Dodge CHARGER 2019 User manual

2019 CHARGER QUICK REFERENCE GUIDE

Vehicle User Guide — If Equipped
To access the Vehicle User Guide on your
Uconnect Touchscreen: Tap the Uconnect Apps
button, then tap the Vehicle User Guide icon on
your touchscreen. No Uconnect registration is
required.
NOTE:
Vehicle User Guide features are not available
while the vehicle is moving.
Features
• Your User Guide — Updated in real-time
• Available when and where you need it
• Touchscreen convenience
• Customizable interface
• Maintenance schedules and information
• Multilingual
• Comprehensive icon & symbol glossary
Keyless Enter-N-Go — Passive
Entry
The Keyless Enter-N-Go system is an enhance-
ment to the vehicle’s key fob. This feature allows
you to lock and unlock the vehicle’s door(s) and
trunk without having to press the key fob lock or
unlock buttons.
To Unlock From The Driver Or
Passenger Side
Uconnect 4C NAV With 8.4–inch Display
Vehicle User Guide Touchscreen Icon
Grab The Door Handle To Unlock
VEHICLE USER GUIDE —
IF EQUIPPED
PASSIVE ENTRY

With a valid key fob located outside the vehicle
and within 5 ft (1.5 m) of the driver or passenger
side door handle, lift either front door handle to
unlock the door automatically.
To Lock The Vehicle
Both front door handles have buttons located on
the outside of the handle. With one of the vehicle's
key fobs located outside the vehicle and within 5 ft
(1.5 m) of the driver's or passenger front door
handle, push the door handle button to lock all
four doors and trunk.
Do NOT grab the door handle when pushing the
lock button. This could unlock the door(s).
NOTE:
• If “Unlock All Doors 1st Press” is programmed,
all doors will unlock when you grab hold of the
front driver's door handle.
• If a key fob is detected in the vehicle when
locking the vehicle using the power door lock
switch, the doors will unlock and the horn will
chirp three times. On the third attempt, your
key fob can be locked inside the vehicle.
• After pushing the button, you must wait two
seconds before you can lock or unlock the
vehicle using the door handle. This is done to
allow you to check if the vehicle is locked by
pulling the door handle without the vehicle
reacting and unlocking.
• If a Keyless Enter-N-Go — Passive Entry door
handle has not been used for 72 hours, the
Keyless Enter-N-Go — Passive Entry feature for
that handle may time out. Pulling the deacti-
vated front door handle will reactivate the door
handle's Keyless Enter-N-Go — Passive Entry
feature.
Push The Door Handle Passive Entry Button
To Lock
Do NOT Grab The Handle When Locking

To Enter The Trunk
With a valid key fob located outside the vehicle
and within 5 ft (1.5 m) of the trunk, push the
button on the right side of applique which is
located on the trunk.
Whenever the vehicle is unlocked, you can enter
the trunk by pushing the button on the right side of
the applique.
For further information, and applicable warnings
and cautions, please refer to the Owner’s Manual
at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Cana-
dian Residents).
Cluster Display
The instrument cluster display features a driver
interactive display that is located in the instru-
ment cluster. Pushing the controls on the left side
of the steering wheel allows the driver to select
Vehicle Information and Personal Settings.
Trunk Passive Entry Button
Instrument Cluster Display Controls
INSTRUMENT CLUSTER
DISPLAY

• Push the up arrow button to scroll upward
through the main menus (Speedometer, Ve-
hicle Info, Performance Pages – SRT only,
Driver Assist, Fuel Economy, Trip, Audio, Mes-
sages, Screen Setup) and sub menus.
• Push the down arrow button to scroll downward
through the main menus and sub menus.
• Push the right arrow button to scroll forward to
the next menu or sub menu.
• Push the left arrow button to scroll back to a
previous menu or sub menu.
• Push the OK
button to access/select the infor-
mation screens, the submenu screens of a main
menu item, or to select a personal setting in the
setup menu. Push and hold the OK
button for
two seconds to reset displayed/selected fea-
tures that can be reset.
Compass Calibration
This compass is self-calibrating, which eliminates
the need to set the compass manually. When the
vehicle is new, the compass may appear erratic,
and the cluster will display dashes (- -) until the
compass is calibrated.
You may also calibrate the compass by completing
one or more 360 degree turns (in an area free from
large metal or metallic objects) until the dashes
(- -) displayed in the cluster turn off. The compass
will now function normally.
For further information, and applicable warnings
and cautions, please refer to the Owner’s Manual
at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Cana-
dian Residents).
Pairing Procedure
Mobile phone pairing is the process of establishing a
wireless connection between a cellular phone and
the Uconnect system.
Start Pairing Procedure On The Radio
Uconnect 4 With 7-inch Display
1. Place the ignition in the ACC or ON position.
2. Press the “Phone” button.
3. Select “Settings.”
Uconnect 4 With 7-Inch Display
PHONE PAIRING

4. Select “Paired Phones.”
5. Select “Add device.”
•
Uconnect Phone will display an “In progress”
screen while the system is connecting.
Uconnect 4C & 4C NAV With 8.4-inch Display
1. Place the ignition in the ACC or ON position.
2. Press the “Phone” button in the Menu Bar on
the touchscreen.
3. Select “Pairing.”
4. Select “Paired Phones And Audio Devices.”
5. Select “Add Device.”
•
Uconnect Phone will display an “In progress”
screen while the system is connecting.
Pair Your iPhone:
To search for available devices on your Bluetooth
enabled iPhone:
1. Press the Settings button.
2. Select Bluetooth.
• Ensure the Bluetooth feature is enabled.
Once enabled, the mobile phone will begin
to search for Bluetooth connections.
3. When your mobile phone finds the Uconnect
system, select “Uconnect”.
Complete The iPhone Pairing Procedure:
1. When prompted on the mobile phone, accept
the connection request from Uconnect Phone.
NOTE:
Some mobile phones will require you to enter the
PIN number.
Uconnect 4C & 4C NAV With 8.4-Inch Display
Bluetooth On/Uconnect Device
Pairing Request

Pair Your Android Device:
To search for available devices on your Bluetooth
enabled Android Device:
1. Push the Menu button.
2. Select Settings.
3. Select Connections.
4. Turn Bluetooth setting to “On.”
• Ensure the Bluetooth feature is enabled.
Once enabled, the mobile phone will begin
to search for Bluetooth connections.
5. Once your mobile phone finds the Uconnect
system, select “Uconnect”.
• You may be prompted by your mobile phone
to download the phonebook, check “Do Not
Ask Again” to automatically download the
phonebook. This is so you can make calls by
saying the name of your contact.
Complete The Android Pairing Procedure:
1. Confirm the passkey shown on the mobile
phone matches the passkey shown on the
Uconnect system then accept the Bluetooth
pairing request.
NOTE:
Some mobile phones require the PIN to be en-
tered manually, enter the PIN number shown on
the Uconnect screen.
NOTE:
Software updates on your phone or the Uconnect
system may interfere with the Bluetooth connec-
tion. If this happens, simply repeat the pairing
process. However, first, make sure to delete the
device from the list of phones on your Uconnect
system. Next, be sure to remove Uconnect from
the list of devices in your phone’s Bluetooth set-
tings.
For further information on Uconnect Phone,
please refer to “Uconnect Phone” in the vehicle’s
User Guide.
Uconnect Device
Pairing Request

Automatic High Beam —
If Equipped
This system automatically controls the operation
of the headlamp high beams as oncoming vehicles
approach.
• The Automatic High Beam Headlamp Control
can be turned on or off using the Uconnect
System.
• Push the turn signal lever away from you.
•
With the headlight switch in the “AUTO” posi-
tion, the high beams are controlled automatically.
• Pull the turn signal lever toward you to manu-
ally deactivate the system.
• To improve system recognition of crossing traf-
fic, and to limit use in a residential area, the
vehicle must be moving at a speed greater than
20 mph (32 km/h) before the Automatic High
Beam Module (AHBM) begins requesting high
beam activation.
NOTE:
If the windshield or Automatic High Beam Head-
lamp Control mirror is replaced, the mirror must
be re-aimed to ensure proper performance. See an
local authorized dealer.
For further information, and applicable warnings
and cautions, please refer to the Owner’s Manual
at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Cana-
dian Residents).
Adaptive Cruise Control (ACC) —
If Equipped
If your vehicle is equipped with Adaptive Cruise
Control, the controls operate exactly the same as
the standard cruise control, with one difference.
You can set a specified distance you would like to
maintain between you and the vehicle in front of
you.
• If the ACC sensor detects a vehicle ahead, ACC
will apply limited braking or acceleration auto-
matically to maintain a preset following dis-
tance while matching the speed of the vehicle
ahead.
NOTE:
Your vehicle will not exceed the cruise speed you
have set.
• If the sensor does not detect a vehicle directly
ahead of you, it functions like a standard cruise
control system, maintaining the speed you set.
LIGHTS SPEED CONTROL

F or further information, and applicable warnings
and cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or
www.owners.mopar.ca (Cana-
dian Residents).
LaneSense — If Equipped
The LaneSense system is operational at speeds
above 37 mph (60 km/h) and below 112 mph
(180 km/h). The LaneSense system uses a forward
looking camera to detect lane markings and mea-
sure vehicle position within the lane boundaries.
Turning LaneSense On Or Off
The default status of LaneSense is “off”. The
LaneSense button is located on the center stack.
LaneSense Warning Message
The LaneSense system will indicate the current
lane drift condition through the instrument cluster
display. The instrument cluster display will pro-
vide a visual warning depicting the unintentional
lane departure.
When both lane markings are detected and the
driver unintentionally drifts out of the lane (no turn
signal applied), the LaneSense system provides a
haptic warning in the form of torque applied to the
steering wheel to prompt the driver to remain
within the lane boundaries. The driver may manu-
ally override the haptic warning by applying torque
into the steering wheel at any time. When only a
single lane marking is detected and the driver
unintentionally drifts across the lane marking (no
turn signal applied), the LaneSense system pro-
vides a visual warning through the instrument
cluster display to prompt the driver to remain
within the lane. When only a single lane marking is
detected, a haptic (torque) warning will not be
provided.
NOTE:
The LaneSense system can be customized and
turned off through the Uconnect System touch-
screen.
For further information, and applicable warnings
and cautions, please refer to the Owner’s Manual
at www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Cana-
dian Residents).
Adaptive Cruise Switches
1 — Adaptive Cruise Control (ACC) On/Off
2 — Distance Setting – Decrease
3 — Distance Setting – Increase
SAFETY FEATURES

Forward Collision Warning With
Mitigation — If Equipped
The Forward Collision Warning (FCW) system pro-
vides the driver with active braking, audible and
visual warnings [within the instrument cluster dis-
play] and may apply a brake jerk to warn the driver
when it detects a potential frontal collision. The
warnings and limited braking are intended to pro-
vide the driver with enough time to react and avoid
or mitigate the potential collision.
FCW monitors the information from the forward-
looking sensor, as well as the Electronic Brake
Controller (EBC) to calculate a probable collision.
When the system determines that a collision is
probable, a warning message (both audible and
visual) will be displayed within the cluster display
along with a brake jerk warning (previously en-
abled in the Uconnect Settings). When the system
senses the driver applying the brakes to avoid a
probable collision, additional brake force will be
provided to the vehicle. When the system deter-
mines a collision with the vehicle in front of you is
no longer probable, the warning message will be
deactivated.
NOTE:
The FCW feature can be customized and turned
off through the Uconnect System touchscreen.
F
or further information, and applicable warnings
and cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) or www.owners.mopar.ca (Cana-
dian Residents).
SRT Vehicles
Chassis
• Wheels - due to the high performance nature of
the brake system, the wheels will get coated
with brake dust. It is recommended that
Mopar
®
Wheel Cleaner be used on your wheels
to avoid any possible damage to the finish.
However, do not use wheel cleaner if your
vehicle is equipped with Dark Vapor or Black
Satin Chrome wheels, which must only be
cleaned with mild soap, water, and a soft cloth.
NOTE:
Due to the high performance nature of the brakes
on your SRT, vehicle dust and some noise are
expected and normal.
• Tire Service Kit - your vehicle comes with a tire
inflator kit; there is no spare tire included in
your vehicle.
• Trailer Tow - Trailer towing with your SRT ve-
hicle is not recommended.
• ESC (Electronic Stability Control) - your vehicle
is equipped with selectable ESC modes. The
ESC mode selected will alter the handling char-
acteristics of your vehicle.
STARTING AND OPERATING