Directed 4105A User manual

Owner's Guide
Models
4105V, 4105P
4105X, 4105A
4105L
G4105 2015-11

iii
© 2015 Directed. All rights reserved.
Congratulations
Congratulations on the purchase of your state-of-the-art keyless entry
and remote start system. Reading this Owner’s Guide prior to using
your system will help maximize the use of your system and its many
features. For more information please visit us online (see back cover
for URL). For any additional questions please contact your authorized
Directed dealer or contact Directed at 1-800-753-0600. (U.S. only) or
1-800-361-7271 (Canada only). Additional support is also available
at: http://support.directed.com
Your Warranty
Your system comes with a warranty. The warranty terms are detailed at
the end of this guide. Make sure that you receive the proof of purchase
from your dealer, indicating the product was installed by an authorized
Directed dealer.
Replacement remote controls
Please see your authorized dealer or visit us at www.directedstore.com
to order additional remote controls. Remote control part numbers are
found on the back of the device.

iv © 2015 Directed. All rights reserved.
Important information
Government Regulations and Safety information
Read the Government Regulations and Warning! Safety
First sections of this manual prior to operating this system.
Warning! Failure to heed this information can result in
death, personal injury or property damage and may also
result in the illegal use of the system beyond its intended
purpose.
This product is designed for fuel injected, automatic trans-
mission vehicles only. Use of this product in a standard
transmission vehicle is dangerous and contrary to the
product’s intended use.

Contents
Congratulations ................................................................................................i
Your Warranty...........................................................................................i
Replacement remote controls .......................................................................i
Important information ........................................................................................ii
Government Regulations and Safety information ..........................................ii
Remote Control .................................................................................................3
Remote control functions.....................................................................................3
Standard configuration..............................................................................3
Using the system .............................................................................................5
Locking....................................................................................................5
Unlocking ................................................................................................5
Disabling (optional) Starter Kill ..................................................................5
Panic Mode .............................................................................................6
Remote Start.............................................................................................6
Key Takeover............................................................................................7
Safety Features.........................................................................................8
Pit Stop....................................................................................................8
Car Finder ...............................................................................................9
Optional Starter Anti-Grind Circuitry ...........................................................9
Disabling the Remote Start System ..............................................................9
Remote Programming ......................................................................................10
Programming Options......................................................................................11
Rapid Resume Logic .......................................................................................11
Battery Information..........................................................................................12
Replacing the Battery ..............................................................................12
Battery Disposal .....................................................................................12
Patent Information ...........................................................................................13
Government Regulations ..................................................................................14
Warning! Safety first .......................................................................................15
Remote Start Capable .............................................................................15
Interference............................................................................................16
Upgrades ..............................................................................................16
Water/Heat Resistance ...........................................................................16
Limited lifetime consumer warranty ....................................................................17

3
© 2015 Directed. All rights reserved.
Remote Control
Feature Description
Internal Antenna Used for transmitting information
Transmit LED Active when transmitting information
Command buttons (4)
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
Used to perform:
Locking
Unlocking
Remote Start
Silent mode/Auxiliary channel
Remote control functions
The remote buttons are used to send commands to the system. The but-
tons indicated below are for standard configuration.
Standard configuration
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
Button
The lock function is controlled by pressing
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
on the remote control
for one second. When held for approximately two seconds, Panic is
activated.
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replacebatter y and then snap case together.
Button
The unlocking function is controlled by pressing
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
on the remote con-
trol for one second. You can also turn Panic off with this button.

4© 2015 Directed. All rights reserved.
Button
Silent Mode™and an optional auxiliary function are controlled by
pressing . Silent Mode works by pressing for less than one
second before locking or unlocking. An optional auxiliary function such
as trunk release may be controlled by pressing and holding for
approximately two seconds.
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
Button
The remote start function of your system is controlled by pressing this
button for one second.
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and Buttons
Car Finder is controlled by pressing these two buttons.
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and Buttons
When simultaneously pressed these buttons control the optional rear
window defogger during remote starting. The parking lights flash three
times to confirm activation. Once activated the defogger will turn on
whenever the vehicle is remote started.
The parking lights flash twice when the defogger is deactivated. The
defogger does not turn on when the vehicle is remote started.
Important note: Defogger is an optional feature. Additional parts and
labor may be required. See your Directed dealer for details.
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replacebatter y and then snap case together.
Buttons
Timer mode is activated when these buttons are pressed simultaneously.
When you activate timer mode the parking lights flash four times, after a
one second delay the engine starts. To turn the engine off, without exiting
timer mode press the
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
.

5
© 2015 Directed. All rights reserved.
The system remains in timer mode and will start every three hours for a
maximum of six starts unless cancelled by turning on the ignition, or by
activating any of the shutdown inputs to the system.
The parking lights flash four times indicating timer mode is exited.
Using the system
Locking
Pressing
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replacebattery and then snap case together.
for one second locks the system (if the door locks are con-
nected). The horn honks and the parking lights flash once to confirm the
system is locked. The Failsafe®Starter Kill also activates and prevents
the vehicle’s starter from cranking.
Important note: Horn honk and Failsafe are both optional features.
Unlocking
Pressing
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replacebattery and then snap case together.
for one second unlocks the doors (if connected). The horn
honks twice and the parking lights flash twice to confirm unlocking of
the system. The Failsafe Starter Kill is deactivated.
Disabling (optional) Starter Kill
If your remote control is lost or damaged, you can manually override
the starter kill. To do this, you must have the vehicle's ignition key and
know where the Valet button is located. Be sure to check with the in-
staller for the location of the Valet button.
To override the starter kill, turn the ignition on and press and release the
valet button within10 seconds. The vehicle should start. If it does not
start, you may have waited too long; turn the ignition off and repeat
the process.

6© 2015 Directed. All rights reserved.
Location of Valet button: ____________________
Panic Mode
If you are threatened in or near your vehicle, you can attract atten-
tion by triggering the system with your remote control. Press
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
for
approximately two seconds to enter Panic Mode. In Panic Mode, the
horn will honk and the parking lights will flash for 30 seconds. To stop
Panic Mode at any time, press
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
, or
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
on the remote control.
Note: In order for Panic Mode to be effective, the vehicle’s horn (or
optional siren) and the vehicle's parking lights must be connected.
Remote Start
This feature allows you to remotely start and run your vehicle for a
programmable period of time. This makes it possible to warm up the
engine, and adjust the interior temperature of the vehicle with the cli-
mate control system. If interior heating or cooling is desired, the climate
controls must be preset, and the fan blower must be set to the desired
level prior to remote starting the vehicle.
Satmode,
bank selector
AUDIO
PWR
12
REWFF
PLAY/PROG NR
3456
DISC- DISC+
11:53
XM1-1 CH-001
CH
VOL
SCAN SOUND
AM/FM
CD/AUX
SAT
RADIO
SEEK
SKIP
RPT
DISP -
MODE
A.SEL
RDM
TUNE
AUTO
OFF
DUAL
A/C MODE
Channel control
Category
Control
Text selector.
Hold for 10secto toggle
channelor category
tune modes.
Toggles
Scan mode
Bank and
present
indicator
Channel
and text
indicator
Preset 1-6.
Hold until beepto
savetoapreset.
CATEGORY
Tune mode
indicator
MODE
DUAL
OFF
AUTO
MAP/
GUIDE MENU SETUP
INFO ZOOM CANCEL AUDIO
AUTO
MODE
A/C
LOAD
DISC
TAPE AM/FM DISP
MODE
SCAN RPT A.SEL/RDM-SEEK +
1234 56
DISC- DISC+
VOL
PWR
PUSH
TUNE
SOUND
PUSH
XM1-1
VOL
CH
CHANNEL
CATEGORY
NAME
TITLE
:
:
:
:
1
CH
2
CH
3
CH
6
CH
5
CH
4
CH
MODE SCAN SOUND
001-HITS1
POP
MUSICNAME
MUSIC TITLE
Channel control
Category
Control
001 014 018
040 065 115
Toggles between
channel and
category modes
Bank and
present
indicator
Upper display
text mode
selector
Sat mode
and bank
selector
Preset 1-6.
Press until
beepto save
to a preset.
Channeland text
Indicator fields
Toggles
Scan mode
Tune mode
indicator
ANTENNA
SC OUTPUT
Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator
Headunit bus cableSiriusConnect Cable
HON-SC1
Honda Bus
Compatible
Translator
Warning! (1) Never remote start your vehicle
when the keys are in the ignition, except when
performing Valet Take-Over, and (2) Never start the
vehicle if it is not in PARK or NEUTRAL
To remote start the vehicle:
1. Make sure the parking brake is set. Press the
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
button on the
remote control once* (or the amount of times the system has been
programmed to activate the remote start).
2. The parking lights flash to confirm that the vehicle is attempting to
start. In gasoline vehicles the engine will start 4 seconds after the

7
© 2015 Directed. All rights reserved.
parking lights flash, in diesel vehicles the engine starts after the
WAIT-TO-START timer has expired.
3. Once the vehicle has started, it will run for the pre-programmed
period of time (12, 24, or 60 minutes) or until a shutdown input
is triggered.
* The factory setting is one press but this can also be programmed for
two or three presses maximum (See your authorized Directed installer
for the amount of presses programmed).
Record the number of presses to activate remote start here:____
Satmode,
bank selector
AUDIO
PWR
12
REWFF
PLAY/PROG NR
3456
DISC- DISC+
11:53
XM1-1 CH-001
CH
VOL
SCAN SOUND
AM/FM
CD/AUX
SAT
RADIO
SEEK
SKIP
RPT
DISP -
MODE
A.SEL
RDM
TUNE
AUTO
OFF
DUAL
A/C MODE
Channel control
Category
Control
Text selector.
Hold for 10secto toggle
channelor category
tune modes.
Toggles
Scan mode
Bank and
present
indicator
Channel
and text
indicator
Preset 1-6.
Hold until beepto
savetoapreset.
CATEGORY
Tune mode
indicator
MODE
DUAL
OFF
AUTO
MAP/
GUIDE MENU SETUP
INFO ZOOM CANCEL AUDIO
AUTO
MODE
A/C
LOAD
DISC
TAPE AM/FM DISP
MODE
SCAN RPT A.SEL/RDM-SEEK +
1234 56
DISC- DISC+
VOL
PWR
PUSH
TUNE
SOUND
PUSH
XM1-1
VOL
CH
CHANNEL
CATEGORY
NAME
TITLE
:
:
:
:
1
CH
2
CH
3
CH
6
CH
5
CH
4
CH
MODE SCAN SOUND
001-HITS1
POP
MUSICNAME
MUSIC TITLE
Channel control
Category
Control
001 014 018
040 065 115
Toggles between
channel and
category modes
Bank and
present
indicator
Upper display
text mode
selector
Sat mode
and bank
selector
Preset 1-6.
Press until
beepto save
to a preset.
Channeland text
Indicator fields
Toggles
Scan mode
Tune mode
indicator
ANTENNA
SC OUTPUT
Sirius-Ready, SAT Radio Ready or select OEM headunits with optional Honda Bus Compatible Translator
Headunit bus cableSiriusConnect Cable
HON-SC1
Honda Bus
Compatible
Translator
Warning! It is unsafe to operate a vehicle’s motor in a
garage or other closed off area. Breathing the exhaust
from the vehicle is hazardous to your health. Never
activate the remote start in an enclosed space.
Key Takeover
When you are ready to drive the vehicle:
1. Unlock the doors.
2. Enter the vehicle. Do not step on the foot brake.
3. Insert the key, turn it to the run (not start) position. Step on the foot
brake. The remote start is disabled and the parking lights turn off.
4. Disengage the parking brake and begin driving.
Note If your vehicle uses a Smart Key or PTS (Push-To-Start) system,
please refer to the vehicle specific instructions included with
the owner's guide of the interface module or consult your
authorized dealer.

8© 2015 Directed. All rights reserved.
Safety Features
The following safety features will disable the remote start when acti-
vated or not allow the engine to start if not properly set before starting.
• Foot Brake is depressed
• Hood is opened
• Remote Start shutoff switch is OFF
• The pre-programmed run time (12, 24 or 60 minutes) has elapsed
• Remote Start activation procedure is repeated
• Parking brake is disengaged
• Engine over-rev protection (Tachometer mode only)
Pit Stop
This remote start can keep the engine running during short trips away
from the vehicle.
To enable Pit Stop mode:
1. Park in a well ventilated area.
2. With the engine running set the transmission in the park position
and ensure the parking brake is set.
3. Press and release the
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
button once (or the amount of times the
system has been programmed to activate the remote start), the
parking lights turn on to confirm.
4. Turn off the ignition and remove the key, the engine continues
running.
5. Exit and secure the vehicle, the engine runs for the programmed
runtime.
Important: This feature will not work if the brake pedal is being pressed.

Note If your vehicle uses a Smart Key or PTS (Push-To-Start) system,
please refer to the vehicle specific instructions included with
the owner's guide of the interface module or consult your
authorized dealer.
Car Finder
Car finder allows you to locate your vehicle, by having the system flash
the parking lights.
To activate:
1. Press and release the
AUX
AUX
AUX
Your 1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
and buttons at the same time.
2. The parking lights flash slowly several times, allowing you to lo-
cate your vehicle.
Optional Starter Anti-Grind Circuitry
This system includes an anti-grind circuit that can prevent damage to
the starter motor if the key is turned to the start position while the remote
start is ON.
Note: Anti-grind circuitry only works if an optional relay has been add-
ed and the remote is operating the motor.
Disabling the Remote Start System
When the Remote Start Shutoff switch is set to the OFF position, remote
engine starting is defeated. DO this when the vehicle is being serviced
or driven by someone unfamiliar with remote start system operations.
Location Of Shutdown Switch: _________________________

10 © 2015 Directed. All rights reserved.
Remote Programming
Your system comes with the remote controls already programmed, how-
ever if you are replacing or adding additional remote controls, they
must be programmed to the system prior to operating the system. To
program the remote, you need to know where the valet button is lo-
cated. If the horn honk is not connected, the main unit LED needs to be
visible for visual confirmation. If you cannot locate or access the main
unit, it is recommended that you visit your authorized dealer for remote
programming. The system is capable of accepting up to four remote
controls.
1. Turn key to the ON position
2. Within 10 seconds, press and release the valet button one time.
3. Within 10 seconds, press and hold the valet button. The LED on
the module flashes one time and the horn (if connected) honks to
confirm entry into remote programming. Do not release the valet
button.
4. Press the
AUX
AUX
AUX
Your1-way remote coin cell battery can be changed by using a small at blade screwdriver to pry case apart. Replace battery and then snap case together.
button on the remote control. The horn honks to con-
firm the remote has been programmed.
5. Release the valet button.
6. Turn the key to OFF position. The horn sounds one long honk to
confirm that remote programming has been excited.
The programming routine exits if any of the following occurs:
• The ignition is turned off
• There is no activity for 30 seconds
• The Valet button is pressed too many times

11
© 2015 Directed. All rights reserved.
Programming Options
Feature options will control your system's normal operation. Some op-
tions may require additional parts and installation labor. The following
is a list of the programmable options with the factory settings in bold.
• 12 minute to 60 minute runtime. Your system can be programmed
to allow the vehicle to run for up to 60 minutes when remote
started. This can be set up to minute increments by your installer.
• Parking lights flashing or constant. Your system can be programmed
to flash the parking lights or have them come on constantly during
the remote start operation.
• Ignition switch controlled door locking ON or OFF. With this fea-
ture on, the doors will lock 3 seconds after the ignition key is
turned on, and will unlock when the ignition key is turned off.
Important: The door lock option must be installed for the ignition
controlled door lock feature to work.
Rapid Resume Logic
This Directed system stores its current state to non-volatile memory. If the
power to the system is disconnected and then reconnected, the system
recalls the stored state from memory.

12 © 2015 Directed. All rights reserved.
Battery Information
The remote control is powered by two 3V, CR2016 batteries. When
the battery begins to weaken, operating range is reduced and the LED
on the remote control dims.
Replacing the Battery
1. Use a small flat blade screw driver and insert it into the slot located
along the bottom of the remote, near the key ring. Carefully pry
open the case.
2. Remove the old batteries from the holding clip. Orient the new
batteries for the correct polarity and insert into the holding clip.
3. Reposition the case parts, then snap together by pressing firmly
and evenly on the front and back.
Battery Disposal
Directed cares about the environment. If you need to dispose
of the battery, please do so in accordance with your munici-
pal requirements for battery disposal.

13
© 2015 Directed. All rights reserved.
Patent Information
This product is covered by one or more of the following United States
patents:
Remote Start Patents:
5,349,931; 5,872,519; 5,914,667; 5,952,933; 5,945,936;
5,990,786; 6,028,372; 6,467,448; 6,561,151; 7,191,053;
7,483,783
Vehicle Security Patents:
5,467,070; 5,532,670; 5,534,845; 5,563,576; 5,646,591;
5,650,774; 5,673,017; 5,712,638; 5,872,519; 5,914,667;
5,952,933; 5,945,936; 5,990,786; 6,028,505; 6,452,484
Other patents pending

14 © 2015 Directed. All rights reserved.
Government Regulations
This device complies with Part 15 of FCC rules. Operation is subject to the fol-
lowing two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential instal-
lation. This equipment generates and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television, which can be determined by
turning the equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
This device complies with the Industry Canada Radio Standards Specification
RSS 210. Its use is authorized only on a no-interference, no-protection basis; in
other words, this device must not be used if it is determined that it causes harm-
ful interference to services authorized by IC. In addition, the user of this device
must accept any radio interference that may be received, even if this interference
could affect the operation of the device.
Warning:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this device.

15
© 2015 Directed. All rights reserved.
Warning! Safety first
The following safety warnings must be observed at all times:
Due to the complexity of this system, installation of this product must only be per-
formed by an authorized Directed dealer.
Remote Start Capable
When properly installed, this system can start the vehicle via a command signal from the re-
mote control. Therefore, never operate the system in an enclosed area or partially enclosed
area without ventilation (such as a garage). When parking in an enclosed or partially en-
closed area or when having the vehicle serviced, the remote start system must be disabled
using the installed toggle switch. It is the user’s sole responsibility to properly handle and
keep out of reach from children all remote control devices to assure that the system does
not unintentionally remote start the vehicle. THE USER MUST INSTALL A CARBON MON-
OXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL
DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY
ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES REMAIN CLOSED. These
precautions are the sole responsibility of the user.
Use of this product in a manner contrary to its intended mode of operation may result in
property damage, personal injury, or death. (1) Never remotely start the vehicle with the ve-
hicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user
must also have the neutral safety feature of the vehicle periodically checked, wherein the
vehicle must not remotely start while the car is in gear. This testing should be performed by
an authorized Directed dealer in accordance with the Safety Check outlined in the product
installation guide. If the vehicle starts in gear, cease remote start operation immediately and
consult with the authorized Directed dealer to fix the problem.
After the remote start module has been installed, contact your authorized dealer to have him
or her test the remote start module by performing the Safety Check outlined in the product
installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit
test, the remote start unit has not been properly installed. The remote start module must be
removed or the installer must properly reinstall the remote start system so that the vehicle
does not start in gear. All installations must be performed by an authorized Directed dealer.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS

16 © 2015 Directed. All rights reserved.
CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE
START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR
PERSONAL INJURY. YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT AND SEEK
THE ASSISTANCE OF AN AUTHORIZED Directed DEALER TO REPAIR OR DISCONNECT
THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE
OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
This product is designed for fuel injected vehicles only. Use of this product in a standard
transmission vehicle must be in strict accordance with this guide. This product should not be
installed in any convertible vehicles, soft or hard top with a manual transmission. Installation
in such vehicles may pose certain risk.
Interference
All radio devices are subject to interference which could affect proper performance.
Upgrades
Any upgrades to this product must be performed by an authorized Directed dealer. Do not
attempt to perform any unauthorized modifications to this product.
Water/Heat Resistance
This product is not designed to be water and/or heat-resistant. Please take care to keep
this product dry and away from heat sources. Any damage from water or heat will void
the warranty.