DNF Controls 2044CL-O-EVS User manual

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 1
Model No. 2044CL-O-EVS
(& 2044CL-O-T)
300 CLIP INSTANT ACCESS SYSTEM
Odetics Protocol
For EVS Video Servers
USER MANUAL
12843 Foothill Blvd.,
Suite D
Sylmar, CA 91342
818 898 3380 voice
818 898 3360 fax
www.dnfcontrols.com

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 2
Table of Contents
1. REVISION HISTORY 4
GETTING STARTED . . . 5
2. SYSTEM DESCRIPTION 5
DEFINITIONS 5
3. SYSTEM INSTALLATION 6
A. SHOTBOX 6
B. ST400-S/SM, VTR/DDR CONTROLLER 6
4. VIDEO SERVER SETUP 7
5. LOAD A CLIP 7
ON THE ST400 7
6. LEARN A CLIP OR CLIP COMBINATION 8
A. ON THE ST400 8
B. ON THE SHOT BOX 8
7. RECALL A CLIP OR CLIP COMBINATION 9
ON THE SHOTBOX 9
8. RECUE CLIP 9
9. LEARN FROM THE ST400 10
A. ODETICS PROTOCOL 10
B. BVW PROTOCOL 11
10. RECALL FROM THE ST400 12
11. CLEAR CUE POINTS 12
A. ON THE ST420 SHOTBOX 12
B. ON THE ST400 12
12. LOOP CLIP 13
ON THE ST400 13
13. PLAY CLIP SEGMENT 13
14. TIMECODE SEARCH 14
15. BVW MODE 14
ADVANCED FEATURES . . . 15
16. SHOTBOX SHOTKEY MAPPING TO SHOTLIST LOCATIONS 15
17. SHOTBOX CONTROL SWITCHES 15
18. CREATING A CLIP 15
ON THE ST400 15
19. CAPTURE 16
20. VIEW SHOTKEY ASSIGNMENTS 17
ON THE SHOTBOX 17
21. CREATE CUE POINT LABELS 17
ON THE ST400 17

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 3
REFERENCE . . . 18
22. SETUP MENU 18
23. FUNCTION TABLE 21
24. SPECIFICATIONS 23
A. ST400 23
B. ST420 (SHOTBOX) 25
25. TROUBLESHOOTING 26
ST420 TROUBLESHOOTING 26
26. KEY LAYOUT 27
27. DNF CONTROLS LIMITED WARRANTY 28
Manual Version.....…............….............…............... 1.2 063005
Document ID......……........ 2044CL-O-EVS_User_Manual.doc

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 4
1. REVISION HISTORY
082504 1.0 Original document.
120104 1.1 Updated ST420 Troubleshooting section.
063005 1.2 Added Video Reference instructions.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 5
Getting Started . . .
2. SYSTEM DESCRIPTION
The 2044CL system includes DNF’s most robust controller, the ST400, with the industry’s
premiere Shotbox, the ST420.
The ST400 controls up to 6 video channels individually or ganged. It features full transport
functionality.
The LCD buttons on the Shotbox display clip names and delivery instant access to video clips on
up to 6 channels.
The assign-able keys on the ST420 Shotbox allow clip names to be organized on ten different
banks of keys for easy access.
The 2044CL provides instant access to fill clip and key clip combinations with the press of one
key.
The 2044CL-O-EVS supports Odetics Broadcast protocol and requires that the Video Server be
controllable under Odetics Broadcast Protocol.
DEFINITIONS
 Throughout this document, DDR, VDR & Video Server will be referred to collectively as
“Video Server.”
 The ST400-S/SM will be referred to as ST400.
 The ST420 SHOTBOX will be referred to as “Shotbox.”
SHOTKEY refers to the 1-30 switches on the Shotbox.
 Words surrounded by brackets, for example, [ENTER], are keys on the ST400 or the
SHOTBOX. [XXX] + [XXX] means hold the two keys down simultaneously.
 The 6 keys directly below the display are referred to as “Softkey.” Their function changes as
indicated on the last line of the display.
 Shotkeys and Cue Points refer to the same memory locations. Both terms are interchangeable.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 6
3. SYSTEM INSTALLATION
a. SHOTBOX
1) Plug one end of a standard 9-pin, RS422 serial cable into the OUTPUT
connector on the rear of the Shotbox. Plug the other end of the cable into
the “SHOTBOX” connector on the rear of the ST400.
2) Connect the supplied POWER SUPPLY, AULT#SW300, into the POWER connector
on the rear of the SHOTBOX. Plug the Power Supply into an outlet, 90 VAC – 240
VAC.
b. ST400-S/SM, VTR/DDR CONTROLLER
1) Plug one end of a 9-conductor, RS422 serial cable into the VTR1 (2, 3, 4, 5, or 6)
connector on the rear of the ST400. Plug the other end of the cable into the 9-pin
REMOTE connector on the Video Server.
2) Connect the supplied POWER SUPPLY, APX #4108, into the POWER connector on
the rear of the ST400. Plug the Power Supply into an outlet, 90 VAC - 240 VAC.
3) Check SETUP MENU prior to using the ST400 to confirm proper Record mode and
other User settable modes.
Attached House Video Reference cable to Ref. Video connector on the rear of the
ST400. Video Reference must be connected for frame accurate playout of ganged
channels, and for Capture function.
Installation is complete.
CONNECTION DIAGRAM

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 7
4. VIDEO SERVER SETUP
a. Select ODETICS Broadcast communications protocol on the VIDEO SERVER to be
controlled.
b. Assign a serial port on the VIDEO SERVER through which the ST400 will control it.
NOTES: The VIDEO SERVER may not support LTC or VITC time modes in ODETICS
Broadcast mode. The ST400 will default to Tape Time if a non-supported time mode is selected.
In ODETICS Broadcast mode, the VIDEO SERVER may ONLY allow Full Record. INSERT and
ASSEMBLE record modes may be disabled.
5. LOAD A CLIP
ON THE ST400
a. Select a VTR by pressing VTR [1], [2], [3], [4], [5], or [6].
b. Press [CLIP LIST] to view the list of CLIP IDs that are resident on the Video Server.
The CLIP LIST indicator will turn on.
c. Press [CREATE] to create and load a new clip.
(Creating a clip is described in the CREATING A CLIP section.)
OR
Turn the Wheel to view the existing CLIP IDs on the video server.
Turn the Wheel clockwise to scroll forward, or counter-clockwise to scroll backward,
through the list of available CLIPs. Backward scrolling is limited to the last 10 screens of
CLIP IDs.
If the description was entered on the EVS server, it is displayed next to the CLIP ID.
Press [LOAD] to load the highlighted CLIP ID. After loading the selected clip, the CLIP
LIST function will terminate. The CLIP LIST indicator will turn off.
OR
Manually enter a Clip ID using the ST400 numeric keypad or Shotbox “QWERTY”
keyboard, or PC keyboard.
Press [LOAD] to load the entered CLIP ID for playout.
d. Repeat steps a - c to load clips on desired VTRs.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 8
6. LEARN A CLIP OR CLIP COMBINATION
a. ON THE ST400
1) Press VTR [1], [2], [3], [4], [5], or [6] to select the channel to learn.
2) Load a clip on the selected channel. See section LOAD A CLIP.
3) Use the transport functions to view the clip.
Press [IN] to mark an IN point. The IN LED will turn on.
On recall, the clip will cue to the IN time, not the beginning of the clip.
Optional: Press [OUT] to mark an OUT point. The OUT LED will turn on.
On recall, the clip will play to the OUT point then stop.
To delete an IN or OUT point, press and hold [DEL], then press [IN]or [OUT].
The IN/OUT LED will turn off.
If no IN point is marked, the current location of the clip will be learned as the IN
point.
4) For GANGs, repeat steps 1 and 2 for each channel.
Then, press the [GANG] softkey.
Press VTR [1], [2], [3], [4], [5], or [6] to add it to the GANG. The VTR LED
will turn on.
Press the VTR key again to remove it from the gang. The VTR LED will turn
off.
Press [ESC] to exit GANG mode. The LEDs of all GANGed VTRs will turn on.
b. ON THE SHOT BOX
1. Press [LEARN]. The LEARN indicator will turn on.
2. Select the desired BANK by pressing BANK [1], [2], [3], [4], [5], [6], [7], [8],
[9] or [0].
3. Press the desired Shotkey to complete the learn process.
The learned CLIP ID is displayed on the Shotkey.
4. Press [ESC] at anytime to escape without LEARNing.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 9
7. RECALL A CLIP OR CLIP COMBINATION
ON THE SHOTBOX
a) Select the desired BANK by pressing BANK [1], [2], [3], [4], [5], [6], [7], [8], [9] or [0].
The Shotkeys will display the assigned CLIP IDs for the selected bank.
b) Press the desired Shotkey.
The selected clip or clip combination will be loaded on the learned channels, and cued to
the learned IN point. The learned OUT point and GANG mode will be set.
8. RECUE CLIP
a. Press [RECUE]. If an IN Point is marked (the IN indicator is on), the clip will RECUE to
the IN Point.
If the IN point is not marked, the clip will RECUE to the start of the clip.
b. Press [CUE OUT] to cue to the marked OUT point.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 10
9. LEARN FROM THE ST400
a. ODETICS PROTOCOL
1) Press VTR [1], [2], [3], [4], [5], or [6] to select the channel to learn.
2) Use the transport functions to view the clip.
Press [IN] to mark an IN point. The IN LED will turn on.
On recall, the clip will cue to the IN time, not the beginning of the clip.
Optional: Press [OUT] to mark an OUT point. The OUT LED will turn on.
On recall, the clip will play to the OUT point then stop.
To delete an IN or OUT point, press and hold [DEL], then press [IN]or [OUT].
The IN/OUT LED will turn off.
If no IN point is marked, the current location of the clip will be learned as the IN
point.
3) For GANGs, repeat steps a and b for each channel.
Then, press the [GANG] softkey.
Press VTR [1], [2], [3], [4], [5], or [6] to add it to the GANG. The VTR LED
will turn on.
Press the VTR key again to remove it from the gang. The VTR LED will turn
off.
Press [ESC] to exit GANG mode. The LEDs of all GANGed VTRs will turn on.
4) Select the desired Cue Point by pressing [NEXT CUE], [LAST CUE] or by
manually entering the Cue Point using the numeric keypad, followed by
[ENTER].
The selected Cue Point number is shown on the bottom part of the display.
5) Press [SHIFT] + [LEARN] to initiate the LEARN.
The display will show: “Select VTRs to learn:--------”
6) Select the VTRs to learn by pressing VTR keys [1], [2], [3], [4], [5], and/or [6].
7) Press [LEARN] to complete the learn process.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 11
b. BVW PROTOCOL
1) Select the desired Cue Point by pressing [NEXT CUE], [LAST CUE], or by
manually entering the Cue Point using the numeric keypad.
The selected Cue Point number is shown on the bottom line of the display.
2) Locate the clip to the desired IN time. Press [IN] to mark the IN time.
3) Locate the clip to the desired OUT time. Press [OUT] to mark the OUT time.
4) Press [SHIFT] + [MARK] to start the LEARN.
The first line of the display will show “Select VTRs:”
The second line of the display will show “Mark-Lrn, ESC-cancel.”
5) Press VTR[1], VTR[2], VTR[3] or VTR[4] to select the VTR to be learned into
the current Cue Point.
If the VTRs are ganged, select one VTR that is part of the Gang. The rest of the
Gang will learn automatically.
6) Press [MARK] to complete the LEARN.
OR
Press [ESC] to exit without LEARNING.
The ST300 will: LEARN (save) the VTR number (1,2,3,4) and current IN &
OUT time to the selected Cue Point.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 12
10. RECALL FROM THE ST400
a. Select the desired Cue Point by pressing [NEXT CUE], [LAST CUE] or by manually
entering the Cue Point using the numeric keypad.
The selected Cue Point number is shown on the bottom of the display.
b. Press [LOAD] on the ST400.
The ST400 will automatically load the Learned clips on the Learned VTRs, cue the clips
to the Learned IN time, then set the Learned GANG mode.
11. CLEAR CUE POINTS
a. ON THE ST420 SHOTBOX
1) Select the desired BANK by pressing the desired bank key.
2) Press and hold the [SHIFT] key.
3) Press the desired Shotkey to be cleared.
After the cue point is cleared, the Shotkey will be blank.
b. ON THE ST400
1) Select the cue point to be cleared using [NEXT CUE], [LAST CUE], or
manually entering the cue point number.
2) Press [SHIFT] + [LEARN].
The CLEAR softkey will be displayed on the bottom of the display.
3) Press the [CLEAR] softkey to clear the cue point.
The cue point will be cleared and the display will return to the normal screen.
OR
Press [ESC] to escape without clearing.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 13
12. LOOP CLIP
ON THE ST400
a. Load the clip using CLIP LIST, or recall a cue point.
(The clip MUST be loaded from the 2044CL.)
b. Optional: Set an IN Point and/or OUT Point.
Jog/Shuttle to the desired IN point. Press [IN].
Jog/Shuttle to the desired OUT point. Press [OUT].
OR
Press [SHIFT] + [IN]. Manually enter the IN time on the numeric keypad. Press
[ENTER].
Press [SHIFT] +[OUT]. Manually enter the OUT time on the numeric keypad. Press
[ENTER].
c. Press [LOOP ENABLE].
The clip will immediately start looping.
NOTES: If the CLIP ID ends with an asterisk (“*”), it will automatically loop when either [LOOP
ENABLE] or [PLAY] is pressed.
Loop Clip will only work from the 2044CL. Loop Clip will not affect clips loaded from
the user Interface.
13. PLAY CLIP SEGMENT
a. Set an IN Point and OUT Point.
Jog/Shuttle to the desired IN point. Press [IN].
Jog/Shuttle to the desired OUT point. Press [OUT].
OR
Press [SHIFT] + [IN]. Manually enter the IN time on the numeric keypad. Press
[ENTER].
Press [SHIFT] +[OUT]. Manually enter the OUT time on the numeric keypad. Press
[ENTER].
b. Press [RECUE]. The clip will cue to the IN point.
c. Press [PLAY].
The clip will play from its current time to the OUT point, then stop.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 14
14. TIMECODE SEARCH
In order to properly search by Timecode, please select Timecode = NOT SUPPORTED menu
option for every channel connected to the Profile and Timecode = SUPPORTED for all other
channels.
To select “Timecode” option:
a. Press [MENU] key.
b. Turn the wheel until TIMECODE option is highlighted.
c. Press [CHANGE]softkey.
d. Press a softkey to select SUPPORTED or NOT SUPPORTED setting.
e. Press [ESC] twice to exit menu mode.
15. BVW MODE
If you wish to control a tape machine or a DDR with the 2044CL-O system, select control
MODE=BVW (see Setup Menu section). In this mode, the media is accessed by timecode, not by
clip names. The cuepoints in BVW mode consist only of IN point, OUT point and Gang
information.
The following functions are not available in BVW mode:
- View Clip ID
- Recue Clip
- Loop Clip
- Capture
- Create Clip
All other functions work as described in the manual.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 15
Advanced Features . . .
16. SHOTBOX SHOTKEY MAPPING TO SHOTLIST
LOCATIONS
The Shotkeys on the Shotbox access the cue point locations in the ST400 as follows:
BANK 0, Shotkeys 1 30 access cue point locations 001 030.
BANK 1, Shotkeys 1 30 access cue point locations 101 130.
BANK 2, Shotkeys 1 30 access cue point locations 201 230.
BANK 3, Shotkeys 1 30 access cue point locations 301 330.
BANK 4, Shotkeys 1 30 access cue point locations 401 430.
BANK 5, Shotkeys 1 30 access cue point locations 501 530.
BANK 6, Shotkeys 1 30 access cue point locations 601 630.
BANK 7, Shotkeys 1 30 access cue point locations 701 730.
BANK 8, Shotkeys 1 30 access cue point locations 801 830.
BANK 9, Shotkeys 1 30 access cue point locations 901 930.
17. SHOTBOX CONTROL SWITCHES
a. [PLAY]: Plays out the selected clip.
b. [RECUE]: Returns to the beginning of the clip.
c. [STOP]: Stops playout of the clip.
18. CREATING A CLIP
ON THE ST400
a. Press [CLIP LIST].
b. Press [CREATE]. The display will show the default CLIP ID.
c. Press [LOAD] to accept the default CLIP ID.
OR
Manually enter an ID with a maximum of 8 characters from the ST400 numeric keypad,
OR a PC keyboard, OR the Shotbox “QWERTY” keyboard.
NOTES: For numbers on the SHOTBOX keyboard, use bank keys [0]-[9].
EVS names should be in the forms 001A, 102B, etc.
d. Press [LOAD].
The clip will be created with the entered CLIP ID.
If the selected CLIP ID already exists, a warning message will be displayed. To load the
existing clip, press [ENTER]. Press [ESC] to exit without loading the existing clip.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 16
19. CAPTURE
This function allows clips to be recorded on to the Video Server from a video source (SOURCE)
such as a VTR. The SOURCE is connected to the VTR6 connector on the rear of the 2044CL-O.
Prior to performing a capture, press [MENU].
Set the PREROLL value for the SOURCE VTR. Typical value is 5 seconds.
Set the RECORD DELAY value. This is the record latency of the video server. Typical value is 3
(frames).
Select the destination Video Server Channel. The destination channel may be any VTR except
VTR6.
a. Press VTR [6] to initiate the Capture function.
b. Set an IN point on the SOURCE VTR.
Jog/Shuttle to the desired IN point. Press [IN].
OR
Press [SHIFT] + [IN]. Manually enter the IN time on the numeric keypad. Press
[ENTER].
c. Set an OUT point on the SOURCE VTR.
Jog/Shuttle to the desired OUT point. Press [OUT].
OR
Press [SHIFT] +[OUT]. Manually enter the OUT time on the numeric keypad. Press
[ENTER].
d. Press [DEST] softkey. The display prompts you to select a destination channel. Select
any channel from VTR1 to VTR5. Press [ENTER] to confirm your selection.
e. Press [CAPTURE] softkey.
The display will prompt for a CLIP ID.
Manually enter a CLIP ID (maximum of 8 characters) using the numeric keypad, the
Shotbox QWERTY keyboard, or PC keyboard.
Press [ENTER] to accept the entered CLIP ID.
The SOURCE VTR will preroll to its IN point, then play. The video server will start
recording at the SOURCE’s IN point and stop recording at the SOURCE’s OUT point.
The created clip will be loaded on the destination channel.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 17
20. VIEW SHOTKEY ASSIGNMENTS
ON THE SHOTBOX
a. Press [VIEW]. The VIEW LED indicator will turn on.
b. Select the desired BANK by pressing the appropriate bank key.
c. Press and hold the desired Shotkey.
d. The lcd display on the Shotkeys will show the current assignment of all 6 VTRs for the
pressed Shotkey.
e. Release the Shotkey when done viewing.
f. Repeat steps a through e.
21. CREATE CUE POINT LABELS
Use LABELS mode to assign meaningful names to cue points. Rather than viewing cryptic CLIP
IDs on the Shotkeys, LABELS provides a faster and easier method to select cue points.
If different parts of the same clip are assigned to many Shotkeys, LABELS allows a unique name
to be assigned to each Shotkey.
ON THE ST400
a. In Setup Menu, turn LABEL MODE on.
b. Select cue point to label.
c. Press the [LABEL] key.
d. Manually enter a label, up to 8 characters in length, using the numeric keypad, ST420
Shotbox QWERTY keyboard, or PC keyboard.
e. Press the [LOAD] shotkey on the Shotbox to assign the entered label to the selected cue
point.
OR
[ENTER] on the ST400.
OR
[ENTER] on the PC keyboard.
OR
[NEXT CUE] or [LAST CUE].
NOTE: Labels are saved in non-volatile memory in the ST400, not in the Shotbox. They are not
saved in the video server.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 18
Reference . . .
22. SETUP MENU
Press [MENU]. The MENU indicator will turn on.
The display will show the following parameters with their current settings.
Turn the wheel to select a menu option.
Press the [CHANGE] softkey to modify the current setting.
Press the [EXIT] softkey to exit the Setup Menu.
PARAMETER DESCRIPTION
WIND MODE Press Softkey to select:
HOLD (fast wind is maintained only while key is depressed.)
OR
LATCH (fast wind is maintained after key is released.)
Set the fast wind speed (3.9 to 23.7) by pressing the [SPD] softkey.
RECORD MODE Press [MENU] to select the desired record mode:
Lockout, Assemble, Crash (Full) or Insert.
Only in INSERT mode: Press the associated Softkey, located below the display, to toggle
Video(V), Audio1(A1), Audio2(A2), Audio3(A3) on/off, Audio4 (A4) on/off.
SLOMO Press the [TBAR] (or [WHEEL]) softkey to select the T-bar or wheel for slomo.
For T-bar:
The T-BAR has a speed range of 0 2x with a detent at 1x play speed
OR a range of 0 1x (detent at 1x Play speed).
Press [SPD-RNG] softkey to toggle between SLOMO speed ranges:
01x OR 0 2x.
Press [BACK] softkey to return to SLOMO MENU.
Press [ESC] to exit OR turn the Wheel to select another item.
For Wheel:
Press the [PRSET] sofkey to toggle between UPDATE and STATIC modes.
UPDATE; When exiting SLOMO mode, the last used speed is saved in the Preset
Speed register.
STATIC: The Preset Speed register is NOT updated when exiting SLOMO mode.
It is only changed by [SHIFT] + [SLOMO] (PRESET SLOMO).
Press [SPD-RNG] softkey to toggle between SLOMO speed ranges:
01x OR 0 2x.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 19
PARAMETER DESCRIPTION
SYNC Select the appropriate softkey to enable or disable the Reference Video input. [ON] [OFF]
RECORD KEY Select single button or 2-button record:
RECORD = [REC] Only
ORRECORD= [REC] + [PLAY]
RECALL
MODE Press [NORMAL] or [REDIR] (redirect).
REDIR-
When one and only one clip is learned into a Cue Point, the Clip will be REDIRECTED to load
on the currently selected VTR
NORMAL-
The cue point will load on the learned VTR.
PREROLL Enter Preroll value.
RECORD
DELAY Enter delay value. (Used by CAPTURE function.)
GANG
MODE [PERM] Permanent Gang-
The GANG can be created and undone only with the [GANG] softkey.
[TEMP] Temporary Gang-
Quickly create a GANG by pressing and holding a VTR key, then pressing other VTR keys.
Quickly undo the GANG by pressing any VTR key.
Video Reference must be connected for frame accurate playout of ganged channels.
STANDARD Press [NTSC] or [PAL] to select the video standard for time calculations.
PROTOCOL Select [ODETICS] or [BVW].
[ODETICS]
Select Odetics to allow clip functionality: Load, Create, Recue, View available Clips.
[BVW]
Select BVW to control video server like a VTR. In this mode, the clip must have already been
loaded.
TIMECODE
Select [NOT SUPPORTED] to have TC search on the GVG servers, or [SUPPORTED] for
all
other servers.

2044CL-O-EVS, 300 Clip Instant Access System, Odetics Protocol 20
PARAMETER
DESCRIPTION
CLEAR
MEM
[DFLTS] [CLR – LBL] [CLR – QS] [CLR-BNK] [BACK]
DFLTS
Set ST400 to factory defaults. Follow the prompts on the display.
Press [YES] to continue or press [NO] to exit without changing ST400.
CLR – BNK
Clears all cue points in the selected bank. Follow the prompts on the display.
CLR – QS
Clears all cue points in all banks. Follow the prompts on the display.
CLR – LBL
Clears all labels associated with cue points. Does not clear cue points.
Follow the prompts on the display.
BACK
Return to prior menu item.