DMP Electronics 862N User manual

2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
862N Network Interface Card and 862P Printer Interface Card
Description The862Ncardallowsthe1912XRCommandProcessor™Paneltocommunicatealarmandsystemreports
to the central station over existing data networks. The 862N provides selectable baud rate settings and
Transmit and Receive LEDs for verifying network communication.
The 862P card allows you to connect a serial printer to the 1912XR and provide local activity reports of
system events. The 862P is suitable for use with the SCS-PTR printer from DMP or a compatible 40 or 80
character serial printer.
Expansion Modules
The 862 card also provides a 4-wire
LX-Bus™ allowing you to connect
additionalzoneandoutputexpander
modulesorsinglepointexpandersto
the 1912XR panel.
Installing the 862 module
1. Remove AC and battery power
from the 1912XR panel before
installing the 862 card.
2. Remove the paper strip from the
base of the plastic standoff.
3.Carefullyalignthe40pinconnector
ofthe862withtheJ9connectoron
the 1912XR panel.
4. Gently press the 862 onto the J9
connector while applying even
pressure to both sides.
Installing the data cable
The data cable supplied with the 862 card contains one 8-pin modular end and one DB-25 male end.
1. Plug the cable's 8-pin modular end into the J1 Data Cable Connector on the 862.
2.Plug thecable's DB-25male endinto theappropriate connectoron yourdata networkequipment forthe
862N or serial printer for the 862P.
Referto thedocumentation suppliedwith yourdata networkequipmentfor additionalsystem connections.
Applying power to the 1912XR panel
After installing the 862 card and data cable, you can restore power to the 1912XR panel.
Installing expander modules
The LX-Bus™ on the 862 card allows you to add up to 100 zones of protection to the 1912XR using the
Models711,711E,714,and 715ZoneExpanders.Youcanalsoadd upto100Model6155LXorDS775LX
PIRs or 5845LX Glassbreak Sensors to the LX-Bus™. For output expansion, you can add multiple 716
Output Expanders (4 Form C outputs and 4 annunciator outputs) and 717 Graphic Annunciator Modules
(20annunciatoroutputs).PowerforthesedevicesisprovidedontheLX-Bus™throughtheBlack andRed
wires of the expansion harness.
To complete the installation:
1. Connect the Black wire (J13) from the 862 card to terminal 10 on the 1912XR panel.
2. Connect the Red wire (J14) from the 862 card to terminal 7 on the 1912XR panel.
LT-0202(10/98)
Figure 1: Installing the 862 on the 1912XR panel
INSTALLATION 1912XR Interface Cards
1912XR Panel
Bk - Aux. Common
Gr - Serial Data Out
Yl - Serial Data In
Rd - Aux. Positive
The 862 card plugs onto the J9
Expansion Connector on the 1912XR
Black
Red - To terminal 7
Black - To terminal 10
Adhesive backed standoff
attaches to microprocessor.
Red
Receive and
Transmit Jumpers
J6 and J7
{
Loop Expander Harness
for connecting loop and
output expander modules
to the 862 card.
J1 Data Cable Connector.
J3 Loop Expansion Connector.
Baud Rate Jumpers
J11 and J12
FORCE CTS Jumper
J15

DB-25 pinout description Description 862N Pin # 862P Pin #
Data Terminal Ready 20 20
Clear to Send 5 5 & 11
Ground 7 7
Receive Clock 17 17
Transmit Clock 15 15
Receive Data 3 2
Transmit Data 2 3
Request to Send 4 4
862N configuration jumpers
The two RECEIVE and TRANSMIT (or PLL) jumpers labelled J6 and J7 are preset to Yes allowing you to
match your network's data baud rate. Use the J11 and J12 jumpers to set the 862 card's baud rate to 150,
300, 1200, 2400, or 4800 as needed.
If your network supplies its own data clock, and thus is able to set the appropriate baud rate, move both
J6 and J7 jumpers to No and set the J11 and J12 jumpers to EXT (for external clock).
FORCE CTS jumper
If your network does not supply a Clear To Send signal, set the FORCE CTS jumper (J15) to FORCE to
allow the 862 card to supply its own CTS signal.
862P configuration jumpers
The 862P is preset for printer operation of 1200 baud with 8 data bits, one stop bit , and even parity. You
can change the baud rate using the J11 and J12 jumpers on the 862 card to accommodate printers with
different requirements.
Printer reports
The 862P prints system reports as they occur. You can also manually print the full contents of the panel's
100 event buffer to the printer at any time. To do this, enter the DISPLAY EVENTS? option from the User
Menu and press the Select key under PRINT at the FRST LAST PRINT display. Events are then printed in
chronological order from the oldest to the newest.
1912XR requirements
The 862N card requires 1912XR panels with firmware version 108 or greater and the following 1912XR
programming options:
Under COMMUNICATION, select:
COMM TYPE: DNET (for data network communications)
2ND LINE YES (only when using digital dialer backup)
The 862P cards requires 1912XR panels with firmware version 109 or greater and the following 1912XR
programming options:
Under PRINTER REPORTS, select one or more of the following options:
ARM/DISARM YES (arming, disarming, and late to close reports)
LOOP YES (loop status changes)
USER COMMANDS YES (user code and schedule changes, outputs on/off, and user functions)
DOOR ACCESS YES (door access reports)
SUPERVISORY MSG YES (system monitors and system events)
Refer to the 1912XR Programming Manual (LT-0171) for complete panel programming instructions.
Front View of DB-25 Connector
Digital Monitoring Products
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Pin 1 3
PIN 14 PIN 25
PIN 1