Dimplex LA MI User manual

LAMI
Settings
Function
&
ProgrammingOverview
8/60381/0 1

Index
•Page3–ClockAdjustment
–HydraulicConfiguration
•Page6–PreConfiguration
–HydraulicConfiguration
•Page13–SystemSetting
–Heating&DHWsettings
2
•Page18–HeatPumpRun
–HPOn/Runningcommand
•Page20–Mode&Heaters
–Operationmodesandinline
heateroperation
•Page25–TimerFunction
–Settingtheadvancedtimer
function.

SettingTheTime
3

SettingTheClock–Time
•USINGTHEREDOUTLINED
AREAS&BUTTONS
•ENSUREGREENLEDISOFF
•CLOCKBUTTON
•SETBUTTON
•▲UPBUTTON
•▼DOWNBUTTON
PRESSCLOCKBUTTONFOR5
SECONDSTOENTERCLOCKSET
MENU
CONTINUEDBELOW
HEAT
TANK
QUITE
HEATER
FORCE
OPERATION
ACTUAL
HEATER
BOOSTER
TIMER OUTDOOR
WATER OUTLET
OFF / ON Ф
TIMER
OFF/ON
CLOCK
▲
▼
SET
SELECT
CANCEL
SETTING
MODE
QUITE
ERROR
RESET
CHECK
HEATER
FORCE
SEARCH
PUMPDW
STATUS
SETTING
STATUS
PUMPDW
18 °c
25°c
SOLAR REMOTE
MON
08:30
4

SettingTheClock
Sets the current day of the week.
M O N – Sets Monday as the day of the week.
Sets the current hour of the day.
0 8 : – Set 8 am as the hour of the day.
Sets the minute past the hour.
: 3 0 – Set 30 minutes past the hour.
5
STEP 2 –SETTING THE HOUR
H O U R Flashes
Press ▲▼
Select Hour 0 8 :
Press S E T
See STEP 3
STEP 1 –SETTING THE DAY
D A Y Flashes
Press ▲▼
Select Day ReqdM O N,
Press S E T
See STEP 2
STEP 3 – SETTING THE MINUTES
MINUTES Flash
Press ▲▼
Select Minutes : 3 0
Press S E T
COMPLETED

PreConfiguration
6

PreConfiguration–HydraulicSetUp
•USINGTHEREDOUTLINED
AREAS&BUTTONS
•ENSUREGREENLEDOFF
•CHECK&SETBUTTONS
•SELECTBUTTON
•▲UPBUTTON
•▼DOWNBUTTON
•CANCELBUTTON
PRESSSET&CHECKBUTTONS
SIMULTANEOUSLYFOR5SECONDSTO
ENTERPRECONFIGURATIONMENU
CONTINUEDBELOW
HEAT
TANK
QUITE
HEATER
FORCE
OPERATION
TIMER OUTDOOR
WATER OUTLET
OFF / ON Ф
TIMER
OFF/ON
CLOCK
▲
▼
SET
SELECT
CANCEL
SETTING
MODE
QUITE
ERROR
RESET
CHECK
HEATER
FORCE
SEARCH
PUMPDW
STATUS
SETTING
STATUS
PUMPDW
■
■
18°c
25°c
MON
08:30
ACTUAL
HEATER
BOOSTER
■
■
■
7

OPTION 3 – HOT WATER PREPARATION – NO
TANK █, con
Press SELECT
Press ▲▼
Display NO
Press S E T to Store
Option 4 Press▼
OPTION 2 – ROOM THERMOSTAT – YES
HEAT █, room, con
Press SELECT
Press ▲▼
Select YES
Press S E T to Store
Option 3 Press▼
OPTION 1 – ROOM THERMOSTAT – NO
HEAT █, room, con
Press S E L E C T
Press ▲▼
Select N O
Press S E T to Store
Option 2 Press▼
PreConfiguration–HydraulicDesign
Is the heat pump interlocked with a room thermostat.
(Horstmann PRT1)
Either NO or YES as Indicated in OPTION 2.
N O - There is no room thermostat proving heat pump
interlocking, the heating will be regulated by flow
temperature.
Is the heat pump interlocked with a room thermostat.
(Horstmann PRT1)
Either NO or YES as Indicated in OPTION 1.
Y E S - the heat pump is interlocked with a room thermostat
proving the heat pump with a demand signal.
Is the heat pump preparing hot water via a suitable hot
water cylinder & temperature sensor.
Either NO or YES as indicated in OPTION 4.
NO - the heat pump is not preparing hot water.
8

OPTION 6 – SPACE HEATING PRIORITY
HEAT █, PrY
Press SELECT
Press ▲▼
Display NO
Press S E T to Store
Option 7 Press▼
OPTION 5 – SPACE HEATING PRIORITY
HEAT █, PrY
Press SELECT
Press ▲▼
Display YES
Press S E T to Store
Option 6 Press▼
OPTION 4 – HOT WATER PREPARATION – YES
TANK █, con
Press SELECT
Press ▲▼
Display YES
Press S E T to Store
Option 5 Press▼
PreConfiguration–HydraulicDesign
Is the heat pump preparing hot water via a suitable hot
water cylinder.
Either NO or YES as Indicated in OPTION 3.
Y E S - the heat pump is preparing hot water and is
connected to a suitable heat pump hot water cylinder.
Is space heating to be given priority.
Either NO or YES as Indicated in OPTION 6.
Y E S - the heat pump gives priority to space heating.
Hot water will only be prepared once the space heating
demand is satisfied.
Is space heating to be given priority.
Either NO or YES as Indicated in OPTION 5.
N O - the heat pump gives priority to hot water preparation
based upon the following settings, OPTION 7 & OPTION 8
Below.
9

OPTION 9 – BOOSTER HEAT DELAY TIME
BOOSTER █,00:00, dLY
Press SELECT
Press ▲▼
Set Duration 1 : 3 0
Press S E T to Store
Option 10 Press▼
OPTION 8 – TANK HEATING INTERVAL SET
HEAT █,00:00, int.
Press SELECT
Press ▲▼
Set Duration 1 : 3 0
Press S E T to Store
Option 9 Press▼
OPTION 7 – SPACE HEATING INTERVAL SET
TANK █,00:00, int.
Press SELECT
Press ▲▼
Set Duration 1 : 0 0
Press S E T to Store
Option 8 Press▼
Sets a delay period during simultaneous space heating and
hot water demands. Space heating remains covered during
this period. The heat pump switches over to hot water
priority once the time period has elapsed.
1 : 0 0 – Sets a 1hr delay. Space heating continues to be
met for 1hr before the hot water demand is covered.
PreConfiguration–HydraulicDesign
Sets the maximum time period hot water preparation will be
covered. Switching back over to cover the space heating
demands.
1 : 3 0 – Sets a 1hr time period when hot water preparation
is terminated and the space heating request is covered.
Sets the maximum time the heat pump will prepare hot
water for before turning on the cylinder immersion heater to
achieve the desired cylinder temperature.
1 : 3 0 – Sets a 90 minutes time period before the cylinder
immersion switches on to complete the hot water request.
10