Dimastech mini v.2.0 User manual

DimasTech MINI
Version 2.0
ASSEMBLY MANUAL

CONTENTS OF THE KIT

ASSEMBLY DimasTec Mini V.2.0 - FLEX-FAN
- Align VC058 (7) to BT2501 (6)
and fasten wit No.1 screw
VC047_M4x10 (20), as s own
in Figure 1
- Align FAN 120 (item not
included) to BT2501 (6) on
vertical oles and fasten wit
No.2 screws VC050_M2,5x25
(21) plus No.2 knurled nuts
VC034_M2,5 (22), as s own in
figure 2
- It is possible to mount t e FLEX-
FAN in any of t e 6 oles wit M4
t readed inserts at your disposal
according to t e mot erboard you
ave purc ased or t e preferred
c oice, as s own in t e figure
beside. T e image as t e sole
purpose of illustrating t e possible
positions of t e parts.
Note: T e number indicated in t e
brackets indicates t e
corresponding identification in t e
table on t e page No.2

ASSEMBLY DimasTec Mini V.2.0 – STEP-1
- Assemble No.4 VC067_rubber-
feet_M4 (8) into t e dedicated M4
t readed inserts, located at t e base
of t e DIMAS_100_C_RF-RB_V.2.0
(1) body, as s own in t e figure
beside
ASSEMBLY DimasTec Mini V.2.0 – STEP-2
- Unscrew t e 4 screws
VC048_M3x10 oused in t e front
part of t e DimasTec Mini V.2.0
and extract t e two preassembled
components DIMAS_23 (3) and
DIMAS_24 (4), as s own in t e
figure beside
Note: T e number indicated in t e brackets indicates t e corresponding
identification in t e table on t e page No.2

ASSEMBLY DimasTec Mini V.2.0 – STEP-3
- T e DIMAS_23 component (3) as t e
possibility of ousing No.2 optical
readers inside it (items not included),
t e image as t e sole purpose of
illustrating t e possible positions of t e
parts.
- Align t e side oles of t e optical
reader wit t e slots of t e DIMAS_23
component (3) and fasten wit No°4
screws VC049_M3x6 (19) for eac
optical reader, as s own in t e figure
beside.
ASSEMBLY DimasTec Mini V.2.0 – STEP-4
- T e DIMAS_24 component (4) as t e
possibility to ouse inside No.3 ard-
disks (items not included), t e image
as t e sole purpose of illustrating t e
possible positions of t e parts.
- Insert No.12 VC019 (14) into t e
appropriate s aped slots
- Align t e side oles of t e ard-disk to
t e oles of VC019 (14) and fasten
wit No.4 screws VC014_6-32 (15) for
eac ard-disk, as s own in t e figure
beside.
Note: T e number indicated in t e brackets indicates t e corresponding
identification in t e table on t e page No.2

ASSEMBLY DimasTec Mini V.2.0 – STEP-5
- Insert t e components
DIMAS_23 (3) and DIMAS_24 (4)
wit t e respective ardware
installed, inside t e front of t e
DimasTec Mini V.2.0 and fasten
wit t e No.4 screws
VC048_M3x10 previously
extracted, as s own in t e figure
beside.
T e image as t e sole purpose
of illustrating t e possible
positions of t e parts.
ASSEMBLY DimasTec Mini V.2.0 – STEP-6
- Align t e slots at t e base of t e
BT045-2013 component (5) wit
t e slots at t e back of t e
DimasTec Mini V.2.0 and fasten
wit No.2 screws VC047_M4x10
(15) plus No.2 knurled nuts
VC024_M4 (17), as s own in t e
figure beside
Note: T e number indicated in t e brackets indicates t e corresponding
identification in t e table on t e page No.2

ASSEMBLY DimasTec Mini V.2.0 – STEP-7
- T e DimasTec Mini V.2.0 as
t e possibility of ousing No.1
power supply (PSU) inside (item
not included), t e image as t e
sole purpose of illustrating t e
possible positions of t e parts.
- Align t e oles of t e power
supply wit t e corresponding
DimasTec Mini V.2.0 oles and
fasten wit No.4 screws VC066_6-
32 (18), as s own in t e figure
beside.
OVERVIEWING IMAGE IS INDICATIVE OF AN INCORRECT MOUNTING
It is necessary, for a correct assembly, t at t e power supply (PSU) is inserted
inside t e DimasTec Mini V.2.0 only if t e body DIMAS_100_C_RF-RB_V.2.0 (1)
and t e plan DIMAS_100_P_V.2.0 (2) are assembled, ot erwise before
proceeding wit STEP-7 it is necessary to install t e DIMAS_100_P_V.2.0 plan
(2)
Note: T e number indicated in t e brackets indicates t e corresponding
identification in t e table on t e page No.2

ASSEMBLY DimasTec Mini V.2.0 – STEP-8
- T e DimasTec Mini V.2.0 as t e
possibility to mount No.9 spacers
VC016_EasyGo_M3_25mm (13) in
any of t e No.9 t readed oles M3
available to you according to t e type
of mot erboard you ave purc ased
or to your favorite arrangement , t e
image as t e sole purpose of
illustrating t e possible positions of
t e parts.
- Align t e spacers
VC016_EasyGo_M3_25mm (13) to
t e corresponding M3 t readed
oles of t e DimasTec Mini V.2.0
and fastem, as s own in t e figure
beside
ASSEMBLY DimasTec Mini V.2.0 – STEP-9
- Align t e oles in t e
mot erboard (item not included)
wit t e spacers
VC016_EasyGo_M3_25mm (13),
to fasten t e mot erboard just a
slig t downward pressure as
s own in t e figure opposite, t e
image as t e sole purpose of
illustrating t e possible positions
of t e parties.
Note: T e number indicated in t e
brackets indicates t e
corresponding identification in t e
table on t e page No.2

ASSEMBLY DimasTec Mini V.2.0 – STEP-10
- T e DimasTec Mini V.2.0 as
t e additional possibility to mount
No.1 ard-disk and No.1 SSD disk
(items not included) on t e sides
of t e body according to t e
layout you prefer, t e image as
t e sole purpose to illustrate t e
possible positions of t e parts.
- Before proceeding wit t e
assembly of t e ardware parts, it
is necessary to extract t e
DIMAS_23 (3) and DIMAS-24
components (4) as s own in STEP-
2 and STEP-5.
- Insert No.4 VC019 (14) into t e
appropriate s aped slots c osen
according to t e type of ardware
to be used.
– Align t e oles in t e base of
t e SSD disk wit t e oles in
VC019 (14) and fasten wit No.4
screws VC013_M3 (16), as s own
in figure 1.
- Align t e oles in t e base of t e
ard-disk wit t e oles in VC019
(14) and fasten wit No.4 screws
VC014_6-32 (15), as s own in
figure 2.
Note: T e number indicated in t e brackets indicates t e corresponding
identification in t e table on t e page No.2

ASSEMBLY DimasTec Mini V.2.0 – PD001_16mm
– Unscrew t e exagon nut of t e
pus button PD001_16mm (9), as
s own in Figure 1
- Before proceeding wit t e assembly
of t e ardware parts, it is necessary
to extract t e DIMAS_23 (3) and
DIMAS-24 components (4) as s own in
STEP-2 and STEP-5.
- Align No.2 PD001_16mm (9) to t e 2 vertical oles in t e front of t e body
DIMAS_100_C_RF-RB_V.2.0 (1) and fasten wit t e previously unscrewed
exagon nuts, as s own in Figure 2
Note: T e number indicated in t e brackets indicates t e corresponding
identification in t e table on t e page No.2

ASSEMBLY DimasTec Mini V.2.0 – PD001_16mm
For power ON or reset function, connect wit out
polarity yellow cable to "NO1" and ot er Yellow
cable to "C1", t an to use t e pus button
integrated LED, connect t e black cable to "-"
and t e red cable to "+", pus button integrated
LED will work wit PWLED (power on LED) and
HDLED ( ard disk LED), please take care of
polarity, follow "-" and "+" on mot erboard
instruction.
Note: T e number indicated in t e brackets indicates t e corresponding
identification in t e table on t e page No.2