DMXPEN Rec01N 232 User manual

Manual / UK 1 DMXPEN Rec01N 232

INDEX
Introduction .................................................................. page 3
Warnings ...................................................................... page 4
Description ................................................................... page 5
SetUp / Connections ...................................................... page 6
Tec nical Specification ................................................... page 7
PIN Assignment ............................................................ page 8
Device Configuration ..................................................... page 9
Remote Control ............................................................ page 10
Warranty ...................................................................... page 12
Maintenance / Cleaning ................................................. page 12
Manual / UK 2 DMXPEN Rec01N 232

INTRODUCTION
T anks to buy t is DMXPEN series products.
A correct use of t is product, will ensure a correct functionality, a long life and at t e
same time will avoid product failure.
Please read t is manual carefully and be sure to understand t e information provide to
ensure a safe and reliable application, to learn a suitable knowledge of t e product and
is necessary precaution before using it.
Manual / UK 3 DMXPEN Rec01N 232

WARNINGS
1. T is manual describes t e DMXPEN Rec01N 232 operating functions. T e user
must operate t e product according to t e performance specifications described in
t e operation manuals.
2. W ile every effort as been made to ensure t at t e information on t is manual is
accurate and complete, we would appreciate any errors or omissions submitted to
our attention.
3. Maintenance, inspection, and replacement of parts must be performed only
by authorized personnel.
4. We reserve t e rig t to c ange t e specifications of t e ardware and software
described in t is manuals at any time and wit out prior notice.
5. Do not use DMXPEN Rec01N 232 wit wet finger
6. After t e package opening, please make t is c eck:
• T e received product correspond wit t e ordered one
• No part are missing on t e received product.
• T e product is not damaged.
• Contact immediately a DMXPen distributor in case of fault.
Manual / UK 4 DMXPEN Rec01N 232

DESCRIPTION
DMXPen Rec01N 232 device as t e following features:
–DMX512 Signal Recording and Playback
–ArtNet Signal Recording and Playback
–ArtNet - DMX Conversion
–DMX - ArtNet Conversion
–Remote control via MIDI interface
–Remote control via Et ernet interface
–Remote control via RS232 interface
Briefly t e DMXPen products mission is record and carry easily: “Design your s ow, record and
bring wit you”.
W y recording? T e first goal of a professional lig t programmer is to select a lig t desk and
learn to use it in t e best way, because t is means freedom of expression and productivity.
T e DMXPen products range improve t is concept taking care of recording w at t e lig t
programmer realize w it is preferred equipment.
W y carry? Often t e lig t programmer presence is not necessary during t e s ow playback, so
e can realize t e s ow and record it so t e user as only t e duty to activate is playback (i.e.
fair boot , s op, club, etc.)
Moreover doing t is wit a normal lig t desk, mean carry eavy or expensive equipment t at
usually are not so familiar to t e users (i.e. barman, custodian, etc.).
T is is anot er issue improved from t e DMXPen products because contains only t e s ow
engine wit a simple user interface at a very low cost.
Manual / UK 5 DMXPEN Rec01N 232

SET UP/CONNECTION
Be sure to ave t e microSD card inserted on t e socket (t e product is supplied wit t e
microSD card inserted on t e socket).
Note: t e device do not as a main ON/OFF switc and is necessary remove power
supply to make maintenance.
Note
Number
Description Device Connector Wiring Connector
1 Power Supply Input Jack Socket DC 2.0
(Switc craft 722A)
Jack Plug DC 2.0
(Switc craft S760K)
2 RS232 Port DSUB 9 Pole Female DSUB 9 Pole Male
3 Et ernet Port RJ45 Female RJ45 Male
4 MIDI (IN/OUT) Port DIN 5 Pole Female DIN 5 Pole Male
5 DMX512/A Input XLR 5 Pole Neutrik Male XLR 5 Pole Female
6 DMX512/A Output XLR 5 Pole Neutrik
Female
XLR 5 Pole Male
Technical Specification
Dimension ( L x W x H ) 92 x 113 x 33 mm
Weig t 350 gr.
Material / finis ing Iron / Fire Painted
Degree Protection IP 30
Operating Relative Humidity : from 30% to 85% wit out condensation
Operating Temperature -5°C + 50°C
DMX IN DMX512/A Input Data
DMX OUT DMX512/A Output Data
Power Supply 12-24 VDC – 500 mA
RS232 - 1 full duplex c annel
- 500 Mbps max. communication speed
MIDI - 1 MIDI IN port
- 1 MIDI OUT port
Manual / UK 6 DMXPEN Rec01N 232
1
2
3
4
5
6

MicroSD card - 1 MicroSD card socket
- FAT16 file system
Et ernet - IEEE 802.3 10BaseT Et ernet interface
Power supply - 12-24 VDC
- 200-500 mA
standard reference
EN 55022, EN 61000-4-2, EN 61000-4-4, EN 61000-4-5,
EN 61000-4-6, EN 61000-4-11, EMC 89/336/CEE,
BT 73/23/CEE
Manual / UK 7 DMXPEN Rec01N 232

PIN ASSIGNMENT
Manual / UK 8 DMXPEN Rec01N 232
MIDI – DIN 5 Pole Female
Pin Description
4 MIDI IN+ (Anode)
5 MIDI IN- (Kat od)
1 MIDI OUT+ (+5V wit 220o m)
3 MIDI OUT- (Signal)
Power Supply
Pin Description
1 GND
2 12-24VDC
DMX IN – XLR 5 Pole Male
Pin Description
1 GND
2 DMX-
3 DMX+
RS 3 – SUBD 9 Pole Female
Pin Description
1
2 TX
3 RX
4
5 GND
6
7
8
9
DMX OUT – XLR 5 Pole Female
Pin Description
1 GND
2 DMX-
3 DMX+

DEVICE CONFIGURATION
DMXPen Rec01N 232 is provided wit t e standard DMXPen engine t at allow remote
control via et ernet port using PenSuite software tools (PenSuite is a free software tools
available on t e device micorSD card or on www.dmxpen.com web site in bot PC and
MAC OS version).
Manual / UK 9 DMXPEN Rec01N 232

REMOTE CONTROL
Remote Control via Ethernet Port (PenSuite)
As indicate on t e previous paragrap , connecting DMXPen to t e et ernet port and using
t e PenSuite software tools (PenSuite is a free software tools available on t e device
micorSD card or on www.dmxpen.com web site in bot PC and MAC OS version) t is
functions will be available:
– Start s ow playback
– Start s ow recording
– Data direction selections
– ArtNet signal transmission
– ArtNet signal receptions
Remote Control via MIDI Port
Start s ow playback To start a s ow playback using a MIDI device, it's enoug
to send a “MIDI Program C ange” command using t e
s ow number as parameter. In example MIDI Program
C ange 1, will start s ow 1 playback.
ArtNet – MIDI Conversion Il passaggio da 0 al 100% dei C 1-C 127 generano un
evento MIDI Note ON per le note 1-127. Il passaggio da
0 al 100% dei C 128-C 255 generano un evento MIDI
Program C ange 1-127.
DMX – MIDI Conversion Il passaggio da 0 al 100% dei C 1-C 127 generano un
evento MIDI Note ON per le note 1-127. Il passaggio da
0 al 100% dei C 128-C 255 generano un evento MIDI
Program C ange 1-127.
Remote Control via RS 3 Port
DMXPen serial port data format is 19200,N,8,1 and t e communication protocol is based
on readable ASCII c aracters followed by a CR (ASCII13).
Here, eac time we type <CR> we refer to t e ASCII13 c aracter, t e CR.
DMX - ArtNet Data Direction $DDA<CR>
Configure t e DMX port as data input. Et ernet port will
send t e received frame using t e ArtNet protocol at t e
broadcast address configured wit PenSuite
ArtNet - DMX Data Direction $DAD<CR>
Configure t e ArtNet on t e et ernet port as data input.
DMX port will send t e received frame. Use PenSuite to
configure t e device universe number and IP and
broadcast address.
Start s ow playback $Gxxx<CR>
Start s ow xxx playback
Start s ow recording $Rxxx<CR>
Start s ow xxx recording
Stop s ow playback/recording $STOP<CR>
Stops any playback or recording
Manual / UK 10 DMXPEN Rec01N 232