DivioTec Full HD Speed Dome IP Camera User manual

Full HD Speed Dome IP Camera Quick Guide
This guide is for quick installing and connecting the Full HD Speed Dome IP Camera. For more details, please refer to
the User’s Manual of the camera in the supplied CD.
Camera’s Connectors
Indoor Outdoor
Pin
Connector
Definition
1
Alarm I/O
Alarm I/O connection
2
Default Button
Press the button with one figure for at least 20 seconds to restore the system.
3
Audio I/O
Audio I/O connection
4
RJ-45
For network and PoE+ connections
5
Power (AC 24V)
Power connection
6
microSD Card Slot
Insert the microSD card into the card slot to store videos and snapshots.
Do not remove the microSD card when the camera is powered on.
NOTE: It is not recommended to record with the microSD card for 24/7 continuously, as it may not be able to
support long term continuous data read/write. Please contact the manufacturer of the microSD card for
information regarding the reliability and the life expectancy.
Power Connection
To power up the camera, connect the AC 24V power adaptor to the power connector of the camera and the power
outlet. Refer to the diagram and the pin definition table below for connection. Alternatively, users can use an Ethernet
cable and connect it to the RJ-45 connector of the camera and an IEEE 802.3at 60W PoE+ switch.
Pin
Definition
1
AC 24V 1
2
GND
3
AC 24V 2
Ethernet Cable Connection
Connect one end of the Ethernet cable to the RJ-45 connector of the camera, and plug the other end of the cable to
the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the
PC.
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
the LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
Alarm I/O Connection
Please refer to the diagram and pin definition tables below for alarm I/O connection.
Pin
Definition
Pin
Definition
Pin
Definition
Pin
Definition
1
Alarm Out NO 1
4
GND
7
Alarm Out COM 2
10
Alarm In 3
2
Alarm Out NC 1
5
Alarm Out NO 2
8
GND
11
Alarm In 2
3
Alarm Out COM 1
6
Alarm Out NC 2
9
Alarm In 4
12
Alarm In 1
Audio I/O Connection
Please refer to the diagram and the pin definition table below for audio I/O connection.
Pin
Definition
1
Audio Out
2
GND
3
Audio In
Before Login to the Camera
A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the
camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
plug-ins or setting Internet’s security level to default. For further details, please refer to the User’s Manual in the
supplied CD.
ActiveX Controls and Plug-ins Settings
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>, and click on <Custom level> to
change ActiveX settings.
Step 4: Set “ActiveX controls and plug-ins”items to
<Prompt> or <Enable>.
Step 1: Start the IE Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>.
Step 4: Down the page, click on <Default Level> and
<OK> to confirm the setting. Close the browser
window, and open a new one later for
accessing the IP camera.
Camera Login
The default IP address of the camera is: 192.168.0.250. Therefore, to access the camera for the first time, please set
the IP address of the PC as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID & Password
Key in the camera’s IP address in the URL bar of the web browser window and hit “Enter”.
Enter the default username (Admin) a nd password (1234) in the prompt request dialogue. Note that
username is case sensitive.

Install the ActiveX Control
After connecting to the camera, the request for installing the ActiveX control will appear just below the URL bar.
Right click on the information bar and click on <Install ActiveX Control…> to permit ActiveX control installation.
In the pop-up security warning window, click on <Install> to start downloading DC Viewer software on the PC.
Click on <Finish> after DC Viewer installation is completed.
Browser-based Viewer
The main page of the IP camera user interface is as shown below.
Full HD Speed Dome IP Camera
Quick Guide
Ver. 1.6