DiviNet Wice.box WB01-A User manual

WICE.box User Manual1
USER MANUAL
WICE.box MODEL NO: WB01-A
W
WICE.box
USER MANUAL

WICE.box User Manual 1
•Risk of Electric Shock. Do
Not Open
•Do Not Expose this unit to Rain
or Moisture
•No user Serviceable parts in-
side. Refer servicing to qualified
service personnel only.
CAUTION
CAUTION NOTICE
Copyright
This manual is copyrighted with all rights reserved. No
portion of this manual may be copied or reproduced by any
means.
DiviNet Access Technologies Ltd reserves the right to
revise this document and to make changes in the content
from time to time without obligation on the part of DiviNet
Access Technologies Ltd to provide notification of such
revision or change.
Trademarks
DiviNet, WICE.box, WICE.MAN, and RAMNetare
Trademarks of Divinet Access Technologies Ltd.
All other brand names, logos and trademarks mentioned in
this manual are a property of their respective owners.

WICE.box User Manual2
TABLE OF CONTENTS
Table of Contents
♦Packing List -----------------------1
♦Installation of WICE.box -----------2
♦Front Panel Controls ---------------5
♦Remote Control -------------------6
♦Trouble Shooting ------------------13
♦Technical Specifications------------14
♦Service Record --------------------15
♦Notes -----------------------------16

WICE.box User Manual 1
1. PACKING LIST
Please check the contents of the package
immediately upon opening the sealed box and before
installation. The package should contain the
following:
♦WICE.box unit
♦Remote Control
♦Audio Video Cable (AV Cable)
♦User Manual
If any of the items are found missing please contact
where it was purchased from.
Optional Accessories depending upon the model are:
♦Remote Interface Module for Keyboard
♦RF signal output for older TV sets and RF cable
♦Data Cable
♦S-Video Cable

WICE.box User Manual2
2. INSTALLATION OF WICE.box
White
RedYellow
The installation can be done only where a
WICE.MAN (RAMNet) connection is available.
Authorized personnel will do this connection. The
Fig.1 below shows the back panel of WICE.box.
This unit works on 230VAC, 50Hz power supply.
Fig.1
For televisions having AV type input, an AV cable
(provided with the kit) is connected from
“VIDEO”, “R-AUDIO-L” as show in Fig.2
Fig. 2
For televisions having only RF input, WICE.box
model with RF output is required. An RF cable is
connected from the point named “TV” to the
antenna input of the television as shown in Fig.3.
Fig.3
2. INSTALLATION OF WICE.box

WICE.box User Manual 3
2. INSTALLATION OF WICE.box
Any TV can be tuned for the WICE.box video signal
by using the “TEST SIGNAL” switch when it gives
vertical bars to TV.
Fig.4.1 (WICE.box on DSL network)
Fig.4.2(WICE.box on DSL network)
♦Input Connectivity :
For WICE.box on DSL network, as shown in Fig. 4.1,
connect the input telephone line to the splitter
(LINE). The splitter has two more ports, connect one
port (Phone) to the Telephone and the other port
(MODEM) to the DSL Modem. Both connections are
through normal twisted pair cables. Connect the
Ethernet port of the DSL Modem to the Input of
WICE.box (RAMNET port) through UTP cable. Connect
computer to the COMPUTER port (optional) of

WICE.box User Manual4
2. INSTALLATION OF WICE.box
WICE.box and AV cable to VIDEO/AUDIO ports of
WICE.box.
For WICE.box on Pure Ethernet network, as shown in
Fig. 4.2, connect the port line from Distribution Module
to the Input of WICE.box (RAMNET port) through UTP
cable. Connect computer to the COMPUTER port
(optional) of WICE.box and AV cable to VIDEO/AUDIO
ports of WICE.box.
♦Data Connectivity :
A straight UTP cable is used to connect a computer to
WICE.box. This provides data connectivity to the
computer via the RAMNet connection coming to the
WICE.box. Any standard Ethernet card (10/100Mbps)
working at 10 Mbps can be used inside the PC.
♦Video Output :
Most TV sets provide a composite video input. It can
be connected to the Video output (yellow) of the
WICE.box via the A-V cable. For old TV sets which do
not have a AV input, you may need a different model
of WICE.box which provides RF output.
♦Audio Output:
Stereo left and right channel connectors can be
connected to any stereo type audio input of a
television via the same AV cable that is used for video.
For TVs not having stereo audio input, any one audio
output (left or right) can be connected to the audio
input of the TV.
Headphone output in stereo is also available for
personal listening. You can turn down the TV volume
when using a headphone with WICE.box.
♦S-Video output :
It is a video output signal used for better picture
2. INSTALLATION OF WICE.box

WICE.box User Manual 5
quality. Some newer TV sets have an S-Video input
facility where a suitable S-Video cable can be
connected to view the picture. The same can be used
to get better picture quality from a LCD projector in a
home theatre.
Other features include:
•SURROUND SOUND (back panel)
•KARAOKE FACILITY (front panel)
Note: Some features like Surround Sound, Karaoke
Microphone input and RF output may not be active in
regular model of WICE.box.
2. INSTALLATION OF WICE.box

WICE.box User Manual6
The Remote Control of WICE.box is as shown in below.
The Main menu can be seen on the TV screen by pressing
the MENU button on the remote control. You may use the
PROG~or the PROG€ to change the current option from
the displayed list. Pressing the OK button will perform the
The front panel of WICE.box is
shown in Fig.4
Fig.5
Buttons:
MENU
When it is pressed it displays
the menu.
~~ UP
It is a menu navigation button.
To move up one item in any
menu list of options press it
once.
€DOWN
It is a menu navigation button.
To move down one item in any
menu list of options press it
once.
OK
It is used to select the current
menu option.
4. REMOTECONTROL

WICE.box User Manual 7
4. REMOTE CONTROL
ƒƒ-VOLUME DOWN
Decreases volume level.
+„„ VOLUME UP
It increases volume level.
Note : Press ƒƒ-and +„„ simultaneously to Mute the
audio. To resume the audio, press either button and set
the volume.
Main Menu options
Channels
1.Go to CHANNELS option and press OK button.
2.To surf through the channels use the PROG~or the
PROG €button or the channels can be directly
accessed by pressing “-/—” button and by pressing the
desired channel numbers.
VOD (Video On Demand)
1. Go to VOD option and press OK button.
2. Enter the password (default 1234).
3. To browse through movie list, press the PROG~or
the PROG€button and then press the OK button to
start playing the movie.
4. The movie can be forwarded by pressing the FF „„
button and fast rewind using the REW ƒƒ button
and pressing play button after selecting the size of
tracks to be skipped.
5. The movie can be paused by pressing the PAUSE
button and continue from the same position by
pressing the PLAY button.
6. While watching VOD if you switch to some other
application (Channels, Radio) and after some time
you again come back to VOD, it will ask you to
continue the same movie or start the new movie.
To continue the same movie press OK and to cancel

WICE.box User Manual8
the current movie and start new movie press K4
from remote.
7. While watching VOD if power goes off or
WICE.box resets, then after booting up select
VOD and enter password (default 1234). It will
ask you to continue the same movie or start the
new movie. To continue the same movie
press OK and to cancel the current movie and
start new movie press K4 from remote.
Radio
1. Go to RADIO option and press OK button.
2. To surf through the audio channels press PROG~
or the PROG€button and the radio channels will
change automatically.
SMS & E-MAIL
These selections will require the optional remote IR
interface module for keyboard and the PS/2
compatible keyboard (not supplied by manufacturer).
1. Plug in the keyboard into the IR interface module.
2. Press START button on the IR interface module.
3. To check anytime if the keyboard is active press
the Scroll Lock key on the keyboard. If the Scroll
Lock led blinks the keyboard is active. The
keyboard interface will automatically turn off to
extend battery life, if there is no activity for more
than 5 minutes. To re-activate the keyboard
interface press the START button once again.
SMS 1. Go to SMS option and press OK button.
2. A menu will be displayed as shown below
*SEND SMS
RECEIVE SMS
FRIEND LIST
QUIT
To send SMS press OK button from remote.
1. A message will be displayed “Mobile No: (PRESS
4. REMOTECONTROL

WICE.box User Manual 9
PROBLEMS SOLUTIONS
The WICE.box
does not work
at all
?Check if the LED on the left is glowing
when power is applied. If not, check the
AC power source.
When power is
applied, the
Menu appears
but does not
change when
buttons on re-
mote control
are pressed
?Check if Menu selection can be done
from the switches on front-panel.
?Check the 2 cells (AA) are inserted cor-
rectly into the remote
?Check if cells are used or low
?Check if the middle LED on front panel
blinks when any key of the remote control
is pressed
There is no
sound and pic-
ture. Even the
Main Menu is
not displayed
?Check the cables if they are connected
properly
?Check if the AV input is selected in TV
set
?Check the Video cable for any damage
No Sound ?Check the audio cable connections be-
tween WICE.box and TV
?Check the volume setting of the TV
?Check the volume setting of WICE.box
Main Menu is
displayed but
none of the
options work.
E.g. none of
the Broadcast
channels can
be viewed
?Check if the LED besides the RAMNET
connector on the rear panel is blinking. If it
is not blinking the trouble could be in the
incoming connection or cable.
?Check if you are connected and sub-
scribed to the services like Broadcast
Channels, Video-on-demand, SMS, Email,
Radio, etc.
4. REMOTE CONTROL
ESC)”.
2. Now enter the mobile number to which you need to
send the SMS.
3. Press Esc key on the keyboard to go to the next
step. (Remember not to press the Enter key.)
4. A message will be displayed “MESSAGE: (PRESS ESC)”
5. Enter your message and press Esc key. You may
press Enter key to go to a new line of your
message.
6. The same menu as shown above will be displayed
to indicate the confirmation of send SMS.
7. To check your INBOX select RECEIVE SMS and
press OK.
INBOX:
The SMS in your INBOX will be displayed one by one
with the latest SMS first and a submenu will be
displayed as shown below
1. *DELETE
2. REPLY
3. FORWARD
4. SAVE IN FRIENDLIST
NEXT QUIT
1. To delete the SMS select DELETE and press OK.
2. The SMS will be deleted and the next SMS will be
displayed on the screen or error message
(INBOX EMPTY) will be displayed if no SMS is
present.
REPLY:
1. To reply back to the mobile number select REPLY
and press OK.
2. A message will be displayed MESSAGE: (PRESS ESC)
Enter your message and press Esc.
3. The same SMS will be displayed back in
confirmation to reply SMS.
4. To forward the SMS to other mobile select
FORWARD and press OK.
5. A message will be displayed “Mobile No: (PRESS
ESC)”

WICE.box User Manual10
6. Enter the mobile number to which you want to
forward the SMS and press ESC. (Remember
not to press the Enter key).
7. The same SMS will be displayed back in
confirmation to forward SMS.
8. To save the mobile number in your friend list
select SAVE IN FRIEND LIST and press OK.
9. A message will be displayed “ENTER FRIEND
NAME: (MAX. 8 CHAR)”
10. Enter the friend name and press ESC.
11. The same SMS with the mobile number
replaced with the friend name will be
displayed back in confirmation to save in
friend list.
FRIEND LIST:
To manage the friend list select FRIEND LIST and
press OK.
1. A submenu will be displayed as shown below
1. *ADD FRIEND
2. VIEW FRIEND LIST
QUIT
2. To add a friend select ADD FRIEND and press
OK.
3. A message will be displayed “MOBILE NO:
(PRESS ESC)”
4. Enter the mobile number and press ESC.
5. A message will be displayed “ENTER FRIEND
NAME: (MAX. 8 CHAR)”
6. Enter the friend name and press ESC.
4. REMOTECONTROL

WICE.box User Manual 11
4. REMOTE CONTROL
USER PASSWORDS
The default passwords are
•Press 1234 for VOD menu.
•Press 3792 to get the default settings.
To change the default password to your own
password, press MENU key of the remote and
then press SETUP key. A menu shown below will
be displayed
USER PASSWORD MENU
1. *CHANGE VOD PASSWORD
2. GET DEFAULT SETTINGS
QUIT
1. To change the VOD password select
“CHANGE VOD PASSWORD” and press OK
2. A message will be displayed “ENTER OLD
PASSWORD:”
3. Enter old password (default 1234) and press
OK from remote.
4. A message will be displayed “ENTER NEW
PASSWORD: “
5. Enter new password which you want and
press OK from remote.
6. A message will be displayed “CONFIRM
PASSWORD:”
7. Re-enter the new password and press OK
from remote.
8. The WICE.box will get reset for confirmation
of password change.
9. To get back the default settings of the
WICE.box select “GET DEFAULT SETTINGS”
and press OK.

WICE.box User Manual12
4. REMOTECONTROL
10. A message will be displayed
“PRESS KEY SEQUENCE:”
11. Enter the key sequence 3792 and press OK
from remote.
12. The WICE.box will get reset to the default
settings.
NOTE: The key sequence to get the default
settings can not be changed.

WICE.box User Manual 13
PROBLEMS SOLUTIONS
The WICE.box
does not work
at all
?Check if the LED on the left is glowing
when power is applied. If not, check the
AC power source.
When power is
applied, the
Menu appears
but does not
change when
buttons on re-
mote control
are pressed
?Check if Menu selection can be done
from the switches on front-panel.
?Check the 2 cells (AA) are inserted cor-
rectly into the remote
?Check if cells are used or low
?Check if the middle LED on front panel
blinks when any key of the remote control
is pressed
There is no
sound and pic-
ture. Even the
Main Menu is
not displayed
?Check the cables if they are connected
properly
?Check if the AV input is selected in TV
set
?Check the Video cable for any damage
No Sound ?Check the audio cable connections be-
tween WICE.box and TV
?Check the volume setting of the TV
?Check the volume setting of WICE.box
Main Menu is
displayed but
none of the
options work.
E.g. none of
the Broadcast
channels can
be viewed
?Check if the LED besides the RAMNET
connector on the rear panel is blinking. If it
is not blinking the trouble could be in the
incoming connection or cable.
?Check if you are connected and sub-
scribed to the services like Broadcast
Channels, Video-on-demand, SMS, Email,
Radio, etc.
5. TROUBLE SHOOTING

WICE.box User Manual14
Power Source : AC 230V +/-10%, 50 Hz
Power Consumption : 8 W maximum
Input Connectivity : UTP Cable to RAMNet
Data Connectivity : Ethernet 10Mbps, Half-duplex
S-Video : Y-C signal (mini-DIN)
Composite Video : 1V p-p CCVS
Audio Out : Stereo left and right channel
Line level signal
Headphone Output : Stereo, 105mW into 16Ù each
Temperature : 5°C to 50°C
Weight : 1.7 Kg
Dimensions :325mm(w)x70mm(h)x180mm(d)
6. TECHNICAL SPECIFICATIONS

WICE.box User Manual 15
7. SERVICE RECORD

WICE.box User Manual16
8. NOTES

WICE.box User Manual 17
for latest update of User Manual please visit “www.divinetaccess.com/manuals”
Document Version : 3.0
ADDRESS:
DiviNet Access Technologies Ltd.
Shivdatta Plaza, Opp. Bus Depot,
Paud Road, Kothrud,
Pune -411038,
Maharashtra,
India.
Tel : [phone]
Fax : [phone]
e-mail :[email protected]
[email protected]
WEB : www.divinetaccess.com