address to the IP Camera just
as you do with PC.
iThis is the same site you will register later to
accommodate dynamic IP from your ISP.
iYou may select any number between 1025 ~ 60000.
iIf you have not received any IP addresses from your
ISP, contact them to acquire the IP address of their
DNS server.
iThis is the same site you will register later to utilize
our DDNS service.
iUse the assigned default gateway from your ISP.
iYou may select any number between 1025 ~ 60000.
18

Network Setup -
Port Forwarding
After entering the correct TCP/IP settings,
you are ready for ‘Port Forwarding’
(Cases A, B).
1Please record the TCP/IP settings of your IP Camera for
future reference. You may need this information to access
yourIPCameraandtoconfigure‘PortForwarding’.
2After clicking ‘Apply’, the system will prompt for reboot.
Please allow the system 50 seconds to reboot and accept
thechanges.After50seconds,closetheconfiguration 
screen.
The view will display ‘Trying to Reconnect’. If the ACTIVE
lightontheIPCamerahasgoneoffandisnowbackon 
againflashing,theIPCamerahasrebooted.Afterthe 
system reboots completely, remove the power supply from
the unit and close Internet Explorer.
3Return your PC/Laptop TCP/IP properties to their original
settings.
4Before installing the IP Camera, you must use
‘Port Forwarding’ on your personal router (Cases A, B).
You will need to forward 1 ports:
· Web Port
All the ports will be forwarded to the IP address you
assigned to the IP Camera.
In the example above, you would forward:
· 8888 > 192.168.0.200
iFor information on how to use ‘Port Forwarding’,
please read Appendix C.
IP Address
Subnet Mask
Default Gateway
Preferred DNS Server
DDNS Server
Web Port
IP Camera TCP/IP Settings
19