Emerson Bettis RP4AF User manual

Bettis RTS Relay Board (RP4AF)
Electric Actuator
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0
June 2021

Revision Details
June 2021
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0
Revision Details
No. Date Version Type of Change
1 June 2021 0 General update
(Migration to new template)
Revision Details

i
Table of Contents
June 2021
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0
Table of Contents
Table of Contents
Section 1: Tools
Tools.........................................................................................................................1
Section 2: Material
Material.....................................................................................................................2
Section 3: Installation
Installation................................................................................................................3
Section 4: Programming
Programming............................................................................................................7

Notes
June 2021
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0
This page is intentionally left blank

June 2021
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0
1Tools
Section 1: Tools
1
Section 1: Tools
! WARNING
Remove all power supplies before doing the exchange. Act always with caution during
the exchange!
• Needle nose pliers
• Screw driver phillips
• Screw driver at
• Allen key 5
• Socket wrench 5
Figure 1

June 2021
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0 Rev. 0
2Material
Section 2: Material
2
Section 2: Material
• 1x relay board RP4AF (ID:15772)
• 2x steel screw M3x16 (ID:952)
• 3x plastic distance 8 mm (ID:9896)
• 1x plastic screw M3x15 (ID:9895)
• 1x plastic nut M3 (ID:7084)
• 2x lock plates M3 red (ID:13674)
Figure 2
Figure 3

June 2021
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0
3Installation
Section 3: Installation
3
Section 3: Installation
Unscrew the 4 hexagon socket screws from the cover and remove it carefully. Mind the
connection cable between display and logic board.
Figure 4
Unscrew the 4 cross recessed screws from the existing logic board and afterwards tilt it
carefully to you.
Figure 5

June 2021
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0 Rev. 0
4Installation
Section 3: Installation
4
Remove the cable with the 10-pole connector and connect it with the relay board.
Figure 6
Insert plastic screw M3x15 in provided hole and add plastic distance on it, after connect the
relay board with the logic board on suitable connector. Add plastic nut on plastic screw to
x the board.
Figure 7

June 2021
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0
5Installation
Section 3: Installation
5
Put two plastic distances 8 mm between logic and relay board, insert the M3x16 steel
screws through the estimated holes in logic board, plastic distances and relay board and
secure the screws with the red lock plates.
Figure 8
Install die logic + relay board back to the control (two small screws for original installation
will remain). Take care of possible damage of cables or other parts.
Figure 9

June 2021
Installation, Operation and Maintenance Manual
VCIOM-15749-EN Rev. 0 Rev. 0
6Installation
Section 3: Installation
6
Connect cable between display cover and logic board. Perform a Firmware update now,
before installing display cover on the unit. This update is important for the following
programming steps (use FW version display 1507, logic 219 or higher). For a detailed
description on how to perform a rmware update, please refer to separate manual.
During display cover installation, pay attention to the O-ring which must be sit correct
between cover and housing and x it with the 4 hexagon socket screws.
Figure 10