Disinfect&Fog Heavy Duty ULV Fogger User manual

Heavy Duty
ULV Fogger
Ownership Manual

Heavy Duty ULV Fogger Ownership Manual
Page 1
• This product is designed only for 120V
• Protection degree: IPx4
• Replacement of fuse must be done properly and with caution to
avoid fire or error in the device.
• Consult with the disinfectant provider’s SDS sheet to determine if
Personal Protection Equipment (PPE) should be worn.
• This machine should only be operated with su!cient knowledge of
equipment before use.
• Be sure to completely read the How To Use part of this manual.
• After each use of the machine, ensure that you clean the chemical
bottle with water for 30-60 seconds. (If this action isn’t done,
blockage or damage to machine may occur)
• Ensure if the product comes into contact with water, that it is
disconnected from all power sources.
• Remove the power cord from the outlet when checking problems,
fuse, or adding disinfectant
• Keep out of reach of children
• Do not modify or attempt to open the product, this will void the
warranty.
Product Notes
Product Name: Heavy Duty ULV Fogger
Power: 1250 W motor
Weight: 3 KG
Operating Voltage: 120 V
Specifications
• Main Machine • Chemical Bottle
• Shoulder Strap • Funnel
• Fuse (extra) • User manual
• Alternate wide-angle output emitter
Product List

• Remove the cap for the bottle, add in desired amount of
disinfectant, and close cap clockwise until sealed.
• If bottle is disconnected from the main body of the fogger,
reattach by inserting until latched (top latch).
• Ensure the control knob for Disinfectant is set (turned) to the
“Close” position.
• Plug the fogger into a standard 120V outlet.
• Hold the fogger by the handle or use the should strap. Push the
progressive power slide switch to the desired position to turn on
the fogger.
• The fogger will blow air only. Slowly turn the Disinfectant knob
towards the “Open” position. The disinfectant should be seen at the
output. Refer to the Disinfect & Fog training videos for more info
on best practices using this fogger (see Resources section).
After use:
• Leaving the slide switch “on”, turn the disinfectant know to “close”,
allowing the residual disinfectant to be drained from the machine
(approx. 5-10 seconds).
• Turn o!the slide switch to turn o!the fogger.
• Push the lever at the top of the bottle (tank) to disconnect the
bottle from the fogger main body. This will release any built-up
pressure that may exist after use.
• Turn on the slide switch and ensure any residual disinfectant is
drained from the main body. Turn o!the slide switch when
completed.
• The bottle (tank) can be reconnected to the main body for next
use.
How To Use
www.disinfectandfog.com/training-videos
Resources
Heavy Duty ULV Fogger Ownership Manual
Page 2

Heavy Duty ULV Fogger Ownership Manual
Page 3
• Check whether the power cord is plugged into an outlet, and if the
outlet is functioning properly.
• Check whether the power cord jack and the power cord of the
product are connected
• Check to see if the power fuse is functioning normally.
• Check the fuse holders on the body and the back of the product
• Use the fuse with the proper capacity in replacing fuses (250v/
10A)
NOTE: It is important to perform the Maintenance procedure, as this
will usually be the major cause of no chemical outputting from the
unit.
• Check whether the chemical bottle is properly connected to the
body
• Check whether the control valve of the chemical bottle is
completely open
• Check for damage on the chemical bottle (If it is damaged,
chemical bottle replacement is recommended)
• Check whether the O-ring of connector from chemical bottle to
body of the product (if it is damaged, its rating: Internal diameter:
7.5, External diameter: 10.5)
• Check whether the large-hole nozzle cap for cleaning is in place. If
so, then replace it with the small-hole nozzle cap
If these measures fail, please contact your local service outlet or
representative.
Troubleshooting
Machine fails to operate when the power slide switch is “On”
Although the motor operates normally, the chemical isn’t sprayed.

Heavy Duty ULV Fogger Ownership Manual
Page 4
• Check whether the chemical bottle is placed correctly on the body
of the product
• Check whether the control valve and the cap of the chemical bottle
is closed completely
• Check whether the control valve of the chemical bottle is damaged
(if so, it is recommended to buy and replace the chemical bottle)
• After releasing the body of the product, check whether the pipe is
connected properly and reassemble again
• Check whether the pipe hose within the product is damaged. If so,
replace the part.
Although the motor operates normally, the chemical is sprayed
intermittently.
• When this product is not used for a long time, it should be checked
regularly and cleaned.
• Store this product in a dry environment.
• When dumping products, please send them to the recycling station
designated by the government to help protect the environment.
Maintenance & Repair

www.disinfectandfog.com
[e-mail]
1-855-561-4512