Doc Green ESA 2000 User manual

ESA 2000 e-Scooter
Operating Manual
Article / IT number: 142143 Edition: 12/2018 Revision: Version 01
Original Operating Manual

2
Table of contents
Table of contents
Explanation of symbols 3
Package contents 4
Introduction 5
General information 6
Safety instructions 7
Technical specications 10
Assembly 11
Unfolding and collapsing the e-Scooter 12
Adjusting the height of the handlebars 13
Battery handling 14
Operation 17
Maintenance and care 21
Warranty / Guarantee 23
Environmental protection 26
Declaration of conformity 27
Customer service 28
Notes 29

3
WARNING!
CAUTION!
NOTE!
Explanation of symbols
The following symbols and signal words are used in
these assembly instructions, on the e-scooter or on
the packaging.
Explanation of symbols
Contains important information for avoiding damage to persons
(injuries)
Contains important information for avoiding damage to the de-
vice.
Highlights important information and hints
in the operating instructions.

4
Package contents
Package contents:
User manual
ChargerESA 2000 e-Scooter
E-Scooter ESA 2000
Bedienungsanleitung
Artikel / IT Nummer: 142143 Ausgabe: 12/2018 Revision: Version 01
Original Bedienungsanleitung

5
Introduction
Introduction
Thank you for choosing the ESA 2000 e-Scooter.
The e-scooter was designed for brisk, safe and
highly enjoyable locomotion. The user manual contains import-
ant information for safely operating and properly maintaining your
e-scooter. It is important that you observe all safety instructions
and precautions contained therein and are especially attentive
while riding. Personal injury and/or damage to property cannot
be excluded if the e-scooter is used improperly. This e-scooter
can be used by children aged 12 years and above and by per-
sons with reduced physical, sensory, or mental capabilities, or
lack of experience and knowledge if they are supervised or have
been instructed in the safe use of the device and understand
the hazards involved. Children may not play with the e-scooter.
Cleaning and user maintenance must not be carried out by
children unless they are supervised.
The manufacturer reserves the right to make changes to the
product. The operating manual and illustrations within it may
di󰀨er depending on the model.
We hope you enjoy the ESA 2000 e-scooter.

6
General information
General information
Electric brake
Handles
Rear-wheel brake
Deck
Folding mechanism
Motor
Charging port
Stand
Thumb throttle
Vibration light

7
Safety information
Please read the instructions in this manual carefully to help mi-
nimise any risks. Please note that even if you follow the instruc-
tions completely, there will be some remaining risk when using
the e-scooter.
• Always adjust your speed to the current situation to minimise
the risk of
accidents and injuries.
• Please strictly comply with the safety regulations stated in
the manual. The producer or distributor cannot be held liable
for any nancial loss, personal injury, material damage, acci-
dents or legal disputes resulting from the violation of the
safety regulations. The liability is always limited to the pur-
chase value of the e-scooter.
• Please check your e-scooter before each ride (see the main-
tenance and care section).
• Always wear a safety helmet, appropriate clothing, protective
equipment (hand/wrist protection, knee pads, headgear and el-
bow pads) and at-heeled shoes.
• Hold the handlebar with both hands while riding.
• Practise riding the e-scooter on open and level terrain.
• The e-scooter is not suitable for children under 12 years of age.
• The e-scooter has been designed to transport one person
with
a maximum weight of 100 kg.
• The e-scooter is suitable for use on at,
dry surfaces.
• Do not ride through water, in rainy conditions, at night or
Safety information

8
Safety information
when visibility conditions are poor.
• The e-scooter is not suitable for stunts – DO NOT ATTEMPT
to jump or perform any dangerous manoeuvres.
• Do not leave the e-scooter outdoors. Please store it in a dry,
dark location.
• Make sure that all bolts are tightened before
each ride.
• Be careful not to touch any moving parts while riding in
order to
avoid injuries.
• Note that the brake device
gets hot when used continually and
should not be touched after braking!
• The e-scooter vehicle (leisure vehicle) is designed for trans-
porting one person.
• According to road tra󰀩c regulations, every participant in pu-
blic road tra󰀩c must
behave in manner which does not cause other
road users to be endangered, harmed, harassed or hinde-
red! In order
to operate your e-scooter on public roads, it must comply
with the legal guidelines. The e-scooter must be fundamen-
tally equipped with two brakes that function independently of
one another, a bell, a brightly lit headlamp that illuminates
the path ahead with a steady, white or light-yellow light, and
must have a red rear light and reector strips.
Before starting to use your e-scooter,
check the current legal
provisions for your region by contacting the relevant
authorities.
• The e-scooter is equipped with a lithium-ion
battery. Please note that in some

9
Safety information
countries there are separate regulations for transporting
lithium-ion batteries.

10
Technical specications
Technical specifications
Motor: 250-Watt
rear-wheel motor
Battery: 25.2 V / 5.8 Ah
lithium-ion with LG cells
Charging time: approx. 4-5 hours
Brakes Electric rear-wheel brake,
rear friction brake
Features: Bell, headlight, rear light,
reflectors, reflector strips
Maximum load: 90 kg
Maximum speed*: approx. 23 km/h
Maximum distance*: approx. 10 km
Tyres: front: 6“ / rear: 5.5“
Weight: approx. 7.5 kg
*Guidelines for a user weight of approx. 75 kg and fully charged battery, on
smooth, even surfaces and in optimal temperature conditions (10°C - 30°C).

11
Assembly
Assembly
The e-scooter is ready to use in a few simple steps.
To assemble the handlebars:
Thumb throttle (1), electric brake (2) and bell (3) come pre-as-
sembled.
L
LR
3
21
R
ScrewthehandlesL(left)and
R (right) onto the handlebar
as shown above.
Transport
guard
Pull the transport
guard downwards.
Remove the transportation
safety device of the rear light.

The Smart Kick Scooter can be assembled within 2 minutes:
Install the Handlebars and tighten the handles.
You can unfold the Smart Kick Scooter without
any inconvenience in seconds.
2. Product Overview
3. Product Description
Before installing the handles,
please make sure to differenciate
the left & right handles carefully.
Please see the difference of left
& right handles from below images.
L
L
R
R
02
Pull up the tube of the folding construction,
then push down the front pole, when bottom
of the folding tube goes into the slot,the
folding completed.
The Smart Kick Scooter can be folded in a few
seconds at the press of a single lever.
Pull up the tube of the folding construction,
then pull up the the front pole, when bottom
of the folding tube goes into the slot,the
unfolding completed.
2.1 General information
2.2 What you need to know
3.1 Assembly 3.2 Folding 3.3 Unfolding
The power will be shut down if nobody operate in five minutes，you need press power button before you ride.
The Smart Kick Scooter can be assembled within 2 minutes:
Install the Handlebars and tighten the handles.
You can unfold the Smart Kick Scooter without
any inconvenience in seconds.
2. Product Overview
3. Product Description
Before installing the handles,
please make sure to differenciate
the left & right handles carefully.
Please see the difference of left
& right handles from below images.
L
L
R
R
02
Pull up the tube of the folding construction,
then push down the front pole, when bottom
of the folding tube goes into the slot,the
folding completed.
The Smart Kick Scooter can be folded in a few
seconds at the press of a single lever.
Pull up the tube of the folding construction,
then pull up the the front pole, when bottom
of the folding tube goes into the slot,the
unfolding completed.
2.1 General information
2.2 What you need to know
3.1 Assembly 3.2 Folding 3.3 Unfolding
The power will be shut down if nobody operate in five minutes，you need press power button before you ride.
12
Unfolding and collapsing the e-scooter
Unfolding
To unfold, pull the round hand-
le upwards and fold the hand-
lebar forwards. Then let go of
the round handle. Check that
the handlebar lock is engaged
before each ride.
Collapsing
To collapse, pull the round
handle upwards and fold the
handlebar backwards. Then
let go of the round handle.
Check that the handlebar lock
is engaged again after folding.
Unfolding and collapsing the e-scooter

03
3.4 How to ajust height of extension pole
4. How to ride
Warning:There is risk of falling down during
learning, so make sure to wear helmet and
protection kits all the time.
1.Turn on the scooter by press and check the battery
power.
3.Turn off the scooter when finish using the product. .
1. Open the lock buckle of extension pole. 2. Press down height-limit button (the metal bead in
hole of extension pole), and pull extension pole to
the length(3 levels of height for option) to fit rider's
height.When the bead goes into the hole, the
height is fixed.
3. Close the lock buckle
lock buckle
height-limit button
2. Press the accelerator slightly to accelerate.
Loose the accelerator to slow down gradually.
Press the brake handle to stop the scooter.
Do not stop suddenly.
03
3.4 How to ajust height of extension pole
4. How to ride
Warning:There is risk of falling down during
learning, so make sure to wear helmet and
protection kits all the time.
1.Turn on the scooter by press and check the battery
power.
3.Turn off the scooter when finish using the product. .
1. Open the lock buckle of extension pole. 2. Press down height-limit button (the metal bead in
hole of extension pole), and pull extension pole to
the length(3 levels of height for option) to fit rider's
height.When the bead goes into the hole, the
height is fixed.
3. Close the lock buckle
lock buckle
height-limit button
2. Press the accelerator slightly to accelerate.
Loose the accelerator to slow down gradually.
Press the brake handle to stop the scooter.
Do not stop suddenly.
03
3.4 How to ajust height of extension pole
4. How to ride
Warning:There is risk of falling down during
learning, so make sure to wear helmet and
protection kits all the time.
1.Turn on the scooter by press and check the battery
power.
3.Turn off the scooter when finish using the product. .
1. Open the lock buckle of extension pole. 2. Press down height-limit button (the metal bead in
hole of extension pole), and pull extension pole to
the length(3 levels of height for option) to fit rider's
height.When the bead goes into the hole, the
height is fixed.
3. Close the lock buckle
lock buckle
height-limit button
2. Press the accelerator slightly to accelerate.
Loose the accelerator to slow down gradually.
Press the brake handle to stop the scooter.
Do not stop suddenly.
13
Adjusting the height of the handlebar
Spring button
Adjusting the height of the handlebar
1. Open thequick-release me-
chanism of the handlebar.
2. Press the spring
button to set the desired
handlebar height.
The spring button must
engage in one of
the 3 holes in the
frame.
3. Close the quick-release
mechanism and make sure
it is secure.

14
Handling the battery
Charging the battery:
• Ensure that the charging port and charger are dry.
• Make sure that the e-scooter is turned off. Connect the charging
cable to the charging port of the e-scooter and then connect it to
a power outlet (~230 V / 50-60 Hz).
• Check that the charging light on the charger lights up red.
• The battery is charged once the charging light changes from
red to green. You should stop charging at this point.
• Disconnect the charger from the mains and the e-scooter.
• The e-scooter may only be charged with the supplied char-
ger. Take care to use the correct voltage supply (~230 V /
50-60 Hz).
• If the charger or mains connector is damaged, the charger
must not be used. Please contact customer service.
• For optimum battery life, charge and store
the e-scooter in a dry and clean environment,
preferably at a temperature of 7-15°C.
• The charging time of the e-scooter is approx. 4-5 hours.
Leaving the charger permanently connected to the battery and
power supply will have an adverse effect on the battery life.
• The e-scooter and the charger must not be covered during
charging.
Handling the battery
Important information on
battery handling!

15
• Depending on the charge state, lithium batteries have a free-
zing point of approx. -20°C to -25°C. If a battery cell freezes
it will be irreparably destroyed and the whole battery will need
to be replaced. As with conventional batteries, a lithium battery
loses up to 40% of its capacity from approx. 0°C.
• At approx. 20°C and 100% charge, a lithium battery loses
about 30% of capacity per month (poor storage).
• However, at approx. 7°C and 70% charge, a lithium battery
loses only about 5% of capacity per month (optimal storage).
• If a BMS (Battery Management System) is installed in a
lithium battery pack, then the self-discharge is comparable to
a conventional battery in storage (caution: intermediate char-
ge). The BMS system reduces battery capacity but is neces-
sary and mandatory for cell balancing (uniform cell dischar-
ge).
Handling the battery

16
Proper handling of the battery:
• Never remove the battery from the e-scooter.
• Charge the battery every 2 months for at least 1 hour, even if
the e-scooter has not been used.
• Never heat the battery or throw it into an open fire.
• Never dispose of battery cells in household waste.
• Never get moisture on the battery contacts.
• The best operating temperature for the battery is between
10°C and 30°C. The power output will deteriorate at tempera-
tures above or below this temperature, resulting in a reduced
maximum distance and power output.
A battery's service life and performance depends on its age,
care and how often it has been used. Compared to other battery
models, lithium-ion batteries have little self-discharge and a
reduced memory effect, but they must be charged periodically.
Even if you are not using your e-scooter, the battery must be
recharged every 2 months for at least 1 hour, otherwise it will
lose its capacity. Regular charging protects the battery from total
discharge. Please note that a totally discharged battery is irrepa-
rably damaged and has to be replaced for a fee. Therefore, the
battery should never be fully discharged, even during operation.
WARNING!
Handling the battery

17
• Wear comfortable leisure or sports clothing and flat-heeled
shoes when riding.
• Before riding for the first time, make sure you have plenty of
space and ensure that there are no obstacles in the way.
Riding operation:
• Unfold the e-scooter.
• Press the power button to turn the scooter on.
• Step onto the deck with one foot. Do not step on the rear-
wheel friction brake.
• Use the thumb throttle to accelerate
• You can use the rear-wheel friction brake and the
thumb brake (electric rear-wheel brake) to brake:
Operation
Thumb brake
(electric rear-wheel brake) Thumb throttle
Wear a safety helmet and
protective pads for your own
safety.
Operation
Before you begin

18
Display functions:
Rear-wheel brake:
Operation
1
3
2
4
5
6
7
A
1Charge level indicator
2Speed km/h
3
Selected
speed level
1: 5 km/h
2: 15 km/h
3: 23 km/h
4Odometer
5Increase
speed level
6
Power button
for switching the
e-scooter on and o󰀨
7Decrease
speed level
A
Tread here on
the rear-wheel
friction brake
to activate

19
Lighting:
Operation
B
Using the push button you can choose between 3 lighting mo-
des.
1. Press the button to switch it on. The LED lights ash at short
intervals.
2. Pressing again shortens the ashing intervals.
3. Press the button again for continuous illumination.
Press the button a fourth time to turn the light o󰀨.
BThe light switch is loca-
ted here

20
If the front-light battery is at, it must be replaced with an equi-
valent 3V CR2032 battery:
The rear light is plugged into the rear mudguard, is controlled by
sensors and cannot be manually switched on/o󰀨.
Furthermore, the battery in the rear light must be replaced by an
equivalent 3V CR1632 battery as soon as it is empty:
Always turn off the
• e-scooter after riding.
• Always turn o󰀨 the front light.
• Charge the e-scooter after every ride.
• Pull the locking lever to collapse the
e-scooter.
• Store the e-scooter in a horizontal position.
Operation