digitalview 4175200XX-3 User manual

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 1 of 60
PC, DVI, VIDEO, HD Component INTERFACE CONTROLLER
FOR TFT PANEL
Model: SVH-1920v2
Part number : 4175200XX-3 or up
INSTRUCTIONS
CONTENTS
Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer
3. System design – Diagram of a suggested system
4. Assembly notes – Important information about system elements
6. Connection & Operation – How to use the controller
13. Connectors, pinouts & jumpers – Essential connection information
27. Controller dimensions
28. Application notes
30. Troubleshooting
31. Specifications
32. Appendix I – Supported graphics modes table
35. Appendix II – RS-232 control protocols
48. Appendix III – Mapping definition
52. Appendix IV – Auto Color Gain
53. Appendix V – DV remote control unit work for SVH-1920v2
54. Appendix VII – PIP mix table
55. Appendix VII – HD-1000 / HD-2000 connection
56. Appendix VIII – Procedure for showing how to select the baud rate
58. Warranty, Caution & Limitation of Liability, Trademarks
59. Contact details
60. Revision History
It is essential that these instructions are read and understood before connecting or
powering up this controller.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 2 of 60
Introduction
Designed for LCD monitor and other flat panel display applications, the SVH-1920v2 is a feature rich interface
controller for :
TFT (active matrix) LCD panels of 1920x1200, 1920x1080, 1920x480, 1600x1200, 1600x900, 1680x1050, 1440x900,
1366x768, 1280x1024, 1280x800, 1280x768 1024x768, 1024x600, 800x600, 800x480 and 640x480 resolutions.
Computer video signals of VGA, SVGA, XGA, SXGA, WXGA, UXGA, WUXGA standard.
Video signals of NTSC, PAL and SECAM standard.
DVI input support up to 1920x1200 60Hz input signals
HD-SDI input support by using optional HD-SDI adaptor board (Kit P/N 546013410-3 / P/N 546013310-3 )
Ordering information :
Controller Part number Ordering part number
SVH-1920v2 P/N 41752003X-3 P/N 4175200XX-3
HOW TO PROCEED
Ensure you have all parts & that they are correct, refer to:
•Connection diagram
•Connector reference (in following section)
•Assembly notes (refer to page 4 – 5)
Check controller switch & jumper settings (errors may damage the panel)
Prepare the PC
Connect the parts
Understand the operation & functions
IMPORTANT USAGE NOTE
This equipment is for use by developers and integrators, the manufacturer accepts no liability for damage or injury
caused by the use of this product. It is the responsibility of the developer, integrators or other user of this product to:
•Ensure that all necessary and appropriate safety measures are taken.
•Obtain suitable regulatory approvals as may be required.
•Check power settings to all component parts before connection.
DISCLAIMER
There is no implied or expressed warranty regarding this material.
Controller Solution Generator
Full web resource matching controllers & panels with connection diagrams for download.
See
at
:
http://www.digitalview.com/controllers/csg.php

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 3 of 60
SYSTEM DESIGN
A typical LCD based display system utilizing this controller is likely to comprise the following:

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 4 of 60
ASSEMBLY NOTES
This controller is designed for monitor and custom display projects using 1920x1200 or 1920x1080 or 1600x1200 or 1600x900
or 1680x1050 or 1440x900 or 1366x768 or 1280 x 1024 or 1280x800 or 1024 x 768 or or 1024x600 or 800x600 or 800x480 or
640x480 resolution TFT panels with a VGA, SVGA, WXGA, XGA, SXGA, UXGA or WUXGA signal input. The following
provides some guidelines for installation and preparation of a finished display solution.
Preparation: Before proceeding it is important to familiarize yourself with the parts making up the system and the various
connectors, mounting holes and general layout of the controller. As much as possible connectors have been labeled. Guides
to connectors and mounting holes are shown in the following relevant sections.
1. LCD Panel: This controller is designed for typical LVDS interfaced panels with panel voltage 3.3V, 5V or 12V, External for
12V~18V interface. Due to the variation between manufacturers of panels signal timing and other panel characteristics,
factory setup and confirmation should be obtained before connecting to a panel. (NOTE: Check panel power jumper
settings before connection)
2. Controller: Handle the controller with care as static charge may damage electronic components. Make sure correct
jumper and dip switches settings to match the target LCD panel.
3. LCD signal cable (LVDS panel): In order to provide a clean signal it is recommended that LVDS signal cables are no
longer than 46cm (18 inches). If those wire cabling is utilized these can be made into a harness with cable ties. Care
should be taken when placing the cables to avoid signal interference. Additionally it may be necessary in some systems
to add ferrite cores to the cable to minimize signal noise.
5. Inverter: This will be required for the backlight of an LCD, some LCD panels have an inverter built in. As LCD panels
may have 1 or more backlight tubes and the power requirements for different panel backlights may vary it is important to
match the inverter in order to obtain optimum performance. See Application notes page 18 for more information on
connection.
6. Inverter Cables: Different inverter models require different cables and different pin assignment. Make sure correct cable
pin out to match inverter. Using wrong cable pin out may damage the inverter.
7. Function Controls: The following section discusses the controls required and the section on connectors provides the
detail. The controls are minimal: On/Off, Backlight Brightness (depends on inverter), OSD (5 momentary buttons) analog
VR type or (8 momentary buttons) digital type.
The 8 momentary buttons OSD switch mount P/N 416100520-3 or OSD membrane interface P/N 416100120-3 must be
used when 24VDC input.
8. Function controls cable: The cables to the function switches should be of suitable quality and length so that impedance
does not affect performance. Generally lengths up to 1 meter (3 feet) should be acceptable.
9. Status LED: The pin direction of the LED should be corrected for right colour indication. Red colour stands for standby.
Green colours stands for signal on. The status LED is an optional part only, can be unconnected.
10. IR sensor: It is an optional part only, can be unconnected if not using IR remote control. See Appendix V in details.
11. RS-232 control interface : Firmware upgrade and serial control via CN8 interface port.
12. Audio add-on board P/N 416940020-3: The audio add-on board gives the audio input and output signal connection. It is
an optional part only, can be unconnected if not using audio.
13. VGA Input Cable: Plug the VGA cable to the connector P1 (for VGA 1) or P2 / CN6 (for VGA 2) on the controller board.
As this may affect regulatory emission test results and the quality of the signal to the controller a suitably shielded cable should
be utilized.
14. DVI-D input cable : Plug the DVI cable to the connector P2 on the controller board.
15. Composite video input : Standard Composite cables can be used. Reasonable quality cable should be used to avoid
image quality degradation.
16. S-Video input : Standard S-video cables can be used. Reasonable quality cable should be used to avoid image quality
degradation.
17. Alternate composite 1 and S-video 1 input : Plug the video input cable P/N 426000500-3 on CNV1 connector
18. HD component video input :Plug the component video input cable P/N 426000600-3 on CNV2 connector

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 5 of 60
20. Interface for connecting to HD-SDI adaptor board
HD-SDI (1-in-1-out) adaptor board, Kit number P/N 546013410-3 includes :
HD-1000 adaptor (1-in-1-out) P/N 416013410-3
Ribbon cable P/N 426171120-3, 180mm
HD-SDI (2-in-2-out) adaptor board, Kit number P/N 546013310-3 includes :
HD-2000 adaptor (2-in-2-out) P/N 416013310-3
Ribbon cable P/N 426171120-3, 180mm
21. Power Input: 12V/24VDC is required, this should be a regulated supply. The power rating is depending on the panel and
inverter used. Normally, power supply with 3.5Amp current output should enough for most of 4x CCFT panels. Although the
controller provides power regulation for the LCD power this does not relate to the power supplied to the backlight inverter. If an
unregulated power supply is provided to an inverter any fluctuations in power may affect operation, performance and lifetime of
the inverter and or backlight tubes.
22. External panel power input : Allow to supply external power to the panel separately for max 3.3V (7A) or 5V (7A) or 12V
(5A) or 18V (3.5A) via PP4 power input connector.
23. Auxiliary video input : This port provides Composite video 1 & 2, S-video 1 & 2. The video input selection can be
switched via RS-232 command (0x98).
24. Auxiliary +5VDC output : 2 ways connector provides +5VDC output.
25. Ambient light sensor connection : 3 ways connector provides interface for ambient light sensor connection.
26. Backlight status input : 2 ways connector provides interface for connection with panel which support the panel with
backlight status monitoring function.
•
••
•Power output: Note the controller has an overall 3Amp current limit and the current available from the auxiliary power
output will be dependent on the power input and other system requirements.
•
••
•Power Safety: Note that although only 12V / 24VDC is required as ‘power-in’ a backlight inverter for panel backlighting
produces significantly higher voltages (the inverter does not connect to the ground plane). We strongly advise
appropriate insulation for all circuitry.
•
••
•EMI: Shielding will be required for passing certain regulatory emissions tests. Also the choice of external Controller to PC
signal cable can affect the result.
•
••
•Ground: The various PCB mounting holes are connected to the ground plane.
•
••
•Servicing: The board is not user serviceable or repairable. Warranty does not cover user error in connecting up to the
controller and is invalidated by unauthorized modification or repairs.
•
••
•Controller Mounting: It is recommended that a clearance of at least 10mm is provided above and 5mm below the
controller when mounted. Additionally consideration should be given to:
•Electrical insulation.
•Grounding.
•EMI shielding.
•Cable management. Note: It is important to keep panel signal cables apart from the inverter & backlight cables to
prevent signal interference.
•Heat & Ventilation: Heat generated from other sources, for example the backlight of a very high brightness panel
may generate significant heat which could adversely affect the controller.
•Other issues that may affect safety or performance.
•
••
•PC Graphics Output: A few guidelines:
•Signal quality is very important, if there is noise or instability in the PC graphics output this may result in visible noise
on the display.
•Refer to graphics modes table in specifications section for supported modes.
•Non-interlaced & interlaced video input is acceptable.
IMPORTANT: Please read the Application Notes section for more information.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 6 of 60
CONNECTION & OPERATION
CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious
damage.
CONNECTION
Connection and usage is quite straight forward (it is useful to have the relevant connection diagram available at this time):
1. LCD panel & Inverter: Connect the inverter (if it is not built-in the panel) to the CCFT lead connector of the LCD panel.
LVDS type panels:The controller board has the built-in LVDS transmitter driver. Plug the LVDS cable to J3. Insert the
panel end of the cable the LCD panel connector.
2. Inverter & Controller: Plug the inverter cable to CNB1 and CNA1 (if necessary). Plug another end to the connector on
the inverter.
3. Function switch & Controller: Plug the OSD switch mount cable to CNC1 on the controller board and another to the
OSD switch mount.
4. LED & Controller: Plug in a 3-way with dual colour LED to connector LED1 on the controller board.
5. IR & Controller: Plug in a 3-way with IR sensor to connector IR1 on the controller board.
6. Jumpers & Switches: Check all jumpers and switches (SW3, SW4) are set correctly. Details referring the connection
diagram (a separate document) or the jumpers and switches setting table (in the following section).
7. Jumpers & Inverter & Panel voltage: Particularly pay attention to the settings of JA3, JA5, JA6, JB2 and JB3. JB2 &
JB3 are used for inverter control (read inverter specification and information on the jumper table to define the correct
settings). JA3 & JA5 & JA6 is used for panel voltage input (read panel specification and information on the jumper table
to define the correct settings).
8. VGA cable & Controller: Plug the VGA cable to the connector P1 on the controller board. VGA 2 is supported via P2
(DVI-I) or CN6 connector.
9. DVI cable & Controller : Plug the DVI cable to the connector P2 on the controller board.
10. Power supply & Controller: Plug the DC 12V/24V power in to the connector PP5 or PP2. You can consider to use
DigitalView mating power cable P/N 426013800-3, 160mm for PP5 connection.
11. External panel power input : Plug power cable : P/N 426013700-3 for external panel power input (3.3 (max 7A) / 5V
(max 7A) / 12V (max 5A) / 18V (max3.5))
12. Power on: Switch on the controller board and panel by using the OSD switch mount.
LED status (LED1) :
State LED color
Backlight OFF RED
Backlight ON GREEN
General:
•If you are using supplied cables & accessories, ensure they are correct for the model of panel and controller.
•If you are making your own cables & connectors refer carefully to both the panel & inverter specifications and the section
in this manual, “Connectors, Pinouts & Jumpers” to ensure the correct pin to pin wiring.
PC SETTINGS
The controller has been designed to take a very wide range of input signals however to optimize the PC’s graphics
performance we recommend choosing 60Hz vertical refresh rate – this will not cause screen flicker.
OPERATION
Once the system has been connected and switched on there are a number of functions available to adjust the display
image as summarized in the following sections. The settings chosen will be saved for each mode independently.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 7 of 60
LCD DISPLAY SYSTEM SETTINGS
NOTE: By way of explanation the following refers to a set of sample buttons that may be obtained as an option. In
addition to power on/off and connection for backlight brightness the controller provides an On Screen Display of certain
functions which are controlled by 5 momentary type buttons (analog VR type) or 8 momentary type buttons (digital type):
Controls Analog VR type Digital type
On/Off – turns controller board power on VR toggle switch On/Off button
Brightness – controls backlight brightness Rotary VR Brightness +/- buttons
Menu
–Turns OSD menu On or Off (it will auto time
off)
–
Back to previous OSD menu page
Menu button Menu button
Select down
–Moves the selector to the next function (down)
SEL DN SEL DN
Select up
–Moves the selector to the previous function
(up)
SEL UP SEL UP
+
–Increase the OSD parameter values
–Go into the sub-menu page from the top
–
Confirm to select the OSD function
+ +
-
–Decrease the OSD parameter values
- Go into the sub-menu page from the bottom
- -
Reset to Factory Defaults Press and hold SEL DN button,
then power on the controller
Press and hold SEL DN
button, then power on the
controller
Access “Programming Mode” Press and hold MENU button,
then power on the controller
Press and hold MENU button,
then power on the controller
ON/Off/Brightness
SEL UP
SEL DN
+
-
Menu
Analog VRtype
Digital type
12V / 24VDC power input :
Analog 10K VR Type OSD
switch mount uses
P/N 410680550-3 or up
12V / 24VDC power input :
Digital 10K Type OSD
switch mount uses
P/N 416100520-3 or up

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 8 of 60
Picture :
Volume
###
Increase/decrease volume level, total: 100 steps
Brightness Increase/decrease panel brightness level, total: 100 steps
Contrast Increase/decrease panel contrast level, total: 100 steps
Saturation Increase/decrease saturation, total: 100 steps
Hue ** Increase/decrease Hue level, total: 100 steps
Sharpness Increase/decrease sharpness, total: 30 steps
Backlight Backlight brightness adjustment (Functions when
light detector sets OFF)
Position
##
Aspect / Size 4
44
4
- Fill Screen : Enable full screen expansion for lower resolution Image
- Fill to Aspect Ratio: Enable fill screen expansion for lower resolution
image according to aspect ratio
- 4 : 3 : scaling format in 4:3
- 16 : 9 : scaling format in 16:9
- 16 : 10 : scaling format in 16:10
- 2.35 : 1 : scaling format in 2.35:1
- 2 : 1 : scaling format in 2:1
- 1 : 1 : Display the exact image resolution on the screen without
image expansion.
** : FUNCTION IN ARGB/ DVI / VIDEO NTSC MODE ONLY
## : FUNCTION IN ARGB MODE ONLY
### : DISPLAY WHEN AUDIO ADD-ON BOARD CONNECTED
Move the image position upward
Move the image position downward
Move the image position to the left
Move the image position to the right

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 9 of 60
Source : Select the input video signal
Main Port Change 4
VGA 1
VGA 2
DVI
Composite 1
Composite 2
S-Video 1
S-Video 2
Component 1
HD/SD SDI 1
++
HD/SD SDI 2
++
PIP Port change4
PIP Off / VGA 1/ VGA 2/ DVI / Composite 1 / Composite 2 / S-Video 1 / S-Video 2 /
Component 1 / HD/SD SDI 1 / HD/SD SDI 2
PIP Size4: Off / PIP Size 1~18 / Size by Size / Size by Size Tall
The PIP capability on display input sources refer to Appendix VII – PIP mix table
PIP Position :
PIP Blend Level : 6.25% ~ 100% : PIP Transparency
PIP Swap : Swap between the main window and PIP window
PIP Auto Turn off : : OFF / ON
ON : When PIP is no signal input after 30 seconds, the PIP
window will turn off automatically.
OFF : PIP window keeps on
++ DISPLAY WHEN HD-1000/-2000 CONNECTED
Utilities :
Setup 4
Auto Picture Setup
#
: Auto adjust the image position, phase and size
Auto Color Gain
+
4
44
4: Auto Color Calibration (See appendix IV)
- Return
- Execute
Wide Screen Mode Selection
#
4
44
4:Recognize the wide screen mode coming from ARGB port
- Group 1
-1024x768
-1280x768
-1360x768
-1366x768
- Group 2
-1440x900
-1600x900
Manual Clock
#
: Adjust the image horizontal size
Manual Phase
#
: Fine tune the data sampling position (adjust image
quality)
Auto Source Seek :
- Auto : : OFF / ON
ON – Auto source select always enable
OFF – Disable auto source select function
- Setup4
44
4Selection for the corresponding input sources detection
VGA 1
Move the PIP position upward
Move the PIP position downward
Move the PIP position to the left
Move the PIP position to the right

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 10 of 60
VGA 2
DVI
Composite 1
Composite 2
S-Video 1
S-Video 2
HD/SD SDI 1
++
HD/SD SDI 2
++
The corresponding input port name display on OSD menu will disappear once
setting “OFF”.
Auto Power : OFF / ON
ON – Enable soft power off function if absence of input signals
OFF – Disable soft power function
Video Standard (SD)
+++
4
AUTO
NTSC*
NTSC 4.43*
PAL*
PAL M*
SECAM*
(* - No image found when non-matching video system signal input)
Anti Image Retention :
Anti Image Retention :
Method : Flash / Pixel Shift / Horizontal Pan / Vertical Pan
Flash : Flashing the screen
Pixel Shift : Image shift pixel by pixel around the screen
Horizontal Pan : Display a pattern moving horizontally on screen.
Vertical Pan : Display a pattern moving horizontally on screen.
Horizontal Pan Setting :
Height > Panel Height : ÷2 / ÷4 / ÷6 / ÷8 : Configure the pattern height
Width > Panel Width : ÷2 / ÷4 / ÷6 / ÷8 : Configure the pattern width
Pattern : Black / White : Configure the pattern color
Pass : 1 ~ 100 : Configure the pattern moving cycle
Vertical Pan Setting :
Height > Panel Height : ÷2 / ÷4 / ÷6 / ÷8 : Configure the pattern height
Width > Panel Width : ÷2 / ÷4 / ÷6 / ÷8 : Configure the pattern width
Pattern : Black / White : Configure the pattern color
Pass : 1 ~ 100 : Configure the pattern moving cycle
Flash Setting :
Timer : 1 ~ 100s : Configure the flashing duration
Flash Period : 1 ~ 100 : Configure the flashing cycle
Note : Anti Image retention state will be cleared once you press the MENU button.
Gamma : 0.6 / 0.7 / 0.8 / 0.9 / 1.0 / 1.1 / 1.2 / 1.3 / 1.4 / 1.5 / 1.6 / 1.7 / 1.8 / 1.9 / 2.0 / 2.1 / 2.2
/ 2.3 / 2.4 / 2.5 / 2.6 (Effective on V1.18.00.00 or later firmware revision)
Image Orientation** 4
Normal
Horizontal Flip
Vertical Flip
Rotate
OSD 4
OSD position :
OSD Timeout (sec) : ON – 60 : Adjust the OSD menu timeout period in a step of 5
Move the OSD menu image position upward
Move the OSD menu position downward
Move the OSD menu position to the left
Move the OSD menu position to the right

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 11 of 60
seconds (max 60 seconds)
ON = Continuous to display OSD menu.
60 = 60 seconds later will turn off the OSD menu.
Language : English / Spanish / French / German / Chinese :Select OSD menu language
display
Display Input : OFF / ON : Display input source info after switching source.
IR Remote control : IR Remote Enable : Set enable on IR remote control
IR Remote Disable : Set disable on IR remote control
Freeze : Freeze the image (use “+” button)
Zoom 4
Zoom level : : Enable the zoom in function on the image displayed.
Use “+” button to zoom in the image
Use “-“ button to decrease the zoomed image
Horizontal pan : : Pan the image horizontally
Vertical pan : : Pan the image vertically
Factory Reset
Note : Freeze state will be cleared when you using zoom function.
Color Temperature 4
5000K
Red Gain :
Green Gain :
Blue Gain :
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
6500K
Red Gain :
Green Gain :
Blue Gain :
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
8000K
Red Gain :
Green Gain :
Blue Gain :
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
9300K
Red Gain :
Green Gain :
Blue Gain :
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
User setting :
Red Gain :
Green Gain :
Blue Gain :

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 12 of 60
Red Offset :
Green Offset :
Blue Offset :
Reset to Defaults : Resume to the default values
Reset All to Defaults : Resume all color temperature settings to the default values.
Hot Key 4
Hot key 1 : Brightness / Contrast / Inputs / Aspect Ratio/ Zoom / Freeze / PIP Size / PIP Swap
/ PIP ON/OFF / Saturation / Hue / Backlight / Auto Picture Setup / No Function
Hot key 2 : Brightness / Contrast / Inputs / Aspect Ratio/ Zoom / Freeze / PIP Size / PIP Swap
/ PIP ON/OFF / Saturation / Hue / Backlight / Auto Picture Setup / No Function
Backlight Setup4
44
4
- B/L Invert : : Invert for the backlight brightness
- B/L
Control : D/A / PWM : Selection for voltage level dimming control / PWM
dimming control
- Backlight Frequency : 100 ~ 440Hz in a step of 20
- Light Detector : : Enable ambient light detector function by using KIT
70220-3
- Min Backlight Level : 0 ~ 50% : Default the minimum backlight adjustment.
Default Setting 4
44
4
Reset to Factory Defaults 4
44
4(Activate when JC1 position 4 sets open)
Are you sure ? Yes/No
Reset to Factory Defaults with (Color Temp.) 4
44
4(Activate when JC1 position 4 sets open)
Are you sure ? Yes/No
Save Current Settings as Calibrated Values 4
44
4(Activate when JC1 position 2 sets closed)
Are you sure ? Yes/No
Recall Stored Calibrated Values 4
44
4
Are you sure ? Yes/No
# : DISPLAY IN ARGB MODE ONLY
+ DISPLAY IN ARGB & COMPONENT MODE ONLY
++ DISPLAY WHEN HD-1000/-2000 CONNECTED
+++ DISPLAY IN COMPOSITE & S-VIDEO MODE ONLY
** The image orientation function is not support under the following conditions :
- PIP
- Component 1 (via CNV2 connector) input.
- Driving with 1366x768 panel
- Zoom
Firmware V1.18.00.00 or up

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 13 of 60
CONNECTORS, PINOUTS & JUMPERS
The various connectors are:
Summary: Connectors
Ref Purpose Description
CN1 Second RS-232 serial control JST 6-way, B6B-XH-A (Matching type : XHP-6)
CN3 Panel connector HIROSE DF20G-10DP-1V (Matching type : DF20A-10DS-1C)
CN6 VGA 2 input connector Hirose 12-pin, DF11-12DP-2DSA (Matching type : DF11-12DS-2C)
CN7 Audio board connector DIL socket header 5x2 right angle
(Matching audio Add-on Board P/N 416940020-3)
CN8 RS-232 serial control JST 6-way, B6B-XH-A (Matching type : XHP-6)
CN9 Ambient light sensor connector JST 3-way, B3B-PH-K (Matching type : PHR-3)
CNA1 Auxiliary power output JST 4-way, B4B-XH-A (Matching type : XHP-4)
CNA2 Auxiliary +5VDC output JST 2 way, B2B-PH-K (Matching type : XHP-2)
CNB1 Backlight inverter JST 5-way, B5B-XH-A (Matching type : XHP-5)
CNB2 Backlight status input connector JST 2 way, B2B-XH-A (Matching type : XHP-2)
CNC1 OSD controls Hirose DF13-12P-1.25H (Mating type : DF13-12S-1.25C)
(Matching OSD switch mount cable P/N 426122200-3 (150mm) or
426122210-3 (250mm)
CNV1 Alternate video in (Composite 1 & S-
Video 2)
JST 5-way, B5B-PH-K (Matching type : PHR-5)
(Matching video cable P/N 426000500-3)
CNV2 Component (YPbPr) video input
connector:
JST 6-way, B6B-PH-K (Matching type : XHP-6)
CNV5 Auxiliary video input (Composite 1&2,
S-Video 1&2)
Header pin 13x2 (Matching video cable P/N 426000800-3)
J1 S-video 1 in Mini din 4-way
J2 Composite video 1 in BNC connector
J3 Panel signal for LVDS panel JAE FI-RE51S-HF (Matching type : FI-RE51HL)

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 14 of 60
J4 HD-SDI adaptor board interface
connector
2 x 25 ways, 2.54x1.27 header
(Matching connector type : DF13-40DS-1.25C)
(Matching ribbon cable : P/N 426171100-3)
J5 Display port output for panel
connection
I-PEX 20455-030E-12 (Matching type : I-PEX 20454-030T)
J6 Panel power output for Disport port
interface panel use.
JS-1147A-08 Top 1.25mm (Matching type : Molex 51021-0800)
IR1 Infra-Red sensor connector JST 3-way, B3B-XH-A (Matching type : XHP-3)
LED1 Dual color LED connector Header pin 3x1
P1 VGA analog input DB-15 way high density 3 row
P2 DVI-I (DVI-D or VGA 2) input DVI-I connector
PP2 Power input (alternative) DC power Molex 2 pin 0.156” pitch
PP4 External panel power input Molex 43045-0400 compatible
(Matching connector type : Molex 43025-0400 compatible)
(Matching power cable : P/N 426013700-3)
PP5 Power input Molex 43650-0200 compatible
(Matching connector type : Molex 43645-
0200 compatible)
(Matching power cable : P/N 426013800-3)
Summary: Jumpers setting
Ref Purpose Note
JA3 Panel power voltage select
CAUTION: Incorrect setting can damage
panel
See panel voltage setting table 1
JA5 Panel power voltage select
CAUTION: Incorrect setting will cause panel
damage
See panel voltage setting table 1
JA6 Panel power voltage select
CAUTION: Incorrect setting will cause panel
damage
See panel voltage setting table 1
JB1 Backlight brightness voltage range 1-2 closed = 5V max
2-3 closed = 3.3V max
JB2 Backlight inverter on/off control – signal
level
2-3 = On/Off control signal ‘High’ = +5V
1-2 = On/Off control signal ‘High’ = +3.3V
Open = On/Off control signal ‘High’ = Open collector
CAUTION: Incorrect setting can damage inverter.
JB3 Backlight inverter on/off control – polarity 1-2 = control signal ‘high’ = CCFT ON
2-3 = control signal ‘low’ = CCFT ON
JB4 GPIO pins voltage selection 1-2 = 3.3V
2-3 = 5V
JB5 Backlight control type selection 1-2 = VR/Digital switch mount control
3-4 = Analog backlight brightness - voltage range 0~5V
5-6 = PWM (Pulse Width Modulation) brightness
JB7 Backlight control voltage on CNB1 pin 4
(Function when JB5 sets 1-2 closed)
Open = For OSD switch mount control (Default)
1-2 = 0V
2-3 = 3.3V / 5V controlled by JB1
JC1 Custom configuration Position 1 :
Closed = Disable B/L setup menu
Position 2 :
Closed = Enable save Current Settings as Calibrated
Values on OSD menu
Position 3 :
Closed = Enable baud rate selection function in
programming mode
Position 4 :
Closed = Hide “Reset to Factory Defaults” and “Reset to
Factory Defaults with (Color Temp.)” from OSD menu.
Position 7 :
Closed = Enable for selection of the “RM-DN5
Assembly” menu on Programming mode.
JC2 Custom configuration Position 1 : Enable J3 – pin 16 (OP1) controlled by JB4
Position 2 : Enable J3 – pin 17 (OP2) controlled by JB4
JP4 Custom configuration 1-2 closed = Reserved
3-4 closed = On-board programming
5-6 closed = Reserved
JP6 Input power control Short = External switch control
Open = Switch mount control
JP9 Factory use Default Open

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 15 of 60
JT1 Composite video-in terminator enable Open = composite video 1 input is not terminated
Close = composite video 1 input is terminated with 75
Ω
JT2 S-Video luma-in terminator enable Open = S-video 1 luma input is not terminated
Close = S-video 1 luma input is terminated with 75
Ω
JT3 S-Video chroma-in terminator enable Open = S-video 1 chroma input is not terminated
Close = S-video 1 chroma input is terminated with 75
Ω
JT4 Component luma-in terminator enable Open = S-video 2 luma input is not terminated
Close = S-video 2 luma input is terminated with 75Ω
JT5 Component Cr-in terminator enable Open = S-video 2 chroma input is not terminated
Close = S-video 2 chroma input is terminated with 75
Ω
JT6 Component Cb-in terminator enable Open = composite video 2 input is not terminated
Close = composite video 2 input is terminated with 75
Ω
SW3 Panel & function selection See table 2
SW4 Panel & function selection See table 3

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 16 of 60
Table 1 : Panel voltage setting table :
Input voltage via
PP2, PP5 Panel Voltage JA3 JA5 JA6 Jumper on board
12VDC
3.3V 3V3 closed 1-3 & 2-4 1-3 & 2-4
5V 5V closed 1-3 & 2-4 1-3 & 2-4
12V OPEN 1-3 & 2-4 5-7 & 6-8
CAUTION: Incorrect setting can damage panel & controller
Input voltage via
PP2, PP5 Panel Voltage JA3 JA5 JA6 Jumper on board
24VDC**
3.3V 3V3 closed 1-3 & 2-4 1-3 & 2-4
5V 5V closed 1-3 & 2-4 1-3 & 2-4
12V 12V closed 1-3 & 2-4 3-5 & 4-6
18V 18V closed 1-3 & 2-4 3-5 & 4-6
CAUTION: Incorrect setting can damage panel & controller
** Ensure that the backlight inverter supports 24V operation prior to connecting a 24VDC input.
Because CNA1 pin 1 and CNB1 pin 2 will output 24VDC if input 24VDC via PP2/PP3 or PP5.

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 17 of 60
Input voltage via
PP4 Panel Voltage JA3 JA5 JA6 Jumper on board
3.3 / 5 / 12 /
18VDC*
3.3V OPEN 3-5 & 4-6 1-3 & 2-4
5V OPEN 3-5 & 4-6 1-3 & 2-4
12V OPEN 3-5 & 4-6 3-5 & 4-6
18V OPEN 3-5 & 4-6 3-5 & 4-6
* Maximum current for 3.3V, 5V = 7A, Maximum current for 12V = 5A, Maximum current for 18V =
3.5A

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 18 of 60
JA3, JA5 & JA6 location on board : (Please pay attention to the jumper settings on JA3, JA5
& JA6 which are red in color)
!
!
JA3
JA6
& JA5

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 19 of 60
Table 2 : DIP Switch selection – SW3
Pos #1 Pos #2 Pos #3 Pos.#4 Description Panel resolution
For WUXGA panels
OFF ON ON OFF LG LM260WU1-SLB1 1920x1200
ON ON ON OFF LG LM240WU2-SLA1 1920x1200
OFF OFF OFF OFF Sharp LQ445D3LZ19 1920x1080
ON OFF OFF OFF Samsung LTA460H2-L02 1920x1080
OFF ON OFF OFF Sharp LQ170M1LZ04 1920x1200
ON ON OFF OFF Samsung LTA700HH-LH1 (1
st
trial testing) 1920x1080
OFF OFF ON OFF Samsung LTA700HH-LH1 (2
nd
trial testing) 1920x1080
OFF OFF ON ON AU Optronics P645HW03 V0 (1920x1080) 1920x1080
OFF OFF ON ON AU Optronics P645HW03 V0 1920x1080
For UXGA panels
OFF OFF OFF OFF Fujitsu FLC59UXC8V-02A 1600x1200
ON OFF OFF OFF Samsung LTM213U6-L01 1600x1200
For WXGA panels
OFF OFF OFF OFF LG LC420W02-A4 1366x768
ON OFF OFF OFF Sharp LQ315T3LZ24 1366x768
ON ON OFF OFF Samsung LTA320W2-L01 / LTA230W1-L02 1366x768
ON ON ON ON NEC NL12876BC26-21 / Samsung LTM170W1-L01 1280x768
OFF ON ON ON CHI MEI N154I4-L01 1280x800
OFF OFF ON OFF AU Optronics M190PW01 1440x900
OFF OFF ON ON Sharp LQ072K1LA03 1280x768
For SXGA panel
OFF OFF OFF OFF Sharp LQ181E1LW31 1280x1024
ON OFF OFF OFF AU Optronics M170EN05 1280x1024
For XGA panel
OFF OFF OFF OFF Sharp LQ150X1LGN2A 1024x768
Sharp LQ150X1LGB1 1024x768
For SVGA panel
OFF OFF OFF OFF Sharp LQ121S1DG11/41 800x600
Toshiba LTM08C351 800x600
For WVGA panel
OFF OFF OFF OFF NEC NL8048BC24-01 800x480
ON OFF OFF OFF Kyocera TCG085WV1AB-G00 800x480
ON OFF ON OFF Sharp LQ070Y3LG4A 800x480
For VGA panel
OFF OFF OFF OFF Sharp LQ104V1DG51 640x480
ON OFF OFF OFF Sharp LQ104V1DG21 640x480
Kyocera TCG075VG2AC-G00 640x480
Others
OFF ON OFF OFF AU Optronics M201EW02 V8 1680x1050
ON OFF OFF ON Samsung LTM201M1-L01 1680x1050
OFF OFF ON OFF Samsung LTI430LA01 1920x480
OFF ON ON OFF NEC NL10260BC19-01D 1024x600
ON ON ON OFF AU Optronics M200RW01 1600x900
Samsung LTM200KP01 1600x900
Remark : The above panel timings are generated based on the panel specification. Some of
the panel timings settings may not exactly to match the panel model we specified in this table.
Pos #5 Pos #6 Pos #7 Description
OFF OFF OFF WUXGA
ON OFF OFF UXGA
OFF ON OFF SXGA
ON ON OFF WXGA
OFF OFF ON XGA
ON OFF ON SVGA
OFF ON ON VGA
ON ON ON WVGA / Others
Pos. #8 Video lock ON – Disable : Always fix the output be 60Hz.
OFF – Enable : The output refresh rate locks to the input for 50Hz / 60Hz mode
(other resolution lock the output be 60Hz. )

Specifications subject to change without notice
© Digital View Ltd – Doc Ver 4.0: 15 Aug, 2016 (SVH-1920v2_manual.doc) Page 20 of 60
Table 3 : DIP switch selection – SW4
Pos. # Function Description
1 Reserved Reserved
2 Panel pixel format OFF : Double Pixel
ON : Single Pixel
3 Panel selection Default ON : Single / Double pixel LVDS panel (controlled by SW4
position 2)
4 LVDS data mapping select
(Refer to Table 2)
If SW4 position 5 = OFF (8 bit)
OFF : Mapping B
ON : Mapping A
Please adjust to get the correct picture. See as Appendix I for details of
mapping of A and B.
If SW4 position 5 = ON (10 bit)
OFF : JEIDA (LVDS panel)
ON : VESA (LVDS panel)
Please adjust to get the correct picture. See as Appendix I for details of
mapping of VESA and JEIDA.
5 Output LVDS display mode selection OFF : 8 bit
ON : 10 bit
6 LVDS mapping swap OFF : Normal
ON : Swap